Seite 1
DMM 12BC BEDIENUNGSANLEITUNG ....... 2 Bitte vor Inbetriebnahme des Gerätes lesen! USER INSTRUCTIONS ......40 Please read the manual before using the equipment!
Consult the dealer or an experienced radio/TV technician for help. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved in writing by AKG Acoustics may void the user’s authority to operate this equipment.
Verwenden Sie das Gerät nur für die in dieser Bedienungsanleitung beschriebenen Anwendungen. Für Schäden infolge unsachgemäßer Handhabung oder missbräuchlicher Verwendung kann AKG keine Haftung übernehmen. Umwelt x Am Ende der Lebensdauer des Produkts trennen Sie Gehäuse, Elektronik und Kabel voneinander und entsorgen Sie alle Komponenten gemäß...
2 Beschreibung Einleitung Vielen Dank, dass Sie sich für ein Produkt von AKG entschieden haben. Bitte lesen Sie die Bedienungsanleitung aufmerksam durch, bevor Sie das Gerät benützen, und bewahren Sie die Bedienungsanleitung sorgfältig auf, damit Sie jederzeit nachschlagen können. Wir wünschen Ihnen viel Spaß...
Mit dem Drehregler "SYSTEM CONTROL" können die anliegenden Audiopegel der Eingänge angezeigt werden, siehe DMM 12BC bedienen. Eingänge Der DMM 12BC verfügt über 12 symmetrische Eingangskanäle zum Anschließen von niederohmigen dynamischen oder Kondensatormikrofonen und anderen Signalquellen, z.B. Empfänger für drahtlose Mikrofone. Für jeden Eingangskanal ist ein Drehregler vorhanden.
Ausgang kann nur einzeln, aber in Stereo abgehört werden. Beim Drücken auf eine andere Abhörquelle (Wechsel zwischen Eingängen und Ausgang), wird die vorherige abgeschaltet. Der Ausgang "REC (OUT)" kann nicht abgehört werden. Rückseite Abbildung 2: Rückseite des DMM 12BC Eingangskanäle 1-12 Gain-Regler 1-12 Phantomspeisung für je 2 Eingangskanäle...
Um ein Stereo-Aufnahmegerät anzuschließen sind zwei, mit "REC (OUT)" bezeichnete, Cinch- Buchsen vorhanden. Die Zuordnung einzelner Kanäle zum unsymmetrischen Stereo-Record- Ausgang ist frei konfigurierbar. Expansions-/Kaskadierungs-Anschlüsse Abbildung 8: EXPANSION Um eine Expansion-/Kaskadierung vorzunehmen sind zwei RJ-45-Buchsen vorhanden. Diese sind mit der Aufschrift "IN - EXPANSION - OUT" bezeichnet. DMM 12BC...
Mit einer Phönix-Klemme lässt sich das Gehäuse mit dem 0 V-Potential der Spannungsversorgung verbinden. Das 0 V-Potential nur mit der Erdung brücken (Werkseinstellung) oder zu der zentralen Systemerde führen, da die Phantomspeisung sonst keinen Bezugspunkt besitzt und diese nicht funktioniert. HINWEIS DMM 12BC...
Seite 9
Digitaler Ausgang Abbildung 13: Digitaler Ausgang Der DMM 12BC verfügt über einen digitalen Ausgang, welcher auf der Rückseite des Gerätes, über einen symmetrischen AES/EBU- oder einen optischen S/PDIF-Ausgang abgegriffen werden kann. Der AES/EBU-Ausgang ist über eine 3-polige Phoenix-Klemme zugänglich. Die Belegung von links nach rechts ist a, b, Schirm.
Dauerhaft vorhandene Störsignale, dessen Amplitude groß genug sind um als dominant bewertet zu werden, jedoch eine zu geringe Pegel- und Frequenzänderungen haben, werden als nicht dominant bewertet. Störsignale wie Lüfter- und Klimaanlagengeräusche werden erkannt und nicht als Aufschaltkriterium für die Mikrofonkanäle herangezogen. DMM 12BC...
Rackmontage Montieren Sie den DMM 12BC in Ihrem 19"-Rack. Kaskadieren Zur Kaskadierung empfehlen wir ausschließlich Kabel aus dem AKG-Zubehör zu verwenden. HINWEIS Das Gerät verfügt über zwei 100 MBit/s-Ethernet-Schnittstellen. Diese dienen zur Steuerdaten- und Audio-Kommunikation zwischen bis zu 10 Geräten. Somit lässt sich ein Automisch-System mit bis zu 120 Eingangskanälen, 40 Ausgangskanälen und 10 Stereo-...
