Inhaltszusammenfassung für Helios ultraSilence ELS-GUBA
Seite 1
Helios Ventilatoren MONTAGE- UND BETRIEBSVORSCHRIFT INSTALLATION AND OPERATING INSTRUCTIONS Kunststoffgehäuse ¬ mit Brandschutzabsperrvorrichtung Plastic casing with fire damper ELS-GUBA (Unterputz) (flush-mounted)
Seite 2
Korrekte Entsorgung dieses Produktes (Elektromüll) Die Kennzeichnung auf dem Produkt bzw. auf der dazugehörigen Montage- und Betriebsvorschrift gibt an, dass es nach seiner Lebensdauer nicht zusammen mit dem normalen Haushaltsmüll entsorgt werden darf. Entsorgen Sie dieses Gerät bitte getrennt von anderen Abfällen, um der Umwelt bzw. der menschlichen Gesund- heit nicht durch unkontrollierte Müllbeseitigung zu schaden.
Wenn die nachfolgenden Ausführungen nicht beachtet werden, entfällt unsere Gewährleistung. Gleiches gilt für Haf- tungsansprüche an den Hersteller. Der Gebrauch von Zubehörteilen, die nicht von Helios empfohlen oder angeboten werden, ist nicht statthaft. Even tuell auftretende Schäden unterliegen nicht der Gewährleistung.
Länge der Ausblasleitung über 1,5 m und einer Geschosshöhe über 2,75 m erhöhte Druckverluste entstehen, die durch größeren Querschnitt der Hauptleitung ausgeglichen werden müssen. Zur Dimensionierung kann die Helios-ELS-Software eingesetzt werden. Erhältlich über die Helios Website: www .heli- osventilatoren .de.
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 3 .0 ELS-GUBA Kunststoffgehäuse mit Brandschutzabsperrvorrichtung KAPITEL 3 – geeignet zum Einbau in Gebäude mit Brandschutzanforderung K90 und qualifiziertem Brandschutzschacht. Einbau außerhalb des qualifizierten Schachtes in Kombination mit Stahl-/Stahlflexleitung DN 80 mm. ELS-LIEFERUMFANG UND EINBAU Lieferumfang / Verpackungseinheit, Abb.1 3 .1 ELS-GUBA Unterputzgehäuse...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .1 Einbaulage (nach links bzw. rechts 90° gedreht). Ausblasstutzen mit luftdicher Rückluft-Sperrklappe um 90° drehen . HINWEIS Für alle Einbaulagen mit Stutzen senkrecht nach oben, Rückholfeder entfernen! (siehe Punkt 4 .10) Zum Wechseln der Ein- ELS-GUBA ELS-GUBA Ausblasstutzen...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .2 Unterputzgehäuse ELS-GUBA mit Brandschutzklappe / wahlweise auch für Zweitraum BRANDSCHUTZ Die Unterputzgehäuse ELS-GUBA mit Brandschutzabsperrklappe und luftdichter Rückluft-Sperrklap- pe aus Metall sind für den Einbau in Wohneinheiten mit K90 oder K90K Anforderungen außerhalb des qualifizierten Schachts in Verbindung mit Stahl- oder Stahlflexleitung vorgesehen.
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .5 Montagehalter ELS-MHU für UP-Gehäuse montieren Erforderlich für Unterputzmontage von ELS-GUBA im Schacht, bei dünnen Vormauerungen, Beplankung oder Decke. Lieferumfang: â Wandbügel ê Seitenschiene ô Montagebügel û 2x Sechskantschraube M6 x16 á 2x Sechskantmutter M6 é...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .6 Montagebügel ELS-MB für Vorwandsysteme montieren Lieferumfang: â Montagebügel û Sechskantschraube 2x á Sechskantmutter 2x Wanddübel, Schrauben bauseits! HINWEIS Die Befestigung am Vorwandsystem erfolgt mit Vorwandsystemeigenen Winkeln bzw . Wandhaltern (Pos a .) . Abb .21 Abb .22 û...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .7 ELS-Einbaubeschreibung für beplankte Wand Abb .27 Abb .28 4 Andruck-Pins Andruck-Pin Abb .29 Abb .30 230x230 mm aussägen! 1. Position markieren Abb .31 Abb .32 6,6 mm 12,6 mm Montage des Ausgleichs- rahmen ELS-AGR zur Abdeckung von unsauberen oder zu großen Wandöffnungen.
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .8 Vorwandadapter und Ausgleichsrahmen ELS AR zu ELS-GUBA montieren Einbau: Vorwandadapter ELS-VA zum frontseitigen UP-Gehäuseeinschub in beplankte Sanitärwände. Lieferset bestehend aus Vorwandadapter und vier Kunststoffschrauben. Abb .33 Abb .34 Elektrische Leitung an den Anschlussklem- men im Gehäuse anschließen .
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .9 Montage Putzblende ELS-PB Die ELS-PB Putzblende dient zur Abdeckung von Spalten aufgrund unsauber eingeputzer/gefliester oder zu großer Gehäuseausschnitte, die von der Innenfassade nicht mehr abgedeckt werden. Die Blende wird zwischen Wand bzw. Decke und Innenfassade eingespannt. Abb .41 Abb .42 Maße in mm...
