Seite 1
OPERATING INSTRUCTIONS FOR COMARK C9500 SERIES INTRINSICALLY SAFE PRESSURE METERS ENGLISH DEUTSCH FRANCAIS ITALIANO ESPANOL For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
OPERATING INSTRUCTIONS FOR COMARK C9500 SERIES INTRINSICALLY SAFE PRESSURE METERS GENERAL INFORMATION These instruments have been certifi ed by Baseefa 2001 Limited and are suitable for use in accordance with the marks which have been applied. The marks are described in Clause 28 of EN 50014.
Seite 7
Declarations of Conformity available. Contact Comark Customer Support or your local Distributor. In line with its policy of continuous development, Comark Instruments reserves the right to alter the instrument specifi cation without prior notice. Further information is available from Comark Instruments or your distributor.
The Comark UKAS (United Kingdom Accreditation Service) accredited temperature calibration laboratory is one of the fi nest in the UK. Comark UKAS certifi cates can offer the lowest uncertainty of 0.01°C and provide independent proof of correct calibration using equipment and procedures audited by UKAS inspectors.
Seite 9
Service/Repairs Regular servicing and any required repairs, under warranty or after, are available from the Comark Service Department. For more information on all Comark certifi cation, calibration and service facilities please call Comark Customer Support or contact your local distributor.
INTRODUCTION The C9500 Series IS pressure meters includes:- C9501/IS Range 0 to ±2 PSI / 0 to ±140mbar Differential C9503/IS Range 0 to ±5 PSI / 0 to ±350mbar Differential C9505/IS Range 0 to ±30 PSI / 0 to ±2000mbar Differential C9507/IS Range 0 to ±100 PSI / 0 to ±6900mbar Differential...
KEY FUNCTIONS ON/OFF Key Press once to switch on the instrument. Repeat to switch off. Holding down the key when switching on will display the maximum pressure range of the instrument in PSI. Holding down the key when switching off will display all segments as a test.
RECORD Key Press once to put the instrument into record mode. This will be indicated by the word RECORD on the display. Maximum and minimum pressure readings can be stored and displayed while the instrument is in record mode. When the instrument is in record mode, press key once to display the current maximum reading and press again to display the current minimum reading.
CONNECTION TO PRESSURE SOURCES The C9500 Series IS instruments are fi tted with " BSP female connectors. The following checks must be made before connecting the instrument to a pressure source:- Check the security of all fi ttings. Check that the pressure source does not exceed the ratings for the instrument as set out in Table 1.
(5th) digit, whilst continuing with correct values of the lower 4 digits. Differential or Gauge Measurement C9500 series instruments can be used in either a gauge or differential pressure measurement system. Gauge: For positive gauge measurements the negative...
Use with Pressure Test Kit The C9500 series instruments can be used together with the optional TK2 pressure test kit as a low cost calibration system for checking or calibrating other pressure instruments.
SPECIFICATION C9501/IS C9503/IS C9505/IS C9507/IS Range 0 to ±2 0 to ±5 0 to ±30 0 to ±100 Resolution 0.001 0.001 0.01 mBar Range 0 to ±140 0 to ±350 0 to ±2000 0 to ±6900 Resolution Range 0 to ±55 0 to ±140 0 to ±830 0 to ±2750 Resolution...
Seite 17
POWER SOURCE 9V PP3 6F22 — MN1604 UCAR9V BATTERY LIFE 125 hours (using MN1604) LOW BAT CHECK Displays BAT just before end point of battery OVER PRESSURE – – – – INDICATION OVER 9999 Lowest 4 digits blink READING INDICATION CONNECTIONS "...
EIGENSICHERE DRUCKMESSGERÄTE DER SERIE C9500 ALLGEMEINE INFORMATIONEN Diese Geräte wurden nach den Baseefa 2001 Limited zugelassen und eignen sich für den Einsatz entsprechend der Marken, mit denen sie geliefert wurden. Diese Marken sind in Klausel 28 von EN 50014. WARNUNG Dieses Gerät ist für die nachstehende Klasse zugelassen: II 1 G EEx ia IIC T4...
Seite 19
Comark Kundenservice oder vom lokalen Vertriebspartner. Entsprechend dem Geschäftsgrundsatz einer dauernden Weiterentwicklung behält sich Comark Instruments das Recht vor, die technischen Daten des Geräts ohne vorherige Notiz zu ändern. Weitere Informationen stehen von Comark Instruments oder Ihrem Händler zur Verfügung.