Lesen Sie für das Anschließen auch die Bedienungsanleitung Ihrer Mikrofone und Zusatzgeräte durch. HINWEIS Schließen Sie die Mikrofone und Zusatzgeräte an der Rückseite des DMM 12BC an: Schließen Sie die Mikrofone und andere Signalquellen (z.B. Empfänger für drahtlose Mikrofone) an die "IN" - Eingangskanäle an.
Schalten Sie das Gerät mit dem Netzschalter ein. DMM 12BC bedienen So bedienen Sie die Drehregler an der Frontplatte des DMM 12BC: Abbildung 15: Bedienung des Drehreglers Drehen Sie die Drehregler im oder gegen den Uhrzeigersinn um Änderungen an Ein- und Ausgängen sowie Funktionseinstellungen vorzunehmen.
Beeinflussen Sie den Stereo-Ausgangskanal für Kopfhörer mit dem Drehregler "HEADPHONE". Stereo-Record-Ausgang digitale Ausgang verfügen über keine Einstellmöglichkeiten. 5 Minuten nach der letzten Änderung springt der Drehregler "SYSTEM CONTROL" wieder in die Funktion "LEVEL". 1 Minute nach der letzten Änderung wird der eingestellte Wert automatisch gespeichert. HINWEIS DMM 12BC...
Eine Ausnahme bildet hier der Drehregler "HEADPHONE". Der Stereo-Kopfhörer-Ausgang befindet sich immer im Modus "LEVEL", unabhängig von der Stellung des "SYSTEM CONTROL" Drehreglers. DSP Funktionen Folgende Funktionen zur Signalverarbeitung stehen für die Eingangskanäle und die Ausgangskanäle am Drehregler "SYSTEM CONTROL" zur Verfügung: DMM 12BC...
Seite 16
Abbildung 19: Teilung des LED - Kranzes der LEVEL Funktion Von -12 dB bis +15 dB ist die einstellbare Schrittweite 1 dB pro Raster. 3 dB entsprechen einer LED. Von - dB bis -12 ist die einstellbare Schrittweite 3 dB. 9 dB entsprechen einer LED. DMM 12BC...
Seite 17
übrigen LED-Felder. Das LED-Feld leuchtet auf, sobald der 0dB-Pegel erreicht wird (nach dem dritten Rasten, siehe Detail „Level“). VU Funktion: Mit dem Drehregler "SYSTEM CONTROL" können die anliegenden Audiopegel der Eingänge angezeigt werden, siehe DMM 12BC bedienen. HINWEIS TREBLE Abbildung 21: TREBLE Funktion Im Modus "TREBLE"...
Seite 18
Die einstellbare Schrittweite beträgt 2 dB pro Raster, dies entspricht einer LED. Abbildung 24: Regelmöglichkeit der TREBLE Funktion BASS Abbildung 25: BASS Funktion Im Modus "BASS" können alle Eingangs- und Ausgangskanäle beeinflusst werden. Abbildung 26: Regelmöglichkeit der Funktion DMM 12BC...
Seite 19
Seite auf. Je weiter der Drehregler nach rechts gedreht wird, desto mehr LEDs leuchten auf der rechten Seite auf. Abbildung 27: Teilung des LED - Kranzes der BASS Funktion Die einstellbare Schrittweite beträgt 2 dB pro Raster, dies entspricht einer LED. Abbildung 28: Regelmöglichkeit der BASS Funktion DMM 12BC...
Seite 20
Uhrzeigersinn absenken. Die Einstellmöglichkeit reicht von 0 Hz (keine Wirkung) bis 150 Hz (starke Abschwächung). Bei 0 Hz leuchtet eine LED, bei 150 Hz leuchtet der komplette LED-Kranz. Abbildung 31: Teilung des LED - Kranzes der LOW CUT Funktion DMM 12BC...
Seite 21
Die Einstellmöglichkeit reicht von +20 dBu bis -25 dBu. Bei +20 dBu leuchtet eine LED, bei - 25 dBu leuchtet der komplette LED-Kranz. Abbildung 34: Teilung des LED - Kranzes der LIMITER Funktion Die einstellbare Schrittweite beträgt 3 dB pro Raster, dies entspricht einer LED. DMM 12BC...
