Seite 1
TPC-1570H Intel Celeron M Touch Panel Computer with high luminance 15" XGA TFT LCD User Manual...
Seite 2
Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Part No. 2003157000 1st Edition Printed in Taiwan March 2006 TPC-1570H User Manual...
Seite 3
Product Warranty (1 year) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper instal- lation.
Seite 4
- Product name and serial number - Description of your peripheral attachments - Description of your software (operating system, version, appli- cation software, etc.) - A complete description of the problem - The exact wording of any error messages TPC-1570H User Manual...
Seite 5
Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. • 1 x TPC-1570H-A1,or 1 x TPC-1570H-B1 • 8 x Panel mounting clampers • 8 x Panel mounting screws •...
Seite 6
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Ver- wenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. Das Gerät ist vor Feuchtigkeit zu schützen. TPC-1570H User Manual...
Seite 7
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBw- erte.
Seite 8
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder weiger. Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab. TPC-1570H User Manual viii...
BIOS: Award 4Mbit flash memory South Bridge: Intel 855GME/ 852GM GMCH/ICH4 chipset VGA: Intel 855GME for TPC-1570H-A series; Intel 852GM for TPC- 1570H-B series; Support 16 MB frame buffer with system memory; Simultaneously support of CRT and LVDS flat panel display.
Such phenomenon is claimed to be normal accord- ing to the LCD manufacturers. 1.4 Touchscreen Specifications Resistive Touchscreen Type Tempered Glass Base Glass Construction 1024 x 1024 Resolution 75% typical Light Transmission RS232 Interface Controller 3.3 to 5V Power Rating 100 million touches Durability TPC-1570H User Manual...
Make sure the waterproof gasket is in position before install- ing the TPC-1570H to the panel opening. 2. Install the TPC-1570H to the panel opening. 3. Find out the eight clampers and eight long screws in the acces- sory pack.
1.9 Dimensions and cutout Weight: 5.5 Kg (without HDD) Dimensions: 383 x 307 x 65mm (WxHxD) Cutout: 373.5 x 297.5 mm (suggested) Figure 1.4: Dimensions Chapter 1...
Chapter 2 System Setup This chapter provides a brief explanation for operating the TPC-1570H. It is easy to make the TPC-1570H start working with the below step-by- step. Step 1: Unpack the TPC-1570H package. Please check the packing list at the beginning of this manual.
Seite 23
Figure 2.2: Install CompactFlash memory card Warning It is suggested to turn OFF system power as plug in or pull out the memory card, though the Compact- Flash memory is supposed to be hot swappable. Step 3: Connect the power connector to the 24VDC power lines. The power lines can either be of some power adapter or in-house power source.
Seite 24
Step 5: Push the power button to power on the system as the figure 2.4. Step 6: Calibrate the touchscreen. Please go to “Start” ”Programs” ”PenMount DMC9000 Utilities”->”Control Panel” as the figure 2.5. Then, click the tab “Calibrate” to calibrate by selecting the standard calibration or advanced calibration. TPC-1570H User Manual...
Seite 25
If your operating system is Windows CE, the details of the procedure are described in following section. Figure 2.5: Touchscreen Calibration - 1 Figure 2.6: Touchscreen Calibration - 2 Chapter 2...
Serial port:COM1 RS232 COM3 COM3 Serial port:COM3 RS232 COM4 COM4 Serial port:COM4 RS232/422/485 COM4 MODE1 Setting COM4 RS232/422/485 mode COM4 MODE2 Setting COM4 RS422 Master or Slave mode CLEAR CMOS CLEAR CMOS POWER SWITCH System Power Switch TPC-1570H User Manual...
Seite 29
Figure 3.1: Main Board Connector -1 Figure 3.2: Main Board Connector -2 Chapter 3...
Chapter 4 Software Configuration A support CD-ROM for TPC-1570H is available and along with the prod- uct. There are related utilities and drivers for TPC-1570H included. Please install the Chipset INF driver, VGA graphics driver, LAN driver, audio driver, Advantech.com driver, Touchscreen driver and Watchdog Timer (WDT) driver sequentially.
