PALLADIOM SMC5500050407 Konfigurationsanleitung

P/N 041563 Rev. D
04/2018
Configuration Instructions
Please read before installation.
The FCU controller (model numbers: SMC5500050407, SMC5300020401, FCABACPSS002, SMC55-HOSP, SMC53-HOSP) must be correctly
configured for the HVAC System. The Palladiom thermostat is used to configure the FCU controller. The thermostat must be connected to the FCU
controller and both must be powered to set a configuration.
Step 1: Determine the Basic Configuration for the System
Determine the basic configuration number of your system using the table below.
System Configuration
(Pipe Configuration)
As-Is
• 4 -pipe
• 2 -pipe cooling with resistive
heating element
• 2 -pipe heating only
• 2 -pipe cooling only
• 2 -pipe with a changeover sensor
* For Floating Point Valves, choose On/Off Relays, then see Advanced Configuration parameters 60 and 61 on page 2. Also, see Application Note #630 (P/N 048630) at www.lutron.com
** Simultaneous 0 – 10 V- and relay controls available in SMC55-HOSP version 5010 or later and SMC5500050407 version 5008 or later.
Step 2: Set the Basic Configuration
Configure the basic configuration you selected in Step 1 by following the steps below:
Enter Basic Configuration Mode:
• I f the thermostat has been powered for over 15 minutes, cycle power to the
thermostat. This can be done by removing power with the thermostat's circuit breaker
or by carefully pulling the thermostat from the adapter by hand and removing the
4-wire harness from the back of the thermostat. The previously saved settings are
stored during power cycles.
• H old the °C | °F and buttons for 3 seconds. Once the display begins to flash,
release both buttons and hold only the °C | °F button for 3 seconds.
• T he thermostat will enter the Basic Configuration Mode (
one circle filled in on the display.
Set the Basic Configuration:
• O nce in the Basic Configuration Mode, tap the } or { buttons to display the desired
configuration number. Only the supported options are displayed.
• H old the u button for 3 seconds to save this configuration. The display will flash,
then normal operation will begin.
Step 3: Set the Advanced Configuration (Optional)
Review the Advanced Configuration Parameters Table on the next page. If any values
need to be changed, enter Advanced Configuration Mode using the steps below. To enter
Advanced Configuration Mode, you must have already saved a basic configuration and
exited to the normal operating mode.
Enter Advanced Configuration Mode:
• I f the thermostat has been powered for over 15 minutes, cycle power to the thermostat.
Your previously saved settings are stored during power cycles.
• H old the °C | °F and buttons for 3 seconds. Once the display begins to flash,
release both buttons and hold only the
• T he thermostat will enter the Advanced Configuration Mode's Parameter Menu (
"P", "Set", and 2 circles filled on the display.
Select a Parameter to Modify:
• Tap the } or { buttons to change parameter identification number.
• Tap the u button to select the parameter.
• T he thermostat will enter the Parameter Value Selection Menu (
the display.
Set or View a Parameter Value:
• W hile in the Parameter Value Selection Menu (
the desired value for the parameter.
• O nce the correct value is displayed, tap the u button to set this value. The Set segment
will show and the display will return to the Parameter Menu
• I f you do not want to set a new value, tap the
• Follow the steps above to set all the parameters required for your system.
• W hen finished, hold the u button for 3 seconds. The display will flash and return to
normal operation.
Customer Assistance - 1.844.LUTRON1 (U.S.A./Canada) or +44.(0)20.7680.4481 (Europe)
Valve/Element Control Fan Control
(Valve Type) (Fan Type)
Use current configuration on the controller
H/M/L Relays
Two On/Off relays*
0–10 V- Signal
Two 0–10 V- signals or H/M/L Relays
one relay and one
0–10 V- Signal
0–10 V-**
H/M/L Relays
One On/Off relay*
0–10 V- Signal
H/M/L Relays
One 0–10 V- signal
0–10 V- Signal
1 2 3
), with "Set" and
button for 3 seconds.
1 2 3
), with 3 circles filled on
1 2 3
), tap the } or { buttons to change
1 2 3
.
button to return to the Parameter Menu.
Thermostat and Fan Coil
2-pipe/Single Thermal
Type (2-pipe mode)
—
—
—
—
Changeover Sensor
Heat-only
Cool-only
Changeover Sensor
Heat-only
Cool-only
Changeover Sensor
Heat-only
Cool-only
Changeover Sensor
Heat-only
Cool-only
Diagram 1: Basic Configuration Mode
1 2 3
Hold 3
seconds to
save and exit
configuration
mode
Diagram 2: Advanced Configuration Mode
Tap to view
parameter value,
Hold 3 seconds
to save and exit
T p to view
configuration
parameter value
mode
Hold 3 seconds
to save and exit
1 2 3
), with
Diagram 3: Advanced Configuration Mode
1 2 3
Tap to set and
return to
Parameter Menu,
Hold 3 seconds to
save and exit
mode
Tap to set and
return to
Return to
Parameter Menu
Parameter
without setting
Menu, Hold 3
seconds to
save and exit
configuration
mode
Unit (FCU) Controller
Basic Configuration Supported
Basic
Models
Configuration
Number
SMC53x FCAx
00
 
01
 
02
03
04
05
 
06
 
07
 
08
09
10
11
12
13
14
15
16
Set
C F
LUTRON
Hold °C | °F and for 3 seconds,
.
then °C | °F for 3 seconds to enter mode.
Parameter Menu
Advanced Configuration Mode
Parameter Menu
Set
C F
LUTRON
Hold °C | °F and for 3 seconds, then for 2 seconds to enter mode.
Hold °C | °F and for 3 seconds,
then for 3 seconds to enter mode.
Parameter Value Selection Advanced Configuration Mode
Parameter Value Selection
C F
LUTRON
Return to Parameter
Menu without setting
www.lutron.com/support
English
SMC55x

















Increase
Decrease
1 2 3
Increase
Decrease
Increment
Increase
Decrement
Decrease