Inhaltsverzeichnis
Werbung
Technical data
Blows per minute
Chisel rivet set shank (")
Chisel rivet set shank (mm)
Weight (kg)
Weight (lb)
Noise and vibration
Sound pressure
level (dB(A))
CP9361 79
Declarations
Noise and vibration
Uncertainty 3 dB(A), in accordance with EN ISO 15744. For
Sound power level, add 11 dB(A)
Vibration standard : ISO-28927-9
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, CHICAGO PNEUMATIC Tool Co. LLC, cannot be
held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
4
CP9361
13500
0.125
3
0.14
0.31
Vibra-
Vibration uncer-
tion (m/s²)
tainty
5.1
2.4
http://
and selecting 'Tools' then 'Legis-
© Chicago Pneumatic - P145929
EU DECLARATION OF CONFORMITY
We, CHICAGO PNEUMATIC Tool Co. LLC, 1815 Club-
house Road, Rock Hill, SC 29730, declare under our sole re-
sponsibility that the product (with name, type and serial
number, see front page) is in conformity with the following
Directive(s):
2006/42/EC
Harmonized standards applied:
EN ISO 11148-4 : 2012
Authorities can request relevant technical information from:
Pascal Roussy, R&D Manager, Ets Georges Renault, 38 rue
Bobby Sands, BP10273 44818 Saint Herblain, France
Saint-Herblain,
Pascal ROUSSY
Signature of issuer
Statement of use
This product is designed for chipping, riveting, scaling, or
ramming, according to its operating instructions. No other
use permitted. For professional use only.
Operation
See figures on page 2.
• Fix the accessories properly to the tool.
• Connect device to a clean and dry air supply.
• See figure 02 to operate the tool.
Maintenance instructions
• Follow local country environmental regulations for
safe handling and disposal of all components.
• Maintenance and repair work must be carried out by
qualified personnel using only original spare parts. Con-
tact the manufacturer or your nearest authorised dealer
for advice on technical service or if you require spare
parts.
• Always ensure that the machine is disconnected from en-
ergy source to avoid accidental operation.
• Disassemble and inspect the tool every three 3 months if
the tool is used every day. Replace damaged or worn
parts.
• To keep downtime to a minimum, the following service
kit is recommended : Tune-up kit
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
(2) drops per minute.
Engraving Pen
Werbung
Inhaltsverzeichnis
