Measupro CC200 Bedienungsanleitung

Wireless Cycle Computer and Heart Rate Monitor
Product Manual
CC200
Overview
Thank you for purchasing the MeasuPro Wireless Cycle Computer and Heart
Rate Monitor. This product will help you monitor your heart rate along with
distance, speed, riding time, and calories burned while biking. This will help
you keep an accurate record of your workout stats. Please read the instruction
manual thoroughly before use. Please store the manual for future reference.
Main Features
• Time Display: hour, minute and second, support 12/24 display format.
• Bike Computer Functions: displays current speed, average speed, max.
speed and speed tendency
• Heart Rate Monitor Functions: displays current heart rate, average heart rate,
max. heart rate and heart rate tendency, 4 sets high/low heart rate alarms
• Heart Rate Monitor with 5.3K Wireless Analog Transmission
• Riding Data Display: displays riding time, total riding time, riding distance,
total distance and calorie
Specification Range
Speed: 0-150 Km/h 93.2 Mile/h
Heart Beat: 30 bpm - 240 bpm
Riding Distance(DST): 0-999.9 km/mile
Total Riding Distance(ODO): 0-999.9 km/mile Riding Time(RTM)0-99:59:59
Total Riding Time(TTM): 0-99999 H
Calorie: 0.0-999.9 Kal
Age: 10-65 (Default:20)
Weight: 10-150 Kg or 22-330 lb (Default 65 kg)
Gender: Male/Female (Default M)
Installation Instructions
Battery Installation
Speed: 0-150 km/h or 93.2 Mile/h
Use a coin to twist the battery door counter-clockwise to open it. Insert the
new battery 1 x CR2032 with the positive side facing up. Use a coin to twist
the cover back.
Sensor Installation
Install the magnet sensor on the bicycle front fork on the same side as the
magnet. Magnet can be attached with spacer and fix it on the bicycle front fork
with the nylon cable tie. See illustration above. Adjust the distance between the
magnet and the sensor to 2-5mm.
Bike Computer Installation
• Use cable ties to fix the base on the handlebars. Rubber pad can be used
between the base and handlebar.
• Align unit with the base and turn clockwise to fasten; vice versa when
detaching the unit.
• Check installation conditions: check the unit if the bicycle symbol is displayed.
If signal does not appear readjust the position of magnet and sensor.
Initialization Settings
• When the unit is powered on for the first time
all figures will be displayed on the LCD. After 2
seconds, the unit will enter the settings mode.
• To reset settings at any time press and hold both
buttons simultaneously for 3-5 seconds.
• Press K1 to change setting items on the following
order.
• Press K2 for increment setting. Hold K2 for 2
seconds for fast incremental settings.
Using the Heart Rate Monitor
1. Remove any insulation strips that have been
placed in the battery compartment located on
the back of the heart rate monitor.
2. Wet the electrode area of the transmitter before
placing the strap on your chest. This will ensure
the best electrical connecting and reliable
operation.
3. Position the heart rate monitor on your chest as
shown in the diagram on the right.
Operation Modes
Press K1 to switch the modes in the following order:
Time Mode  Riding Time Mode  Total Riding Time Mode  Riding Distance
Mode  Total Riding Distance Mode  Calories Burned Mode
Time Mode
Main functions:
• Displays hour, minute, 12/24h format
• Displays current speed, max. speed and average riding speed
• Displays current heart rate, maximum heart rate, minimum heart rate and
average heart rate.
• When the heart rate alarm is turned on, there will be "bi...bi..." alert if the user's
heart rate is beyond the setting range.
• The heart rate display will automatically switch the heart rate in the following
order every 3 seconds: maximum heart rate  minimum heart rate  average
heart rate  current heart rate.
Display instruction:
• First line: display current riding speed (or max. speed, average
speed)
• Second line: display current heart rate, maximum heart rate,
minimum heart rate and average heart rate.
• Third line: display hour, minute.
Time setting:
• When stop riding, press K1 for 3 seconds to enter the time setting mode, the
item being set flashes.
• Press K1 to switch the item being set in the following order: 12/24 hour
format  hour  minute  second  confirm and back to the time display
mode.
• When setting an item, press K2 key for increment settings, hold K2 for fast
incremental settings.