Seite 16
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .11 Wand- / Deckenmontage ELS-GUBA Gewünschte Position exakt ausrichten und Befestigungselemente fest verschrauben . Bei Leichtbaudecken HINWEIS eventuell zwischen Decke und Unterputzgehäuse schallisolierendes Material einlegen . Wandeinbau: Abb .45 Abb .46 6,6 mm 12,6 mm Ausblasstutzen ä...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 4 .12 Anschlussleitung (Stahl- bzw . Stahlflexleitung) Biegeradius R > DN der Anschlussleitung beachten! HINWEIS Stahl/Stahlflexleitung (DN 80) auf Ausblasstutzen stecken und mit Schraube (max. L = 20 mm, Position 64 mm) inkl. Flexband fest verbinden (Abb.49 u. 50). Abb .49 Abb .50 Biegeradius R >...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 5 .0 Schaltplan-Übersicht für ELS V . . Ventilator-Serien . Das zutreffende Verdrahtungsschema für die vorgesehenen Ventilatoren bitte ankreuzen! V 60 SS-869 V 100 SS-870 V 60/35 SS-871 V 100/35 SS-872 V 100/60 SS-873 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N...
Seite 19
When used in combination with a DSEL 3 controller a lamp must not be connected. Dauerphase bei Permanent life for Pour l'utilisation du DSEL3, Helios Type aucune lampe ne peut Alimentation permanente pour DSEL3 être raccordée. ELS VN, VNC, VF Typen SS-903 85052 001 SS-903 17.12.07...
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA 5 .2 Schaltplanübersicht für ELS EC . . Ventilator-Serien (zutreffendes Verdrahtungsschema für die vorgesehenen Ventilatoren bitte ankreuzen!) EC 100 N SS-1187 EC 100/35 N SS-1189 EC 60/45/25 NC SS-1197 EC 60/40/15 NC SS-1198 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N...
Seite 21
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA EC 60 NC SS-1165 EC 100 NC SS-1166 EC 60/35 NC SS-1167 EC 100/35 NC SS-1168 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N 100 m³/h 60 m³/h 100 m³/h...
Seite 22
Montage- und Betriebsvorschrift Gehäuse-Typen ELS-GUBA EC 60 P SS-1177 EC 100 P SS-1178 EC 60/45/25 F SS-1212 EC 100/60/35 F SS-1176 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N b) d) 100 m³/h 60 m³/h...
Seite 23
3 = große / high / grand à trois vitesses 1 2 3 L N ELS EC ... Helios Type DSEL3 85455 001 SS-1184 17.10.16 85456 001 SS-1185 17.10.16 ELS EC . . mit Drehzahl-/Betriebsschalter DSEL 2, zweitourige ohne ELS EC .
Seite 24
Correct disposal of this product (electrical waste) This marking shown on the product or its operating and installation Instructions indicates that it should not be disposed with other household waste at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources.
Installation and Operating Instructions Casing types ELS-GUBA 1 .0 Type overview of flush-mounted casing with fire damper CHAPTER 1 ELS-GUBA ¬ ELS QUICK OVERVIEW Flush-mounted casing fire damper, outside of shaft Ref . no . 8114 PAGE 6 1 .1 ELS accessories ELS-ARS ELS-AGR ELS-UPA...
If the preceding instructions are not observed all warranty claims and accommodation treatment are excluded. This also applies to any liability claims extended to the manufacturer. The use of accessories not offered or recommended by Helios is not permitted. Potential damages are not liable for warranty.
Throttle devices are not permitted. The diameter of the main line can be determined from the dimensioning diagram (Helios main catalogue). In this respect, it should be noted that there are increased pressure losses for a discharge line length over 1.5 m and a floor height over...
Installation and Operating Instructions Casing types ELS-GUBA 3 .0 ELS-GUBA plastic casing with fire damper CHAPTER 3 – suitable for installation in buildings with fire protection requirements K90 and appropriate fire protection shaft. Installation outside appropriate fire protection shaft in combination with steel/steelflex ducting DN 80 mm. ELS SCOPE OF DELIVERY AND ASSEMBLY Scope of delivery / Packaging unit, Fig.1...
Installation and Operating Instructions Casing types ELS-GUBA 4 .1 Fitting position (turned left or right by 90°). Turn discharge spigot with airtight backdraught shutter by 90 . NOTE For all fitting positions with spigot vertically to top, remove return spring! (see section 4 .10) To change the fitting ELS-GUBA ELS-GUBA...
Installation and Operating Instructions Casing types ELS-GUBA 4 .2 Flush-mounted casing ELS-GUBA with fire damper / also for second room FIRE PROTECTION The flush-mounted casing ELS-GUBA with fire damper and airtight metal backdraught shutter are designed for installa- tion in residential units with K90 or K90K requirements outside of appropriate shafts in connection with steel or steelflex ducting.