Seite 22
1:2. Eine Drehung des Drehreglers im Uhrzeigersinn hebt die Wirkung an, eine Drehung gegen den Uhrzeigersinn schwächt die Wirkung ab. Die Einstellmöglichkeit reicht von +20 dBu bis -25 dBu. Bei +20 dBu leuchtet eine LED, bei - 25 dBu leuchtet der komplette LED-Kranz. DMM 12BC...
Seite 23
Bedienung Abbildung 38: Teilung des LED - Kranzes der COMPRESSOR Funktion Die einstellbare Schrittweite beträgt 3 dB pro Raster, dies entspricht einer LED. Abbildung 39: Regelmöglichkeit der COMPRESSOR Funktion DMM 12BC...
Seite 24
Mit einer Drehung eines Drehreglers im Uhrzeigersinn wird die Automatik-Mischfunktionen für den jeweiligen Kanal eingeschaltet. (LED-Kranz leuchtet komplett) Eine Drehung gegen den Uhrzeigersinn schaltet die Automatik-Mischfunktionen aus. (nur eine LED leuchtet) Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS DMM 12BC...
Seite 25
Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS Ein Einschalten der "PRIORITY" Funktion an einem Eingangskanal bewirkt ein Ausschalten der Funktion an dem vorher aktivierten Kanal. Diese Funktion kann nur an einem einzigen Eingangskanal aktiv sein. HINWEIS DMM 12BC...
Seite 26
Soll der linke Ausgangskanal eines Stereo-Ausgangs nicht mehr ausgeben werden, so ist der Balance-Regler nach rechts zu stellen. Bei Mono-Eingängen wird das Signal standardmäßig gleich auf Stereo-Links und -Rechts zugeteilt. Soll der Eingang nur links zugeteilt werden, so ist der Drehregler des Eingangs, bei aktiver PAN-Funktion, auf links zu stellen. DMM 12BC...
Seite 27
Die Einstellmöglichkeit reicht von 0 m bis 75 m. Bei 0 m leuchtet eine LED, bei 75 m leuchtet der komplette LED-Kranz. Abbildung 48: Teilung des LED - Kranzes der DELAY Funktion Die einstellbare Schrittweite beträgt 1 m pro Raster. 5 m entsprechen einer LED. DMM 12BC...
Seite 28
Kanal eingeschaltet (LED-Kranz leuchtet komplett). Eine Drehung gegen den Uhrzeigersinn schaltet die Funktion aus (nur eine LED leuchtet). Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS Ein Einschalten legt diesen Eingangskanal auf die Summenschiene OUT 1. DMM 12BC...
Seite 29
Kanal eingeschaltet (LED-Kranz leuchtet komplett). Eine Drehung gegen den Uhrzeigersinn schaltet die Funktion aus (nur eine LED leuchtet). Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS Ein Einschalten legt diesen Eingangskanal auf die Summenschiene OUT 2. DMM 12BC...
Seite 30
Kanal eingeschaltet (LED-Kranz leuchtet komplett). Eine Drehung gegen den Uhrzeigersinn schaltet die Funktion aus (nur eine LED leuchtet). Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS Ein Einschalten legt diesen Eingangskanal auf die Summenschiene REC. DMM 12BC...
Seite 31
Kanal eingeschaltet (LED-Kranz leuchtet komplett). Eine Drehung gegen den Uhrzeigersinn schaltet die Funktion aus (nur eine LED leuchtet). Durch Drücken auf den Drehregler wird die Funktion ebenfalls ein- bzw. ausgeschaltet. HINWEIS Ein Einschalten legt diesen Eingangskanal auf die Summenschiene DIGOUT. DMM 12BC...
Seite 32
Seite auf. Je weiter der Drehregler nach rechts gedreht wird, desto mehr LEDs leuchten auf der rechten Seite auf. Abbildung 59: Teilung des LED - Kranzes der Equalizer Funktion Die einstellbare Schrittweite beträgt 2 dB pro Raster, dies entspricht einer LED. DMM 12BC...
Seite 33
Durch kurzes Drücken eines Ein- oder Ausgangsdrehreglers, mit Ausnahme des Drehreglers "HEADPHONE", wird der entsprechende Kanal stumm geschaltet. Die MUTE Funktion wird durch gleichmäßiges Blinken des LED-Kranzes angezeigt. Ein weiteres kurzes Drücken oder Drehen des Drehreglers hebt die MUTE Funktion wieder auf. DMM 12BC...