4.1.4 Audio Driver Path: \ audio\ Available for the OS’s below: • Microsoft Windows 98 SE • Microsoft Windows 2000 • Microsoft Windows XP 4.1.5 Advantech COM Driver Path: \ Advantech com \ Available for the OS’s below: • Microsoft Windows 98 SE •...
A com port named COM3 or COM4 on TPC-1570 is Advantech Special com port. Please follow the steps below to install the driver. Step 1: Insert the companion CD-ROM into your CD-ROM drive. Open the directory: \ advantech com\ TPC-1570H User Manual...
Seite 35
Step 2: Use Windows Explorer (or Windows Run command) to execute PCI_ICOM.EXE from the companion CD-ROM. Step 3: Click Next to continue installation. Chapter 4...
Seite 36
Step 4: Click Next to continue installation. TPC-1570H User Manual...
Seite 37
Step 5: Click uninstall icon to remove ?PCI Serial Port Chapter 4...
Seite 38
Step 6: Click the scan for hardware changes icon to remove ?PCI Serial Port TPC-1570H User Manual...
Seite 40
Step 7: Found New Hardware and Click Next to continue installation. Step 8: Click Finish the Advantech PCI Serial Port to continue. TPC-1570H User Manual...
Seite 41
Step 9: Then, found New Hardware and Click Next to continue. Step 10: Click Finish the Advantech PCI-1602 Serial SlaveBridge to continue installation. Chapter 4...
Seite 42
Step 11: Found New Hardware and Click Next to continue installation. TPC-1570H User Manual...
Seite 43
Step 12: Click Finish the Advantech PCI Serial Port to continue. Chapter 4...
4.3 Watchdog Timer (WDT) Driver Installation In order to ensure reliable and fail-safe performance, TPC-1570H has a built-in Watchdog Timer to handle unexpected system failures. TPC- 1570H provides the drivers and a utility to activate and configure the timer for Windows2000/XP operating systems. The following is a brief introduction, using Windows2000 as an example, for the installation and configuration procedures.
4.3.1 Installing the TPC-1570 Watchdog Timer Driver Step 1: Insert the companion CD-ROM into your CD-ROM drive. Open the directory: \WDT\8362x\W2K_XP. Step 2: Use Windows Explorer (or Windows Run command) to execute SETUP.EXE from the companion CD-ROM. Chapter 4...
Seite 46
Step 3: Click Next to proceed. TPC-1570H User Manual...
Seite 47
Step 4: Click Next to confirm the customer information. Step 5: Select Advantech [W83627HF] Watchdog Timer and click Next. Chapter 4...
Seite 48
Step 6: Click Next to confirm selecting the Typical setup type. Step 7: Click Next to proceed. TPC-1570H User Manual...
Seite 49
Step 8: Click Finish to complete the procedure. Step 9: Click OK to restart the system and activate the Watchdog Timer. Chapter 4...
4.3.2 How to Use the TPC-1570H Watchdog Timer Step 1: Open the Control Panel and click Watchdog Service Configuration. Step 2: Click the Start Service button. TPC-1570H User Manual...
Seite 51
Step 3: Click Setting to select the setting page. Step 4: Select the Timer Span that meets your application requirement. Chapter 4...
Seite 52
Step 6: Check the Start watchdog service on boot to enable the Watchdog timer to start automatically after the system boots every time. Step 7: Click OK, then the configuration procedure is finished. Note Use advantech WDT Driver.WDT was enable,and WDT LED was 1Hz glisten. TPC-1570H User Manual...
4.4 Dual Display Setting If you use CRT monitor, you must Connections to CRT port in during system boot up. During system boot up, the system will set CRT parame- ter. If you have multiple devices, you can set them. Step 1: click Intel graphic icon from the toolbars Step 2: select Graphics Options ->...
Chapter 5 Windows XP Embedded TPC-1570H is in support of embedded windows platform. This section is to state the important features, EWF and HORN, provided in windows XP embedded. 5.1 EWF EWF stands for Enhanced Write Filter. It provides an upper filter in the storage device driver stack that redirects disk write operations to volatile (RAM) or non-volatile (disk) storage.