Verfahren erstellt, die die Produkteigenschaften mit den jeweiligen nationalen Normen vergleichen. Um den sorgenfreien Betrieb sicherzustellen und die Vorschriften zu beachten, empfi ehlt Comark eine jährliche Zertifi zierung und Neukalibrierung. Zwei Zertifi kat-Klassen sind für Infrarot-Temperaturmessgeräte und Nicht-Temperaturmessgeräte sowie Feuchtemeggeräte lieferbar:...
Zertifi zierung nach NPL-Standards Comark sind NPL Bescheinigungen auffundbar zum Nationalen Physischen Labor und können Ungewißheit so niedrig wie 0.3°C anbieten. Konformität Konformitätszertifi kate können für neue, gewartete und neu kalibrierte Instrumente vorgelegt werden. Diese Zertifi kate bestätigen, dass die Geräte ihren ursprünglichen Herstellerspezifi...
EINFÜHRUNG Die Baureihe C9500 IS umfaßt: C9501/IS Bereich 0 bis ±2 PSI/0 bis ±140mbar Differenzmessung C9503/IS Bereich 0 bis ±5 PSI/0 bis ±350mbar Differenzmessung C9505/IS Bereich 0 bis ±30 PSI/0 bis ±2000mbar Differenzmessung C9507/IS Bereich 0 bis ±100 PSI/0 bis ±6900mbar Differenzmessung For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
TASTENFUNKTIONEN Taste EIN/AUS (ON/OFF) Einmal drücken, um das Gerät einzuschalten. Durch erneutes Drücken wird das Gerät wieder ausgeschaltet. Wird die Taste beim Einschalten gedrückt, erscheint auf der Anzeige der max. Druckbereich des Geräts in PSI. Wird die Taste beim Ausschalten gedrückt, werden alle Display-segmente aktiviert (Displaytest).
Taste FILTER (FILT) Diese Taste drücken, um unbeständige Meßwerte zu fi ltern. In Betriebsart Filtern berechnet das Gerät den Durchschnitt der in den letzten 4 s aufgenommenen Meßwerte (16 Meßwerte), um eine stabile Anzeige zu erreichen. Ein erneutes Drücken der Taste leitet wieder den normalen Betrieb ein.
Es ist zu prüfen, daß die zu messenden Gase rostfreien Stahl, Glas, Keramik, Silikon, Nickel, Aluminium, Gold und Epoxydharz weder beschädigen noch korrodieren. Hinweis: Die Comark-Druckmeßwertgeräte der Baureihe C9500 IS sind nicht für absolute Druckmessungen ge-eignet. Hinweis: Es dürfen an keinen Eingang Drücke angelegt werden, die unter Berücksichtigung des...
WEITERE FUNKTIONEN Niedriger Ladezustand der Batterie Das Symbol BAT auf der Anzeige läßt den niedrigen Ladezustand der Batterie erkennen. Nach Erscheinen dieses Symbols ist die Batterie sobald wie möglich auszutauschen. Druck außerhalb des Bereichs Wenn der gemessene Druck (Über- oder Unterdruck) den Bereich des Geräts überschreitet, lautet die Anzeige - - - -.
Auswechseln der Batterie Lösen Sie die Inbusschrauben an der Unterseite des Meßgerätes und ziehen Sie die Batteriekappe ab. Ersetzen Sie die Batterie durch eine neue Batterie Typ 9 Volt PP3 wie im Batteriefach oder der Bedienungsanleitung angegeben. Schrauben Sie die Batteriekappe wieder auf und achten Sie darauf, daß...
TECHNISCHE DATEN C9501/IS C9503/IS C9505/IS C9507/IS Messbereiche 0 bis ±2 0 bis ±5 0 bis ±30 0 bis ±100 Aufl ösung 0,001 0,001 0,01 mBar Messbereiche 0 bis ±140 0 bis ±350 0 bis ±2000 0 bis ±6900 Aufl ösung Messbereiche 0 bis ±55 0 bis ±140 0 bis ±830 0 bis ±2750 Aufl...
Seite 29
BATTERIE- 125 Stunden LEBENSDAUER (bei Verwendung von MN1604) PRÜFUNG AUF Anzeige von BAT kurz vor Ende der UNGENÜGENDE Batterielebensdauer BATTERIELADUNG ANZEIGE VON – – – – BEREICHSÜBER- SCHREITUNG UBERLAUF- Niedrigste 4 Stellen blinken ANZEIGE 9999 ANSCHLÜSSE " BSP Buchse GEWICHT 330g inklusive Batterie Geprüft zu EN 61326-1 Kriterien B Leistung...