Seite 34
Lautstärke verändert werden. Durch Drücken auf den Drehregler des gewünschten Kanals (länger als 3 Sekunden!) wird dieser von der Sperrung ausgenommen. Durch wiederholtes Drücken (länger als 3 Sekunden!) wird er wieder gesperrt. Die eingestellten LOCK Zustände bleiben auch nach Ausschalten / Wiedereinschalten des DMM 12BC erhalten! HINWEIS DMM 12BC...
Der Kopiervorgang ist in beide Richtungen möglich. ("IN 1" bis "IN 12" und "IN 12" bis "IN 1") HINWEIS Abbildung 63: Drehregler auswählen (Quelle) Abbildung 64: Kopierbereich definieren (Ziel) Abbildung 65: Drehregler gedrückt halten Abbildung 66: Kopiervorgang abgeschlossen DMM 12BC...
Seite 36
Warten Sie bis die Startsequenz des Automischers abgeschlossen ist (ca. 15 Sekunden). Lassen Sie den Drehregler "SYSTEM CONTROL" los. Das Gerät ist nun auf die Werkseinstellungen zurückgesetzt worden und kann für eine neue Systemkonstellation eingestellt werden. Durch das Rücksetzen auf Werkseinstellungen gehen alle gespeicherten Einstellungen verloren! HINWEIS DMM 12BC...
Reinigen Sie die Oberflächen des Gerätes mit einem mit Wasser befeuchteten, aber nicht nassen, Tuch. Verwenden Sie keinesfalls scharfe oder scheuernde Reinigungsmittel sowie keine, die Alkohol oder Lösungsmittel enthalten, da diese den Lack sowie die Kunststoffteile beschädigen könnten. ACHTUNG DMM 12BC...
Digital Analog Wandlung für Recording, Monitoring und Summen Ausgang Datenformat: 24 Bit Sample Frequenz: 48 kHz Dieses Produkt entspricht den in der Konformitätserklärung angegebenen Normen. Sie können die Konformitätserklärung auf http://www.akg.com nachlesen oder per E-Mail von sales@akg.com anfordern. DMM 12BC...
Vorverstärkung stellen Verzerrte Signalwiedergabe Lautstärkeregler sind zu weit Lautstärke zurückregeln aufgedreht Eingangssignal hat zu hohen Eingangssignal dämpfen Pegel Falls der Fehler trotz dieser Anweisungen weiter besteht, melden Sie sich umgehend bei AKG Acoustics GmbH, oder Ihrem AKG-Händler. DMM 12BC...
Seite 40
Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved in writing by AKG Acoustics may void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Use the unit only for the purposes described in these operating instructions. AKG will accept no liability for damage caused by incorrect handling or improper use.
In addition to many digital signal processing functions, the DMM 12BC also has innovative automatic mixing functions. Up to ten DMM 12BC can be cascaded if the twelve balanced inputs are not sufficient for your application. DMM 12BC...
These are labelled "IN 1" to "IN 12". Operating mode / system control The DMM 12BC has a large number of functions, such as volume, treble ranges, bass, auto- mix functions, etc. The "SYSTEM CONTROL" rotary knob can be used to select these functions.
Description Rear panel Figure 2: Rear panel of the DMM 12BC Input channels 1-12 Gain control 1-12 Phantom power for two input channels 4a, 4b: Output channel 1, stereo left, right 5a, 5b: Output channel 2, stereo left, right Stereo record output...
The allocation of the individual channels to the asymmetrical stereo recording output can be configured as desired. Expansion/cascading connections Figure 8: EXPANSION Two RJ-45 sockets are provided for expansion/cascading. These are labelled with "IN - EXPANSION - OUT". DMM 12BC...
A phoenix terminal connects the case with the 0 V potential of the power supply. Only bridge the 0 V potential with the grounding (factory setting) or connect it to the central system ground, as otherwise the phantom power has no reference point and will not function. NOTE DMM 12BC...
Digital output Figure 13: Digital output The DMM 12BC has a digital output which can be picked up via a balanced AES/EBU or an optical S/PDIF output on the rear panel of the device. The AES/EBU output can be accessed via a 3 pin Phoenix terminal.
