Spewe ES-5305 Bedienungsanleitung
Quicklinks
Zubehör zu Glühdrahtgerät
D
Découpeuse a filament chauffant
F
Trancia a filo incandescente
I
Heated Wire Cutting Device
GB
1903161 | 08-2013 | spewe.ch
Sicherheitshinweise
Bedienungsanleitung
Ersatzteilliste
Instructions de sécurité
Mode d'emploi type
Liste pièces de rechange
Avvisi di sicurezza
Istruzioni per l'uso modello
Elenco dei pezzi di ricambio
Safety Instructions
Operating Instructions
Replacement Parts
2
3-7
7/8
2
3-7
7/8
2
3-7
7/8
2
3-7
7/8
ES-5305-30 | ES-5305-40
ES- - - - 5305
ES
5305
ES
ES
5305
5305
Mod. 2013
Art.-Nr. 1200081 (30cm)
Art.-Nr. 1200082 (40cm)
1
Inhaltszusammenfassung für Spewe ES-5305
- Seite 1 Mode d’emploi type Liste pièces de rechange Trancia a filo incandescente Avvisi di sicurezza Istruzioni per l’uso modello Elenco dei pezzi di ricambio Heated Wire Cutting Device Safety Instructions Operating Instructions Replacement Parts ES-5305-30 | ES-5305-40 1903161 | 08-2013 | spewe.ch...
- Seite 2 Alimentazione: mediante trasformatore della taglierina a filo in- candescente Scope of delivery: Edge cutter type ES-5305-x0, Teflon spray, operating instructions. Delivery of ES-5305-30 with ABS suitcase, ES-5305-40 in the carton. Cutting length: 31/41 cm Cutting depth: 52 cm Equipment weight: 2.0 kg...
- Seite 3 Insert edge cutter with grey Teflon slide into vertical rail and secure clamp lever (2). Close C rail (1) with securing lever (1a). Insert edge cutter in standing equipment rear on the black case. ES-5305-30 | ES-5305-40 1903161 | 08-2013 | spewe.ch...
- Seite 4 Preferably push up the edge cutter holding the cross tube or on the clamp lever in the rear area. Fit clamp lever slightly and switch off the equipment. Do NOT press up the edge cutter on the front aluminium rail (7a). ES-5305-30 | ES-5305-40 1903161 / 08-2013...
- Seite 5 Rafter section can also be cut out on front side if the board is lying down. Position desired slope by tilting the edge cutter and fit with star handle (9). Fit rafter height with slide (6). ES-5305-30 | ES-5305-40 1903161 | 08-2013 | spewe.ch...
- Seite 6 Un angle de coupe de 90° peut être ajusté avec précision au moyen du curseur [14]. L’archetto per taglio a 90° può essere nuovamente regolato in modo esatto mediante il corsoio [14]. 90° cutting angles can be readjusted precisely with a slide [14]. ES-5305-30 | ES-5305-40 1903161 / 08-2013...
- Seite 7 Slightly loosen star handle (11) on endless coil, pull wire forward, at roundel thread from the bottom (12) and secure with simple ooze (13). Rewind excessive wire on wire coil and fit star handle (11) again. Subsequently tighten wire with star handle (4). ES-5305-30 | ES-5305-40 1903161 | 08-2013 | spewe.ch...
- Seite 8 Rondella di teflon grigia, 27x8 mm Teflon disc grey, 27x8mm 1900463 Teflonspray, 100ml Teflon spray, tin 100ml 1900521 Molla di tensione Tension spring 1200048 Coppa di trasporto ES-530x-30 / ES-600x-30 Transport bowl ES-530x-30 / ES-600x-30 ES-5305-30 | ES-5305-40 1903161 / 08-2013...