Saving; Saving Your Settings; Saving A Program; Registering Programs In The Category/ Favorites Buttons - KingKORG XMT Bedienungsanleitung

continue. (PG: "5. GLOBAL parameters")
1.
Hold down the SHIFT/EXIT button and press the PROGRAM
(GLOBAL) button.
You'll enter Global mode, and the PROGRAM (GLOBAL) button
will blink.
2.
Use the PAGE +/- buttons to select the GLOBAL "u01: Utility"
page item Load Preload, and press the value dial.
3.
Turn the value dial to select the type of data that will be
restored to its factory-set condition.
1Program: Data of the currently selected program
ALL Program: Data for programs 1–200
Global: Global data
All Data: Programs 1–200 and global data
4.
Press the value dial; a confirmation screen will appear.
TIP: If you decide not to load the data, press the SHIFT/EXIT
button or the PROGRAM (GLOBAL) button.
5.
Press the value dial once again.
When the selected data has been loaded, the display will
indicate "Completed!" and you will automatically return to the
top screen.

Saving

Saving your settings

If you want to keep the global settings or programs that you've
edited, you must save them to internal memory.
If you turn off the power without saving, any changes that
you've made to the global settings will be lost. Be sure to save
your edited settings if you want to use them in the future.
If you've edited a program, the changes you've made will be
lost if you select another program or turn off the power
without saving. Be sure to save your edited settings if you
want to use them in the future.
You can't save your settings if memory protect is turned on.
Turn off memory protect before you proceed. (PG: "5.
GLOBAL parameters")
1.
Saving global settings
Which settings are saved?
When you save global data, the following settings are saved.
₋ All parameters in the GLOBAL "g01–g44" pages
The state of the OCTAVE UP/DOWN buttons is not saved. The
TUBE BOOST button and TUBE ON button settings are saved
as global parameters.
To save the global settings, proceed as follows in Global mode.
1.
Hold down the SHIFT/EXIT button and press the PROGRAM
(GLOBAL) button to enter Global mode.
The main display will show the global parameter edit screen,
and the PROGRAM (GLOBAL) button will blink.
2.
Press the WRITE button.
The main display will show a confirmation screen, and the
WRITE button will blink.
TIP: If you decide not to save, press the SHIFT/EXIT button at
this point.
3.
Press the WRITE button once again.
When the data has been saved, the display will indicate
"Complete!" and you will return to the previous screen.
Never turn off the power while data is being saved. The
data may be destroyed if you do so.
2.

Saving a program

Which settings are saved?
When you save a program, the following settings are saved.
₋ All parameters in PROGRAM "p01–06 (Program), s01–80 (Synth),
v01–18 (Vocoder), a01–12 (Arp)"
₋ Master effect settings (PRE FX, MOD FX, REV/DELAY)
The status of some of the front panel settings will not be saved
(the selected state of the TIMBRE A/B select buttons,
OSCILLATOR select button, LFO select button)
The state of the OCTAVE UP/DOWN buttons will not be
saved.
Since TUBE and EQ are global effects that apply to all
programs in common, their settings are not saved for each
program.
To save a program, proceed as follows in Program mode.
1.
Press the WRITE button.
The main display will show a screen allowing you to specify the
save‐destination, and the WRITE button will blink.
2.
Turn the value dial to select the storage location (program
number).
TIP: If you decide not to save the program, press the SHIFT/
EXIT button at this point.
3.
Press the WRITE button once again.
When the data has been saved, the display will indicate
"Complete!" and you will return to the previous screen.
Never turn off the power while data is being saved. The
data may be destroyed if you do so.
3.
Registering programs in the category/
favorites buttons
The KingKORG provides a convenient Favorites function that lets you
recall a program by pressing a single button. This can be very convenient
when you're playing live. In order to use this function, you'll need to
register your favorite programs in the category/favorites buttons.
1.
Select a program that you want to register. (OM: p.13 "Selecting
a program")
2.
Hold down the WRITE button and press the FAVORITES
button.
The FAVORITES button and all of the category/favorites buttons
will blink.
Saving
21