Permanently present interfering signals, whose amplitude are large enough to be assessed as dominant, but whose level and frequency changes are too low, are not assessed as dominant. Interfering signals such as noise from fans and air-conditioning units are recognised and not used as activation criteria for microphone channels. DMM 12BC...
Installation and Connection 3 Installation and Connection Rack mounting Mount the DMM 12BC in your 19" rack. Cascading We recommend only using AKG accessory cables for cascading. NOTE The unit has two 100 MBit/s ethernet interfaces. These communicate the control data and audio between up to 10 units.
Connecting microphones and accessories Before connecting, read the operating instructions for your microphones and accessories. NOTE Connect microphones and accessories to the back of the DMM 12BC: Connect microphones and other signal sources (e.g. wireless microphone receivers) to the "IN" input channels.
A lower gain is recommended for microphones with a high output level. NOTE Turn the unit on at the power switch. The rotary knobs on the front panel of the DMM 12BC are operated as follows: DMM 12BC operation Figure 15: Operation of the rotary knob Turn the rotary knob clockwise or counter-clockwise to make changes to inputs and outputs and function settings.
Seite 52
Bass x Low Cut x Limiter x Compressor x Automixing x Priority x Pan / Balance x Delay x Routing to OUT 1 x Routing to OUT 2 x Routing to REC x Routing to DIGOUT x Equalizer DMM 12BC...
Seite 53
Equalizer x Monitoring x Mute Stereo headphone output modes (output for monitoring) The "HEADPHONE" rotary knob is an exception. The stereo headphone output is always located in the "LEVEL" mode, regardless of the "SYSTEM CONTROL" rotary knob setting. DMM 12BC...
The settings range from - to +15 dB (acoustic feedback). The adjustment takes place in the appropriate increments. An LED illuminates at -, while the entire LED ring is illuminated at +15 dB and the acoustic feedback is no longer provided. Figure 19: Division of the LED ring for the LEVEL function DMM 12BC...
Seite 55
The LED field illuminates as soon as the 0 dB level is reached (after the third click, see "Level" detail). VU function: The "SYSTEM CONTROL" rotary knob can be used to display the current audio level of the inputs, see DMM 12BC operation. NOTE DMM 12BC...
Seite 56
More LEDs light up on the right side as the rotary knob is turned further to the right. Figure 23: Increments on the LED ring for the TREBLE function The adjustable increments are equal to 2 dB per click and also correspond to one LED. DMM 12BC...
Seite 57
All the input and output channels can be controlled in the "BASS" mode. Figure 26: Adjustment range for the function The "BASS" function raises or lowers the audio signal's bass range. The filter is designed as a first order bass shelving filter. The cut-off frequency is 100 Hz. DMM 12BC...
Seite 58
More LEDs light up on the right side as the rotary knob is turned further to the right. Figure 27: Increments on the LED ring for the BASS function The adjustable increments are equal to 2 dB per click and also correspond to one LED. Figure 28: Adjustment range for the BASS function DMM 12BC...
Seite 59
The settings range from 0 Hz (no effect) to 150 Hz (severe attenuation). One LED is illuminated at 0 Hz, while the entire LED ring is illuminated at 150 Hz. Figure 31: Increments on the LED ring for the LOW CUT function DMM 12BC...
Seite 60
The settings range from +20 dBu to -25 dBu. One LED is illuminated at +20 dBu, while the entire LED ring is illuminated at -25 dBu. Figure 34: Increments on the LED ring for the LIMITER function The adjustable increments are equal to 3 dB per click and also correspond to one LED. DMM 12BC...
Seite 61
All the input channels can be controlled in the "COMPRESSOR" mode. Figure 37: Adjustment range for the function The compressor ratio is fixed. It has a value of 1:2. Turning the rotary knob in a clockwise direction increases the effect, while turning it counter-clockwise dampens the effect. DMM 12BC...
Seite 62
LED ring is illuminated at -25 dBu. Figure 38: Increments on the LED ring for the COMPRESSOR function The adjustable increments are equal to 3 dB per click and also correspond to one LED. Figure 39: Adjustment range for the COMPRESSOR function DMM 12BC...
Seite 63
(Entire LED ring is illuminated) Turning the rotary knob counter- clockwise switches the automatic mixing function off. (Only one LED is illuminated) Pressing the rotary knob also switches the function on or off. NOTE DMM 12BC...