MANOMETRES A SECURITE INTRINSEQUE SERIE C9500 GENERALITES Ces instruments ont été homologués par dans les atmosphères Baseefa Limited et sont aptes à l’usage conformément aux marquages qui ont été appliqués. Les marquages sont décrits dans l’Annexe 28 de EN50014. ATTENTION L’homologation de cet instrument est désignée par: II 1 G EEx ia IIC T4 Baseefa 03 ATEX 0079...
Seite 31
Compatibilité Electro-magnétique, EN 61326-1. La Déclaration de Conformité est disponible auprès du service commercial de Comark ou bien auprès du distributeur local. Conformément à sa politique de développement permanent, Comark Instruments se réserve le droit de modifi er sa spécifi cation sans avis préalable.
ISO 9000, à d'autres procédures d'assurance qualité, aux réglementations en matière d'hygiène alimentaire et d'environnement ainsi qu'aux HACCP. Les certifi cats Comark sont délivrés à l'issue de contrôles de la qualité indépendants qui comparent la performance d'un produit envers celle d'une norme nationale convenue. Pour avoir l'esprit tranquille et être dans les règles, Comark conseille de demander une...
Seite 33
Homologation identifi able par rapport au NPL Les certifi cats NPL de Comark offrent une incertitude de 0,3°C et la traçabilité est assurée par le Laboratoire National de Physique anglais (NPL). Conformité Les certifi cats de conformité peuvent être fournis pour les instruments neufs et ceux ayant subi une révision et un réétalonnage.
INTRODUCTION La Série C9500 IS comprend: C9501/IS Plage 0 de ±2 PSI / 0 de ±140mbar Différentiel C9503/IS Plage 0 de ±5 PSI / 0 de ±350mbar Différentiel C9505/IS Plage 0 de ±30 PSI / 0 de ±2000mbar Différentiel C9507/IS Plage 0 de ±100 PSI / 0 de ±6900mbar Différentiel For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
TOUCHES DE FONCTION Touche ON/OFF Appuyez une fois sur le bouton ON/OFF pour mettre l’appareil en marche. Appuyez de nouveau pour l’arrêter. Le maintien de la touche lors de la mise en marche permet d’affi cher la plage de pression maximale de l’appareil en PSI.
Touche FILTER Appuyez sur cette touche pour fi ltrer les lectures instables. En mode fi lter, l’appareil fera la moyenne des lectures prises au cours des 4 dernières secondes (16 relevés) pour assurer une meilleure stabilité de la lecture à l’affi chage. Appuyez de nouveau sur cette touche pour reprendre normalement les mesures.
Remarque: Les appareils de mesure de la pression de la Série C9500 IS de Comark ne conviennent pas pour la mesure de la pression absolue. Remarque: Il ne faut pas mettre ni l’un ni l’autre des orifi...
AUTRES FONCTIONS Pile Faible L’état de pile faible est indiqué par le symbole BAT à l’affi chage. Remplacez la pile dès que possible, à l’apparition de ce symbole. Dépassement de Pression Si la pression mesurée (pression positive ou négative) dépasse la valeur d’échelle maximale de l’appareil, l’affi...
Remplacement de la Pile Dévisser au dos de l’appareil les deux vis à tête hexagonale du compartiment à pile et enlever le couvercle en le faisant glisser. Remplacer la pile usagée par une pile de type 9V PP3 comme il est indiqué...
SPECIFICATION C9501/IS C9503/IS C9505/IS C9507/IS Plage 0 à ±2 0 à ±5 0 à ±30 0 à ±100 Résolution 0,001 0,001 0,01 mBar Plage 0 à ±140 0 à ±350 0 à ±2000 0 à ±6900 Résolution Plage 0 à ±55 0 à...
Seite 41
NIVEAUX DE II 1 G EEx ia IIC T4 Baseefa 03 ATEX 0079 ALIMENTATION Pile de type PP3 6F22 de 9V — MN1604 UCAR9V DUREE DE VIE 125 heures (en utilisant MN1604) DE LA PILE CONTROLE DE Affi che BAT juste avant que la pile PILE FAIBLE soit à...