In other words, the hibernation file is 512MB that is the same as memory size used on TPC-1570H-A1 or TPC-1570H-B1. 5.3 Advantech Utilities TPC-1570H provides the useful utilities for users to configure the HORM and EWF. 5.3.1 Version Information Start menu->...
Please follow the steps before running this utility to create full HORM environment. Enable Hibernation via Power Options in Control Panel Make C: partition EWF-enabled via OSLock Make sure that all volumes to be dismounted are not in use. TPC-1570H User Manual...
NRTS NCTS A.2 COM4 Setting The serial port COM4 on the TPC-1570H is adjustable. It can be set to RS-232, RS-422 or RS-485. This port is designed with auto data flow control capability. In other word, the TPC-1570H can automatically detect the data flow direction at this port when the two wired RS-485 communication is activated.
Appendix B Watchdog Timer on WinCE There is a built-in Watchdog timer on Windows CE 5.0 for TPC-1570H. You can access it through WIN32 API. TPC-1570H provides a WDT driver to allow users to enable/disable the Watchdog timer. The driver name is “WDT1:”.
Seite 65
control codes can then be advertised, and an application can use these control codes with DeviceIoControl to perform driverspecific functions. lpInBuffer [in] Long pointer to a buffer that contains the data required to perform the operation. This parameter can be NULL if the dwIoControlCode parame- ter specifies an operation that does not require input data.
WDT driver, your application must trigger the Watchdog once during the Watchdog timer period. If your application has not triggered at the specified period, the device will reboot automatically. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: unused. nOutBufferSize: unused. TPC-1570H User Manual...
Seite 67
IOCTL_WDT_GETTIMEOUT: Gets the Watchdog time setting. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD pointer to your Watchdog time setting. The Watchdog time setting is just a number. 0 means 2 seconds, 1 means 5 seconds, 2 means 10 seconds, 3 means 15 seconds, 4 means 30 seconds, 5 means 45 seconds and 6 means 60 seconds.
// assign the WDT driver name wsprintf(szClassName, TEXT("WDT1:")); // Open the WDT driver m_hWDT = CreateFile(szClassName, GENERIC_READ GENERIC_WRITE, 0, NULL, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL, NULL); if ( m_hWDT == INVALID_HANDLE_VALUE ) { DebugMsg(CString("WDT driver fail")); return; DWORD dwTemp; DWORD nIndex=2; TPC-1570H User Manual...
Seite 69
// Set the Watchdog Timer as 10 seconds. Number 2 means 10 seconds. DeviceIoControl(m_hWDT, IOCTL_WDT_SET_TIMEOUT, &nIndex, sizeof(nIndex), NULL, 0, &dwTemp, NULL); // Enable the Watchdog timer DeviceIoControl(m_hWDT, IOCTL_WDT_ENABLE, NULL, 0, NULL, 0, &dwTemp, NULL); While (1) { // do your job here. Sleep(8000);...
Appendix C Watchdog Timer Programming C.1 Overview The TPC-1570H cards’ watchdog timer can be used to monitor system software operation and take corrective action if the software fails to func- tion after the programmed period. This section describes the operation of the watchdog timer, and how to program it.
C.2 Watchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. You must first assign the address of register by writing address value into address port 2E(hex), then write/read data to/from the assigned register through data port 2F (hex).
0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is "time out". AA (hex) ----- Write this address to I/O port 2E (hex) to lock the watchdog timer.2 TPC-1570H Series User Manual...
C.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;----------------------------------------------------------- Mov dx,2eh ; Unlock W83627HF Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ;...
Seite 76
Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Set minute as counting unit Mov al,0f5h TPC-1570H Series User Manual...
Seite 77
Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;----------------------------------------------------------- Dec dx ; Set timeout interval as 5 minutes and start counting Mov al,0f6h Out dx,al Inc dx Mov al,5 Out dx,al ;----------------------------------------------------------- Dec dx ; lock W83627HF Mov al,0aah Out dx,al 3.
