Inhaltsverzeichnis
Werbung
GB
Congratulations! Your Universal Remote Control (URC) is a state-of-the-art
device which integrates many different infra-red remote controls to deliver
instant A/V action to your fingertips.
Before operating the remote, please read thoroughly (1) the inside of the
coversheet and (2) this manual. Then reserve them for future reference.
1
HOW TO INSTALL THE BATTERIES
Alkaline batteries are recommended. The number of batteries required is stated
on the back of the coversheet.
1. Remove the battery cover on the back of your URC.
2. Check the polarity of the batteries and the "+/–" marks inside the battery
compartment.
3. Insert the batteries.
4. Push the battery cover back in place.
Batter y Lo w
If the indicator flashes twice slowly after using the URC, it shows that the
battery level is low. You must replace them with new batteries to ensure proper
functioning.
2
HOW TO SET UP THE URC
By entering De vice Code
You may setup the URC by following the code entering instructions.
1. Referring to the DEVICE CODE LIST, look up the 4-digit Device Code which
corresponds to the brand of your A/V equipment. If there is more than
one Device Code listed under your brand, start from the first code.
2. Press the desired Device Mode Key (e.g.
3. Hold down " CH+ " and " VOL– "on the URC simultaneously for 2 seconds
until the indicator lights up.
4. Use the number keys
cator should go out immediately.
Turn on your device (e.g. TV), then try the function keys on the URC. If your
device (e.g. TV) responds to your activated function correctly, you have entered
the right Device Code. Otherwise, repeat the above steps with the next available
Device Codes until your device (e.g. TV) responds to your activated function,
and most keys work correctly.
* Simply repeat the above procedures to enter the Device Codes for your
SAT, or DVD. (Remember to press the correct Device Mode Key in step 2
above)
Note :
– DVD and other Device Codes can be entered into any device modes
except "TV" & "SAT" modes. Simply press the device mode key and
enter your 4-digit device code for DVD and other devices.
If the indicator flashes twice in step 4, a wrong Device Code has been
entered. You are required to repeat step 2 to 4 again.
Suggestion :
– If you cannot find a correct Device Code for your equipment, see
TO SET UP THE URC– By Searching Through the Library.
– For future reference you are recommended to take a note of your Device
Codes in the space provided on the product's back label after setting up
the URC correctly.
).
TV
to enter your 4-digit Device Code. The indi-
– 6 –
By Sear c hing Thr ough the Librar y
If you cannot identify a correct Device Code for your equipment from the Device
Code list, you may search for the code in the library:-
1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g.
3. Hold down " CH+ " and " VOL– " on the URC simultaneously for 2 seconds
until the indicator lights up.
4. Enter a corresponding Magic Search Code from the following table. The
indicator should go out immediately.
DEVICE TYPE:
MAGIC SEARCH CODE: 0001 0002 0003 0005
(e.g. press
enter TV Magic Search Code 0001.)
5. Press the same desired device mode key again as in step 2 above. (e.g.
6. Hold down " CH+ " & " VOL– " simultaneously for 2 seconds until the
indicator lights up, and your URC is ready to start searching.
7. Aim the URC at your device (e.g. TV), press the "
repeatedly until the device has been turned off.
Once
your
é
é
Key (e.g.
TV
* Simply repeat the above setup procedures to search for the Device Code for
your SAT or DVD. (Remember to press the correct Device Mode Key and
correct Magic Search Code in step 2-5 above)
IMPORTANT:
– If the power on/off function of your device is not infra-red controlled, you
need to follow steps 2 to 6 above and start searching :-
•
Press "
" and another function key alternately until your device responds
to the expected function, then press " CH+ " and " VOL– " to lock in the
code.
e.g. Press "
Press "
Note:
– DVD and other device codes can be searched for and locked into any
device modes except "TV" & "SAT" modes. Simply press the corresponding
device mode key in step 2 & 5 and enter an appropriate Magic Search
Code for your DVD and other devices.
– Each time you press the "
send out a POWER signal trying to turn off your device.
If you fail to stop pressing "
turned off, turn your device on again immediately. Before the indicator
goes out, press "
and lock in the code.
– If the indicator flashes twice after your pressing of "
2
HOW
already at the last code of the library. Press " CH+ " and " VOL– " to resume
the URC and repeat the above procedures carefully to search again.
).
TV
TV VCR SAT DVD
device mode key, then press " CH+ " and " VOL– " , and
TV
device
has
been
turned
off,
immediately
é
é
é
é
é
) to lock in code and the indicator should go out.
" & " 1 " alternately, or ;
" & "
" alternately.
", the URC will skip to the next code and
" in time when your device has been
" on the URC to skip backward. Repeat step 7 above
– 7 –
GB
)
TV
" key slowly and
press
Device Mode
é
é
" key, you are
Werbung
Inhaltsverzeichnis
