HERRMANS H-BLACK PRO DYNAMO Bedienungsanleitung

1. Multi-joint bracket 4. Dual cable, electric connection to dynamo
2. Screws for 4mm Allen key 5. Dual cable, electric conection to rear lamp
3. Rotating ON/OFF switch 6. Click in E I A, K front reflector
25
24
23
General information:
22
Congratulations! You are a member of the selected group of individuals biking with the
21
HERRMANS® technically advanced LED lamp – H-Black Pro – specially developed for the
demanding climate of northern Europe. The H-Black Pro dynamo head lamp is equipped
20
with the new patent pending Projector Technology (P-Tech) – automotive technology
19 transformed to the bicycle. The P-Tech feature o ers extremely high optical e ciency and
exact 100% guiding of light. Resulting in superior light output and a focused light beam with
18
a sharp cut of line. -> More light on the road (where needed).
17 The LED lamp produces a clear, white light reminiscent of daylight. The light-emitting diode
is maintenance-free and none of the lamp parts will need replacing. In addition, the
16
electronics are protected against any eventual overvoltage from the dynamo, even when no
rear light is connected.
15
The light pattern is optimized for the rider - super wide, long, and homogeneous light
14
distribution (one of the widest on the market) – with an output of up to 200 lumens. The
lamp o ers near field illumination as well as non-flickering illumination even at low speeds.
13
To be seen by other tra c the H-Black Pro Dynamo has additional LEDs for clear side
12
visibility.
H-Black Pro is designed only to be powered by dynamo 6V (AC voltage). Please note,
11
dynamo not included with product. A separate version is available for e-bikes (DC).
10
H-Black Pro is equipped with Stand light function and a distinct ON/OFF switch that is easy
to operate.
9
The lamp works with all conventional dynamo rear lamps. This means that the rear lamp can
8
be controlled by H-Black Pro ON/OFF switch when the lamps are connected together.
7
The small, elegant contemporary alloy housing (CNC) provides robustness and excellent
cooling of the LED. The lamp has a click-in E I A, K front reflector.
6
The "Made in Finland" label is a guarantee of quality. Further evidence of H-Black Pro
5
quality is its compliance with the stringent requirements of the German StVZO certificate
4
3
2
1
Light spread when H-Black Pro is mounted on
top of the front fork of a standard men´s bicycle.
USER MANUAL H-BLACK PRO DYNAMO
(Road Tra c Licensing Regulations). We wish you good visibility on your bike rides!
Assembly:
Make sure that the cables run smoothly through the front bracket (1) as displayed in the
image. Fasten the bracket (1) to the front fork of the bicycle. If your bicycle has a lamp
bracket on the side of the front fork, the lamp can be mounted there without using the
supplied bracket. Angle the lamp according to the area you want lit up. When mounting the
lamp, it is important not to aim it so high that it dazzles on-coming tra c. Tighten the screws
(2) securely to prevent the lamp from moving on its own. Route the dual cable (4) to the
(hub-) dynamo and attach it as described in the dynamo instructions. It does not make any
di erence which way the cables are installed (+/-). The minus (-) cable has a light grey line,
the plus (+) cable is plain black. From the other dual cable (5), you can route cables to your
dynamo rear lamp so that it can also be controlled by the H-Black Pro switch (3). It is
possible to attach an E I A, K approved front reflector (6) through a click-in system.
Please note that the lighting equipment must not be concealed.
Functions:
Side visibility: The main light source and optical reflector are optimized for lighting up the
road for the biker. The second light source - two diodes on the sides of the optical reflector -
are aimed to the sides, optimized to make the bike visible to other tra c from the sides
without dazzling.
Stand light: Part of the dynamo energy is stored in a condenser when you are riding and is
fully loaded after only approx. 3 minutes. When the bike stops, the main light source and the
side light sources run for several minutes with the power from the condenser.
Herrmans Oy Ab +358 20 134 5100
PB36 herrmans@herrmans.eu
68601 Jakobstad, Finnland www.herrmans.eu
The light beam must be inclined so that at a 5m distance
the center of the light beam is only half as high as the
mounted lamp.
www.herrmans.eu
www.herrmans.eu
www.herrmans.eu
www.herrmans.eu
EN
http://www.nordiclights.com
http://www.nordiclights.com
http://www.nordiclights.com
http://www.nordiclights.com