Seite 64
Pressing the rotary knob also switches the function on or off. NOTE Switching on the "PRIORITY" function on an input channel turns off the function on the previously activated channel. This function can only be active on a single input channel. NOTE DMM 12BC...
Seite 65
In mono inputs, the signal is assigned equally to stereo left andright as standard. If the input is to be assigned to the left only , turn the rotary knob for the input to the left when the PAN function is active. DMM 12BC...
Seite 66
The settings range from 0 m to 75 m. One LED is illuminated at 0 m, while the entire LED ring is illuminated at 75 m. Figure 48: Increments on the LED ring for the DELAY function The adjustable increments are equal to 1 m per click. 5 m is equal to one LED. DMM 12BC...
Seite 67
(entire LED ring is illuminated). Turning the rotary knob counter-clockwise switches the function off (only one LED is illuminated). Pressing the rotary knob also switches the function on or off. NOTE Switching this on sets the input channel to the OUT 1 master bus. DMM 12BC...
Seite 68
(entire LED ring is illuminated). Turning the rotary knob counter-clockwise switches the function off (only one LED is illuminated). Pressing the rotary knob also switches the function on or off. NOTE Switching this on sets the input channel to the OUT 2 master bus. DMM 12BC...
Seite 69
(entire LED ring is illuminated). Turning the rotary knob counter-clockwise switches the function off (only one LED is illuminated). Pressing the rotary knob also switches the function on or off. NOTE Switching this on sets the input channel to the REC master bus. DMM 12BC...
Seite 70
(entire LED ring is illuminated). Turning the rotary knob counter-clockwise switches the function off (only one LED is illuminated). Pressing the rotary knob also switches the function on or off. NOTE Switching this on sets the input channel to the DIGOUT master bus. DMM 12BC...
Seite 71
More LEDs light up on the right side as the rotary knob is turned further to the right. Figure 59: Increments on the LED ring for the equalizer function The adjustable increments are equal to 2 dB per click or one LED. DMM 12BC...
Seite 72
The respective channel is switched to mute by briefly pushing the input or output rotary knob, with the exception of the "HEADPHONE" rotary knob. The MUTE function is indicated by the steady flashing of the LED ring. Another brief press or turn of the rotary knob removes the MUTE function. DMM 12BC...
Seite 73
Pressing the rotary knob again (for longer than 3 seconds!) relocks the channel. The set LOCK states are retained even after switching the DMM 12BC off and on again! NOTE Copy function for configuration data...
Seite 74
The copy process can be performed in both directions. ("IN 1" to "IN 12" and "IN 12" to "IN 1") NOTE Figure 63: Select the rotary knob (source) Figure 64: Define the copy range (target) Figure 65: Hold down the rotary knobs Figure 66: Copy process complete DMM 12BC...
Wait until the automixer has completed its start sequence (approx. 15 seconds). Release the "SYSTEM CONTROL" rotary knob. The unit's factory settings have now been restored and a new system configuration can now be set up. Resetting the factory settings deletes all of the stored settings! NOTE DMM 12BC...
Unplug the power supply cable from the socket. Clean the surface of the unit with a moistened (not wet) cloth. Never use caustic or scouring cleaners or cleaning agents containing alcohol or solvents, since these may damage the enamel and plastic parts. ATTENTION DMM 12BC...
Digital analogue conversion for recording, monitoring and master output Data format: 24 bit Sample frequency: 48 kHz This product conforms to the standards listed in the Declaration of Conformity. To view a copy of the Declaration of Conformity for this product, visit http://www.akg.com or contact sales@akg.com. DMM 12BC...
Distorted signal Volume control turned up too Turn down volume reproduction Input signal level too high Reduce input signal If the error persists despite these instructions, contact AKG Acoustics GmbH or your AKG dealer immediately. DMM 12BC...
Seite 79
Lemböckgasse 21–25, A-1230 Vienna/AUSTRIA, phone: (+43-1) 86654-0 e-mail: sales@akg.com For other products and distributors worldwide visit www.akg.com Technische Änderungen vorbehalten. Specifications subject to change without notice. Ces caractéristiques sont susceptibles de modifications. Ci riserviamo il diritto di effettuare modifiche tecniche. Nos reservamos el derecho de introducir modificaciones técnicas. Especificações sujeitas a mudanças sem aviso prévio.