Audio Settings - Panasonic TY-TBN03G Bedienungsanleitung

Format
Select the SDI signal format.
SD: SD signal
1280: HD signal with effective horizontal pixels 1 280,
commonly known as 720p
1920: HD signal with effective horizontal pixels 1 920,
commonly known as 1080i or 1080p
2048: HD signal with effective horizontal pixels 2 048,
commonly known as 2K
3840: 4K signal with effective horizontal pixels 3 840,
commonly known as 4K
4096: 4K signal with effective horizontal pixels 4 096,
commonly known as 4K
4K division
Select the transmission method for 4K format.
SQUARE: Square Division method
INTERLEAVE: 2-Sample Interleave Division method
SDI mode
Select the SDI signal interface format.
1.5G HD-SDI: HD-SDI formats with 1.5 GHz
3G LEVEL A: HD-SDI format with 3 GHz LEVEL A
3G LEVEL B-DL: HD-SDI format with 3GHz LEVEL
B-DL (DUAL LINK)
3G LEVEL B-DS: HD-SDI format with 3 GHz LEVEL
B-DS (DUAL STREAM)
Colour space
Select the display method for colour space.
YCBCR: Y brightness signal, C
signal, C colour-difference signal
R
RGB: Primary colour R/G/B signals
XYZ: Colourimetric X/Y/Z signals
Sampling structure
Select the sampling rate of brightness signal and colour-
difference signal for SDI signal.
4:2:2: The sampling rate for Y signal, C
signals is 4:2:2.
4:4:4: The sampling rate for Y signal, C
signals is 4:4:4, or the sampling rate for R/G/B
signals or X/Y/Z signals is 4:4:4.
Bit depth
Select the quantization bit rate for SDI signal.
8BIT: 8 bit
10BIT: 10 bit
12BIT: 12 bit
colour-difference
B
and C
B R
and C
B R

Audio settings

By installing this terminal board in a compatible display,
audio settings for this terminal board can be made by
using the display.
For projector
Audio settings are not available since they are not
equipped with audio function.
For flat panel display
The description of audio settings below is based on
the flat panel display LQ series as an example.
The setting can be made on "Sound" for the main unit
menu.
Group select
Select the audio group from 16 channels for SDI signals.
Channel 1-8: Selects channel 1 to channel 8.
Channel 9-16: Selects channel 9 to channel 16.
Left channel
Select the channel of SDI audio to be output to the left
channel.
When "Channel 1-8" is selected for "Group select",
the channel can be selected from channels 1 to 8.
When "Channel 9-16" is selected for "Group select",
the channel can be selected from channels 9 to 16.
Right channel
Select the channel of SDI audio to be output to the right
channel.
When "Channel 1-8" is selected for "Group select",
the channel can be selected from channels 1 to 8.
When "Channel 9-16" is selected for "Group select",
the channel can be selected from channels 9 to 16.
Note
●
Audio output will be suspended if signals other than
those (page 15) supported by this terminal board are
input.
●
Audio output will be suspended if channels that are
not multiplexed to the SDI signal are selected.
●
The following error messages will be displayed if any
problem occurs with SDI signals.
Unsupported signal:
The input signal is not supported by this unit.
No signal:
No signal has been input.
NO ID:
Payload ID has not been superimposed.
ID:
Payload ID does not match the H/V (Horizontal/
Vertical) information of SDI signal.
CRCC:
EYE, etc. are not opened in the transmission
system, and CRCC error is found. (One of the
probable causes is that a high-frequency cable
such as 5CFB is not used.)
17
English