MANOMETRI A SICUREZZA INTRINSECA DELLA SERIE C9500 INFORMAZIONI GENERALI Questi strumenti sono stati certifi cati dal Baseefa 2001 Limited e sono adatti agli impieghi inidcati dai marchi apposti. I contrassegni sono descritti nella clausola 28 di EN 50014. AVVERTENZA La certifi cazione di questo strumento è: II 1 G EEx ia IIC T4 Baseefa 03 ATEX 0079 LE NORME EN 50 020 DELLA SICUREZZA...
Seite 43
Dichiarazione di Conformità. In applicazione della sua politica di sviluppo continuo dei prodotti, la Comark Instruments si riserva il diritto di modifi care la specifi ca del prodotto senza preavviso. Per maggiori informazioni, rivolgersi alla Comark Instruments o al distributore di zona.
No. 0451 Certifi cazione La Comark può fornire, per tutta la sua gamma di prodotti, i certifi cati di taratura conformi alle procedure di controllo della qualità ISO 9000 e altri, per le norme d'igiene alimentare, per sistemi HACCP e per le norme ambientali.
Seite 45
Conformità La Comark rilascia certifi cati di conformità per strumenti nuovi, riparati e ritarati. Questi certifi cati confermano che gli strumenti sono conformi alle specifi che originali del fabbricante Manutenzione/Riparazione Il reparto manutenzione della Comark offre un servizio di manutenzione ed effettua tutte le riparazioni necessarie, anche tramite il proprio distributore locale.Per maggiori informazioni sui servizi di certifi...
INTRODUZIONE La serie di misuratori di pressione C9500 IS comprende: C9501/IS Campo 0 a ±2 PSI / 0 a ±140mbar Differenziale C9503/IS Campo 0 a ±5 PSI / 0 a ±350mbar Differenziale C9505/IS Campo 0 a ±30 PSI / 0 a ±2000mbar Differenziale C9507/IS Campo 0 a ±100 PSI / 0 a ±6900mbar Differenziale For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
FUNZIONI DEI TASTI Tasto ON/OFF Premere una volta per accendere lo strumento. Ripremere per spegnerlo. Per visualizzare il massimo campo di pressione dello strumento in PSI, mantenere premuto il tasto al momento dell’accensione. Mantenendo premuto il tasto di spegnimento, verrà effettuato un test, mostrando tutti i segmenti del visualizzatore.
Tasto FILTER Premere per eliminare le letture transitorie. Nella modalità FILTER, lo strumento calcola la media delle letture effettuate negli ultimi 4 secondi (16 letture) per fornire una lettura più stabile. Per riprendere la misurazione normale basta ripremere il tasto. Tasto RECORD Premere una volta il tasto per selezionare la modalità...
Nota: La serie di misuratori di pressione Comark C9500 IS non è indicata per la misurazione della pressione assoluta. Nota: Non devono essere applicate allo strumento pressioni che superino il massimo consentito in rispetto alla pressione atmosferica, poichè...
ALTRE FUNZIONI Esaurimento Batteria L’esaurimento della batteria è indicato dalla scritta BAT che appare sul visualizzatore. Quando appare questa scritta conviene sostituire non appena possibile la batteria. Pressione fuori Campo Se la pressione misurata (positiva o negativa) supera la massima pressione misurabile con lo strumento, appaiono sul visualizzatore dei trattini come questi –...
Sostituzione Batteria Svitare le due viti Allen alla base dello strumento e far scorrere la copertura della batteria. Sostituisci la batteria con un tipo 9V PP3 come specifi cato sull’etichetta nel compartimento della batteria. Riinserire la copertura della batteria facendo attenzione di non stringere troppo le due viti.
DATI TECNICI C9501/IS C9503/IS C9505/IS C9507/IS Campo 0 a ±2 0 a ±5 0 a ±30 0 a ±100 Risoluzione 0,001 0,001 0,01 mBar Campo 0 a ±140 0 a ±350 0 a ±2000 0 a ±6900 Risoluzione Campo 0 a ±55 0 a ±140 0 a ±830 0 a ±2750 Risoluzione...
Seite 53
DURATA DELLA 125 ore (usando MN1604) BATTERIA SEGNALE DI Appare la scritta BAT poco prima ESAURIMENTO dell’esaurimento totale della batteria BATTERIA SEGNALE DI – – – – PRESSIONE FUORI CAMPO FUORI CAMPO Lampeggiamento dei 4 digit CONNESSIONI Connettori femmina BSP da "...
