Inhaltsverzeichnis
Werbung
Quicklinks
Werbung
Inhaltsverzeichnis
Inhaltszusammenfassung für Advantech IPC-6806
- Seite 1 IPC-6806 6-slot Node IPC Chassis...
- Seite 2 Copyright Notice This document is copyrighted, January 1997, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
-
Seite 3: Inhaltsverzeichnis
Contents Chapter 1 General Information ........1 Introduction ................1 Specifications ..............1 Dimensions ................. 3 Installation ................4 Chapter 2 System Setup ..........5 Removing the cover ............5 Adding disk drives ............... 6 Hold-down clamp ..............7 Wall mounting ..............8 Replacing the filter ............... -
Seite 4: Chapter 1 General Information
Introduction Specially designed for the factory floor and other harsh industrial environments, the IPC-6806 wallmount IPC chassis is ideal for system integrators or users who require a compact, rugged PC/AT-compatible system. The IPC-6806 features a 6-slot passive backplane and a 150-watt power supply. - Seite 5 5 ~ 17 Hz, 0.1" double-amplitude displacement 17 ~ 500 Hz, 1.5 G acceleration peak to peak • Shock (operating): 10 G acceleration peak (11 msec. duration) • Safety: Meets UL/CSA/TÜV • EMI: Meets FCC/VDE Class A • CE compliant IPC-6806 User's Manual...
-
Seite 6: Dimensions
Dimensions Unit: mm Chapter 1 General Information... -
Seite 7: Installation
Installation Unit: mm IPC-6806 User's Manual... -
Seite 8: Chapter 2 System Setup
Chapter 2 System Setup The following procedures are provided to assist you in installing drives, plug-in cards and the hold-down clamp into the IPC-6806. Removing the cover To remove the cover, proceed as follows: 1. Remove the two screws (one on each side) which secure the cover to the card cage (see Fig. -
Seite 9: Adding Disk Drives
Insert the FDD into the mounting bracket with its base facing inward. d. Connect a 34-pin flat cable and power cable to the FDD, and attach the FDD to the bracket with four screws. Figure 2-2: Installing the drives IPC-6806 User's Manual... -
Seite 10: Hold-Down Clamp
Hold-down clamp 1. Insert the rubber buffers (provided in your kit) into the hold-down clamp (see Fig. 2-3). These buffers cushion the plug-in cards from shock and vibration. They have two settings: a. For XT-size cards, the narrow end should face upward. b. -
Seite 11: Wall Mounting
Wall mounting The IPC-6806 may be mounted on a wall, allowing more efficient use of space. To wall-mount your chassis, proceed as follows: 1. Attach the brackets to the chassis by inserting the six screws (provided in your kit) as shown in Fig. 2-4. -
Seite 12: Replacing The Filter
Replacing the filter To change the filter, located at the front end of the chassis, see Fig. 2-5 and proceed as follows: 1. Remove the two screws located at the bottom of the filter cover. Gently but firmly pull the cover free from the chassis. 2. - Seite 13 IPC-6806 User's Manual...
-
Seite 14: Appendix A Passive Backplanes
PCA-6106: 6-slot ISA-bus backplane Bus termination: Resistor ..Signals Resistor ..Signals RP5 ....SA7-SA0 RP2 ....SMEMW, SMEMR, IOW, IOR RP4 ....SA15-SA8 RP6 ....SBHE, LA23-LA17 RP1 ....SD7-SD0 RP3 ....LA19-LA16 RP7 ....SD8-SD15 IPC-6806 User's Manual... - Seite 15 PCA-6106P3: 2 ISA / 3 PCI / 1PICMG-slot backplane Bus termination: Resistor ..Signals Resistor ..Signals RN4 ....SA7-SA0 RP1 ....SMEMW, SMEMR, IOW, IOR RN3 ....SA15-SA8 RN5 ....SBHE, LA23-LA17 RN2 ....SD7-SD0 RN1 ....LA19-LA16 RN6 ....SD8-SD15 IPC-6806 User's Manual...
-
Seite 16: Appendix B Exploded Diagram
Appendix B Exploded Diagram IPC-6806 User's Manual... - Seite 17 IPC-6806 User's Manual...
-
Seite 18: Appendix C Safety Instructions
The sound pressure level at the operator's position according to IEC 704-1:1982 is equal to or less than 70 dB(A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. IPC-6806 User's Manual... -
Seite 19: Wichtige Sicherheishinweise
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70 dB(A) oder weiger. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. IPC-6806 User's Manual...