Seite 78
4. Enable watchdog timer to be reset by keyboard ;----------------------------------------------------------- Mov dx,2eh ; unlock W83627H Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------- TPC-1570H Series User Manual...
Seite 79
Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------------------------------------------- Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al ;-----------------------------------------------------------...
Seite 80
Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------- Dec dx ; lock W83627HF Mov al,0aah Out dx,al TPC-1570H Series User Manual...
Seite 81
Accessory Kit Assembly This appendix shows how to connect to a CD-ROM via the CompactFlash slot.:...
Please follow this assembly procedure to use the CompactFlash slot to connect with a CD-ROM drive. Connect the IDE cable to the adapter board. Figure D.1: Adapter Board and IDE Cable Figure D.2: Connecting Adapter Board & IDE Cable TPC-1570H User Manual...
Note Pin 1 is marked red Insert the adapter board into the CompactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.5: Inserted Adapter Board Appendix D...
Note Please make sure Windows 2000 Service Pack 4 is installed before you install the USB 2.0 driver on Windows 2000. Service Pack 1 must be installed on Windows XP before you install the USB 2.0 driver. TPC-1570H User Manual...
Please follow the assembly procedure to install the HDD into the system. Remove the rear cover. Figure E.1: Removing the Rear Cover De-assemble the HDD kit from the system. Please remove the two screws and take the transparent rubber cushion off.. Figure E.2: Removing the Top Screws TPC-1570H User Manual...
Link the HDD with the HDD cable connector and fasten the HDD module with the screws. Figure E.7: Linking the HDD with the Connector Fasten the HDD cover with screws Figure E.8: Fastening the HDD cover Appendix E...
Place the HDD kit into the system: Align to the HDD chamfer as shown the below in red circle and then slide the HDD module into the system sideways. Figure E.9: Chamfer Figure E.10: Chamfer & Rubber TPC-1570H User Manual...
Mount the two rubber cushions on the HDD kit and fasten the HDD kit with the system by screws Figure E.13: Mounting the Rubber Cushions Figure E.14: Fastening the HDD Module TPC-1570H User Manual...
Seite 95
Touchscreen Installation & Configuration This appedix demonstrates how to install the PenMount 9000 touchscreen and set the configuration on TPC- 1260H. This section uses Windows XP as an example.
Configuration F.1 Driver Installation Please insert the x86 TPC series support CD and go to the Windows 2000-XP driver folder (TPC-1570H\Driver\Touch Screen\Driver\Win- dows 2000-XP Driver V4.01). Click setup.exe Figure F.1: Setup.exe The screen displays the installation wizard for the PenMount software.
F.2 Uninstall the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Programs. Figure F.5: Uninstall -1 Select PenMount DMC9000 and DMC9100. Click Remove button. Figure F.6: Uninstall -2 TPC-1570H User Manual...
Mount Control Panel. It contains six functions: Calibrate, Draw, Multiple Monitors, Option, and About. Multiple Monitors is for multiple displays only; however TPC-1570H only provides one touchscreen display. This function is not workable on TPC-1570H. About is to show the driver ver- sion. Calibrate Two ways to calibrate the touch screen include “Standard Calibration”...
Figure F.10: Standard Calibration -3 Note Touch the red squares in sequence. The cali- bration is completed after the fifth touch red point is calibrated. Press “ESC” to skip. Advanced Calibration is for the aged touchscreens by using 4, 9, 16 or 25 points to calibrate touch panel.
Figure F.13: Plot Calibration Data Note Plot Calibration Data enabled provides the blue lines to show linearity before calibration and black lines to show linearity after calibration when you finished the advanced calibration. Draw This is to test the touch screen operation. Its display shows touch loca- tion.
Option This option is to set the operation mode and beep sounds if the beep sound is enabled. The operation mode, stream mode and point mode, is to enable/ disable the mouse’s ability to drag on-screen icons. Stream mode let the mouse functions as normal and dragging on-screen. Point mode is only let the mouse a click function.
Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse cover back in position Figure G.1: Fuse Replacement Warning Do NOT replace the fuse unless it is damaged. Do NOT replace the fuse with a different rating. TPC-1570H User Manual...