Wieland podis FCS 6 5 SI SA M32 Montageanleitung Seite 2

Installation instructions (translation from original)
®
podis
FCS 6 5 SI SA
Connection module 5-pole, screw terminals
Personnel which installs and operates or maintains this device must have read and
understood these instructions.
W AR NI NG
• Electric installations, placing devices into operation and maintenance tasks may only
be carried out by qualified electricians with relevant training in accident prevention
and at all times adhere to applicable regulations.
• Protective measures and mechanisms must correspond to applicable regulations.
• Damaged products must not be installed or operated.
• Connect or disconnect only when de-energized!
• Before performing work on the power bus or the connected components the cable
and components must be disconnected from the mains.
Handling the piercing screws:
• Use either a pneumatic or an electric screwdriver.
• Use a Torx 15 × 50 screw blade, see ordering information.
• The contact screws are correctly tightened if the depth gauge ferrules are level with
the surface of the housing.
• Do not use broken or damaged screws!
• The piercing screws must be screwed in the same position only once. If a screw is
loosened, the connection module might be connected again by on offset of a compo-
nent length on the cable. The previously terminated position with the open sheath
must be sealed with an insulation tape, see ordering information.
• Operating the module with damaged or broken screws is not permitted.
• Only original piercing screws from Wieland Electric must be used.
1 Function description
The podis ®CON FCS connection module is installed on the
the connection module, energy is taken from or fed into the tray cable without having to
cut or otherwise prepare the cable.
2 Installation dimensions (details in mm)
Type
podis® FCS 6 5 SI SA M32
podis®
FCS 6 5 SI SA RST
podis® FCS 6 5 SI SA M25
podis® FCS 6 5 SI SA RST LH
podis®
FCS 6 5 SI SA M25 LH
3 Cables
Permitted tray cables:
Article no. Type
00.729.0305.1 XPE 5G6
Tray cable conductor assignment
Conductor Color
1
gray
2 black
PE green/yellow
3
blue
4
brown
4 Installation
• The mounting point must be flat and level and must support the given load.
• Only the provided drill holes are to be used for fastening to the mounting point. The
use of additional drill holes at other points is not permissible!
® FCS 6 5 SI SA RST (LH) follow only steps 1 and 7 − 12.
For the connection module podis
For the other modules follow all steps.
Doc. # BA001058 – 06/2018 (Rev. A)
M32 75.250.0053.1
RST20i5 75.252.0053.1
M25 75.256.0053.1
RST20i5 LH 75.252.0153.1
M25 LH 75.256.0153.1
N OTE
N OTE
podis ® 5G6 tray cable. With
L × W × H [mm] HO [mm]
250 × 84 × 74 41
217 × 84 × 74 41
245 × 84 × 74 41
217 × 84 × 59 34
245 × 84 × 59 34
N OTE
Wieland Electric GmbH
Brennerstraße 10–14
96052 Bamberg
Tel.: +49 (951) 9324-0
Fax: +49 (951) 9324-198
Internet: www.wieland-electric.com
Email: info@wieland-electric.com
1. Undo the four screws of the housing and open the cover.
2. Fix the cable gland M25 with 3.5 Nm (15.5 lb-in) and M32 with 5.0 Nm (22.2 lb-in).
3. Strip the sheath from the round cable for a distance of approx. 180 mm.
4. Feed the round cable through the gland and tighten the gland.
5. Remove 12 mm of insulation from the single conductor wires.
6. Connect the individual strands to the respective screw clamps (torque 1.2 Nm /
10.6 lb-in).
7. Fasten the module by means of two fastening screws M5/M6 securely to the under-
ground. Use shims.
8. Undo both screws in the bottom part of the housing.
9. Open the housing top upwards.
10. Consider the mechanical coding of the tray cable. Fit the bottom section of the
housing and insert the tray cable. Check the correct orientation. Tilt the housing
closed again and tighten the two screws (torque 1.2 Nm / 10.6 lb-in).
11. Screw all the contact screws into the tray cable (torque 2.0 Nm).
12. Close the cover of the housing and tighten the four screws (torque 1.2 Nm /
10.6 lb-in). Make sure that no wires are squeezed between the cover.
Wire length
L1 brown
L2 black
L3 grey
N blue
PE green/yellow
5 Disassembly
For disassembly of the connection module proceed in reverse order as described in
"4 Installation". In doing so, take note of the associated safety information. Note especial-
ly that working under load is specifically prohibited.
6 Technical data
Connection data
Rated voltage / Test voltage / Overvoltage category
Rated voltage acc. to UL
Rated current
•
podis® FCS 6 5 SI SA M25
•
podis® FCS 6 5 SI SA M32
•
podis® FCS 6 5 SI SA RST
•
podis® FCS 6 5 SI SA RST LH
•
podis® FCS 6 5 SI SA M25 LH
Rated cable size
Connection type
Wire range
• stranded with ferrule
•
podis® FCS 6 5 SI SA M25 LH stranded with ferrule
Stripping length
General data
Operating ambient temperature
Installation temperature
Protection rating (in locked condition)
7 Ordering information
Accessories
Cable gland M25 × 1.5 black, for round cable with
• cable diameter 9 – 16 mm (not for UL installation)
• cable diameter 13 – 18 mm
Backnut M25 × 1.5 black
Cable gland M32 × 1.5 black, for round cable with
• cable diameter 10 – 21 mm
• cable diameter 18 – 25 mm
Backnut M32 × 1.5 black
Multi-feed-through
• for M25, Z5.507.1553.1, 3 × 8 mm
• for M25, Z5.507.1553.1, 4 × 7 mm
• for M32, Z5.507.1653.1, 2 × 8 mm
Tools
Screwdriver bit Torx 15
Spare / repair parts
Insulating sealing tape
podis®
FCS 6 5 SI SA
140 mm, 5.5 in
80 mm, 3.1 in
120 mm, 4.7 in
90 mm, 3.5 in
180 mm, 7.1 in
690 V AC / 6 kV / 3
600 V AC
IEC
41 A
(max. 40 °C)
41 A
(max. 40 °C)
20 A
20 A
20 A
6 mm²
Screw terminals
1.5 – 16.0 mm², AWG 16 – 6
1.5 – 4 mm², AWG 16 – 12
12 mm
-25 °C ... +55 °C
-13 °F ... +131 °F
+5 °C ... +40 °C
+41 °F ... +104 °F
IP65 acc. to EN 60529
NEMA Type 1
Z5.507.1453.1
Z5.507.1553.1
05.505.0253.1
Z5.507.1753.1
Z5.507.1653.1
05.505.0353.1
05.512.4883.0
05.512.5083.0
05.512.4383.0
06.502.6210.0
Z6.653.7800.0
EN