MANOMETROS INTRINSECAMENTE SEGURAS DE LA SERIE C9500 INFORMACION GENERAL Estos instrumentos han sido certifi cados por el Baseefa 2001 Limited, y son aptos para uso de acuerdo con las marcas indicadas en ellos. Se describen las marcas en Cláusula 28 de EN 50014. ADVERTENCIA Le Certifi...
Seite 55
Disponemos de las declaraciones de conformi- dad. Consultar con el Distribuidor de Comark. De acuerdo con su política de desarrollo continuo, Comark Instruments se reserva el derecho de modifi car la especifi cación del instrumento sin aviso previo. Se puede obtener información adicional de Comark Instru- ments o de su distribuidor.
CALIBRACION, CERTIFICACION Y SERVICIO No. 0451 Certifi cación Comark puede facilitar certifi cados de calibración para toda su gama de productos, para adaptarse a la ISO 9000 y a otros procedimientos de aseguramiento de la calidad, reglamentos de higiene alimentaria, HACCPs y reglamentos medioambientales.
Seite 57
Servicio / Reparaciones Bajo el periodo de garantía o con posterioridad, el Departamento de Servicio Comark llevará a cabo el servicio regular y cualquier reparación necesaria.Para más información acerca de cualquier certifi cación, calibración y servicios por parte de Comark, sírvanse contactar con nuestro Servicio al Cliente o contacten con su distribuidor local.
INTRODUCCION La serie C9500 IS incluye: C9501/IS Escala 0 a ±2 psi/0 a ±140 milibares Diferencial C9503/IS Escala 0 a ±5 psi/0 a ±350 milibares Diferencial C9505/IS Escala 0 a ±30 psi/0 a ±2000 milibares Diferencial C9507/IS Escala 0 a ±100 psi/0 a ±6900 milibares Diferencial For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
FUNCIONES DE LAS TECLAS Tecla ON/OFF Pulsar la tecla una vez para encender el instrumento. Repita la operación para apagarlo. Manteniendo pulsada la tecla cuando enciende el instrumento visualiza el rango máximo de presión del instrumento en psi (libras por pulgada cuadrada). Manteniendo pulsada la tecla cuando apaga el instrumento visualiza todos los segmentos como una prueba.
Tecla FILTER (FILTRAR) Se pulsa para fi ltrar lecturas transitorias. En la modalidad FILTER, el instrumento toma el promedio de las lecturas tomadas durante los 4 últimos segundos (16 lecturas) para visualizar una lectura más estable. Se pulsa nuevamente la tecla para retornar a la medición normal.
Verifi car que los líquidos o gases cuya presión se mide no dañen ni corroan el acero inoxidable, latón, cristal, cerámica, silicio, niquel, aluminio, oro o resina epoxy. Nota: Los manómetros Comark de la Serie C9500 IS no son adecuados para la medición de presiones absolutas.
OTRAS FUNCIONES Batería Descargada El símbolo BAT aparece en la visualización cuando la pila está muy descargada. Sustituir la pila lo antes posible después de que aparece el símbolo. Presión Fuera de Escala La visualización presentará - - - - si la presión que se mide (sea positiva o negativa) excede la escala total del instrumento.
Reemplazar Batería Afl ojar los dos tornillos Allen en la base del instrumento y sacar la tapa del compartimento de la batería. Utilizar una pila del tipo 9V PP3 como se indica en la etiqueta. Volver a colocar la tapa sin apretar excesivamente los tornillos.
ESPECIFICACION C9501/IS C9503/IS C9505/IS C9507/IS Rango 0 a ±2 0 a ±5 0 a ±30 0 a ±100 Resolucion 0,001 0,001 0,01 mBar Rango 0 a ±140 0 a ±350 0 a ±2000 0 a ±6900 Resolucion Rango 0 a ±55 0 a ±140 0 a ±830 0 a ±2750 Resolucion...
Seite 65
VERIFICACION Visualiza BAT justo antes del DE PILA agotamiento de la pila DESCARGADA INDICACION DE – – – – FUERA DE ESCALA INDICACION DE Los 4 dígitos más bajos parpadean LECTURA DE MAS DE 9999 CONEXIONES Conector hembra de pulgada BSP PESO 330gm, la pila incluida Probado a EN 61326-1...
Seite 67
For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
Seite 68
For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...
Seite 69
For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk For latest prices and delivery to your door visit MyTub Ltd - www.mytub.co.uk - info@mytub.co.uk...