Installation and Operating Instructions Casing types ELS-GUBA 4 .3 Conversion Second room connection - Accessory ELS-ZS or ELS-ZAS required . NOTE Seal and make connection duct Aluflex/Steelflex DN 80 airtight. Fig .9 Fig .10 ELS-GUBA Discharge to top, Connec- tion for second room on left or right Break out opening for Attach ELS-ZAS 80 spigot in the flush-moun-...
Mounting bracket û 2x hexagon head screw M6 x16 á 2x hexagon nut M6 é 4x screws M6x10 (self-tapping) NOTE Wall-plugs, screws are not provided by Helios! Fig .15 Fig .16 ô á á û û Mounting bracket ô can be shortened at the indent.
Mounting holder û hexagon head screw 2x á hexagon nut 2x Wall-plugs, screws are not provided by Helios! NOTE Fixing to plasterboard systems takes place with plasterboard system specific brackets or wall holders (Pos a .) . Fig .21 Fig .22 û...
Installation and Operating Instructions Casing types ELS-GUBA 4 .7 ELS installation description for cladded wall Fig .27 Fig .28 4 press pins Press pin Fig .29 Fig .30 2. Saw out 230x230 mm! 1. Mark position Fig .31 Fig .32 6.6 mm 12.6 mm Installation of spacer frame...
Seite 36
(DN 80) to bend radius R > DN discharge spi- got and seal . Fig .35 Fig .36 Screws not provided by Helios Fig .37 Fig .38 Installation of spacer frame Installation of spacer frame ELS-AGR ELS-AGR for covering...
Installation and Operating Instructions Casing types ELS-GUBA 4 .9 Installation of plasterboard cover ELS-PB The ELS-PB plasterboard cover is used for covering gaps in case of casing cut-outs which have been uncleanly plastered, tiled or if they are too large, which cannot be completely covered by the inner facade. The plaster cover is fixed between the wall/ceiling and ELS inner facade.
Installation and Operating Instructions Casing types ELS-GUBA 4 .11 Wall / ceiling installation ELS-GUBA Precisely align desired position and firmly tighten fixing elements . In case of lightweight ceilings, insert NOTE sound-insulating material between ceiling and flush-mounted casing . Wall installation: Fig .45 Fig .46 6.6 mm...
Installation and Operating Instructions Casing types ELS-GUBA 4 .12 Connecting duct (Aluflex ducting) Observe bending radius R > DN of the connection cable! NOTE Connect steel/steelflex ducting (DN 80) to discharge openings and attach with screw (max. L = 20 mm, position 64 mm) incl.
Installation and Operating Instructions Casing types ELS-GUBA 5 .0 Wiring diagram overview for ELS V . . fan series (please mark applicable wiring diagram for the intended fans!) V 60 SS-869 V 100 SS-870 V 60/35 SS-871 V 100/35 SS-872 V 100/60 SS-873 1 2 3 L N...
Seite 41
When used in combination with a DSEL 3 controller a lamp must not be connected. Dauerphase bei Permanent life for Pour l'utilisation du DSEL3, Helios Type aucune lampe ne peut Alimentation permanente pour DSEL3 être raccordée. ELS VN, VNC, VF Typen SS-903 85052 001 SS-903 17.12.07...
Installation and Operating Instructions Casing types ELS-GUBA 5 .2 Wiring diagram overview for ELS EC . . fan series (please mark applicable wiring diagram for the intended fans!) EC 100 N SS-1187 EC 100/35 N SS-1189 EC 60/45/25 NC SS-1197 EC 60/40/15 NC SS-1198 1 2 3 L N...
Seite 43
Installation and Operating Instructions Casing types ELS-GUBA EC 60 NC SS-1165 EC 100 NC SS-1166 EC 60/35 NC SS-1167 EC 100/35 NC SS-1168 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N 100 m³/h 60 m³/h 100 m³/h...
Seite 44
Installation and Operating Instructions Casing types ELS-GUBA EC 60 P SS-1177 EC 100 P SS-1178 EC 60/45/25 F SS-1212 EC 100/60/35 F SS-1176 1 2 3 L N 1 2 3 L N 1 2 3 L N 1 2 3 L N b) d) 100 m³/h 60 m³/h...
Seite 45
3 = große / high / grand à trois vitesses 1 2 3 L N ELS EC ... Helios Type DSEL3 85455 001 SS-1184 17.10.16 85456 001 SS-1185 17.10.16 ELS EC . . with speed/operating switch DSEL 2, two-speed without ELS EC .
Seite 46
Installation and Operating Instructions Casing types ELS-GUBA...
Seite 47
Installation and Operating Instructions Casing types ELS-GUBA...
Seite 48
Service und Information HELIOS Ventilatoren GmbH & Co · Lupfenstraße 8 · 78056 VS-Schwenningen HELIOS Ventilateurs · Le Carré Aviateurs · 157 av. Charles Floquet · 93155 Le Blanc Mesnil Cedex CH HELIOS Ventilatoren AG · Tannstrasse 4 · 8112 Otelfingen GB HELIOS Ventilation Systems Ltd.