Seite 1
Instruction Manual DC300/DC310 Digital Underwater Camera Set...
Seite 2
MUST DO 1. Read warnings in manual (pages 6-8). charge at room temperature up to 10% per day. Store batteries in 2. If you have any questions after reading plastic bag or container in refrigerator this manual or problems regarding the or cool, dry place.
Seite 3
Limited Warranty This product will be replaced or repaired free of charge within 1 year from the purchase date in the case of a manufacturing defect, if the complete defective product is sent freight prepaid at the sender’s risk with prepayment for handling and shipping of US$10.00 to: Pioneer Research, Attn: SeaLife Service C enter, 97 F oster Road, Suite 5, Moorestown, NJ 08057, or to the SeaLife distributor in your country of residence.
Seite 4
WARNING Only use SeaLife AC power adapter item #SL13132 with 3.3 volt DC out- put. Using any other AC adapter will damage the camera.. The inner camera is not waterproof or water resistant. Use the inner cam- era only inside the SeaLife waterproof housing when in or around water. Follow waterproof housing instructions carefully to prevent water damage to camera.
Seite 5
WARNING Do not insert or drop any objects into the SD memory card or battery slots. This may cause a fire or an electrical shock. Do not attempt to modify this camera. This may cause a fire or an electrical shock. Do not remove the camera casing.
Seite 6
WARNING WARNING Handle the camera carefully and do not bump the camera into any hard object. Handling the camera roughly may cause a malfunction. Do not move the camera while it is attached to AC adapter, USB or video cable. (If you are using the AC power adapter, unplug the adapter from the AC power outlet after you have switched off the camera.) Ensure that any connector cords or cables to other devices are disconnected before moving the camera.
Seite 7
® trademarks of M GI Software C orp. ® ■ Adobe, the Adobe logo, and Acrobat are trademarks of Adobe Systems Incorporated. ■ SeaLife , Reefmaster , Land & Sea are registered trademarks of ® ® ® Pioneer Research.. ■ Other names and products may be trademarks or registered trademarks of their respective owners.
How It Works - A Very Unique Camera Land & Sea ® The SeaLife Reefmaster Digital Land & Sea camera allows you to choose between Land Mode for taking land pictures, Sea Mode for taking underwater pictures and Flash mode for taking underwater pictures with your SeaLife External flash (optional accessory).
Seite 11
Land Mode: If you are taking land pictures, set the camera to Land Mode. Now the camera is automatically programmed to take great land pictures. The camera evaluates light conditions through the lens. If it’s too dark, the camera uses the built-in flash to fire a pre-flash (to test the picture quality) and a primary flash for taking a properly exposed picture.
Package contents C arefully unpack your package and make sure that you have the following items. C ommon Product C omponents: ■ Digital camera ■ Software C D-RO M ■ Video cable ■ C amera strap ■ Quick Guide ■ C amera C arry C ase ■...
Mode dial 1. Record mode 2. Playback mode (Review) 3. Setup mode 4. Movie mode Mode Description Record Mode Use this mode to capture still images. Playback mode Use this mode to view images & videos, (Review) delete images & video clips, view a slide show, view thumbnail displays.
LCD monitor information in Record mode These indicators are displayed when recording still images: in Land mode* Land mode Sea mode Flash mode 1. Exposure Program mode 8. External Flash Exposure Modes Macro - For correct image Land mode exposure inside 2 feet (60cm) Sea mode shooting distance when using Flash mode...
Seite 17
These indicators are displayed when recording video clips: 1. Movie mode 2. Battery level Full battery power Medium battery power Virtually no battery power 3. Recordable movie time 4. Card indicator 5. Time (24-hour-format) 6. Date (year-month-day) These indicators are displayed when playing images back: 1.
GETTING STARTED You can use either 2 AA size batteries (High-Energy Alkaline, Ni-MH, Lithium) or an A C power adapter (optional accessory) to power the camera. Battery power is convenient for recording images or video clips while A C adapter power is recommended for transferring images to your computer.
Loading a SD memory card (optional accessory) The camera comes with 8M B of internal memory, allowing you to store images and video clips in the camera. However, you can expand the memory capacity by using an optional SD memory card so that you can store additional images and video clips.
Choosing the language 1. Select a language that you prefer by using the button. 2. Press the OK button to confirm. • The language setting will be retained even if the camera is turned off. • The provided languages are [English], [Français], [Deutsch], [Español], [Portugués], [Italiano], ], [ ], and [ Setting the date and time...
Setting the image resolution and quality Resolution and quality settings determine the pixel size (dimension), image file size, and compression ratio for your image. These settings affect the number of images that can be stored in internal memory, or on an SD memory card. Higher resolution and higher quality images offer the best photographic results but take up more memory space.
RECORD MODE Taking pictures Your camera is equipped with both an optical viewfinder and a 1.6" LC D monitor to compose images. Taking images using the optical viewfinder will con- serve battery power. If your batteries are low, it is recommended that you only compose images by using the viewfinder.
Seite 23
Using the LCD monitor and QUICK REVIEW mode 1. O pen the lens cover. 2. Turn the mode dial to mode. 3. Turn the camera on by pressing the button. 4. By pressing the button repeatedly in mode when quick view is O N, the LC D status will change cyclically.
Seite 24
Using the macro focus setting Use the macro focus setting to shoot a close-up of the subject on land, such as flowers or insects. The effective range is between 2 to 3ft (60 to 90 cm). 1. O pen the lens cover, turn the mode dial to the mode, and power on the camera.
Using the digital zoom By using the digital zoom, images can be enlarged so that the subject appears closer. However, the more the image is enlarged, the grainier the image will become. The digital zoom function is only available when you set the LC D monitor and the digital zoom to O N.
Using the self-timer The self-timer duration is 10 seconds. After the activation of the self-timer by pressing the shutter button, the self-timer lamp starts blinking slowly for 7 sec- onds and then blinking faster for the rest of 3 seconds. This allows you to get into the scene when taking group images.
Flash Modes The camera has four flash modes: Automatic Flash (default), Red-Eye Reduction, Fill Flash (on), and Flash Off. The modes appear cyclically when you press the button on the rear side of the camera. The table below will help choose the appropriate flash mode: Flash Mode Description...
Taking pictures manually You can manually adjust conditions such as EV compensation, white balance, or IS O speed when taking pictures. For EV compensation, white balance, or IS O speed information, refer to Exposure, White balance, or IS O in the Record menu. To take pictures manually: 1.
PLAYBACK MODE (Review images) In the mode, you can view, magnify, delete images, play video clips, or run a slide show. Playback mode also provides a thumbnail image display, allowing you to quickly search for the image you want. Viewing images You may view your images without opening the lens cover since the lens is not used for playback.
Zoom Playback While reviewing your images, you may enlarge a selected portion of an image. This magnification allows you to view fine details. 1. Turn the mode dial to the mode and power on the camera. 2. Select the image that you want to view by using button.
Displaying thumbnail images This function allows you to view nine thumbnail images on the LC D monitor simultaneously so you can quickly scan for a particular image. 1. Turn the mode dial to the mode and power on the camera. 2.
Protecting one image/video clip You can protect the image/video clip from being accidentally erased by using the protect function in the Playback menu. Follow the steps below to perform protect function: Protecting one image/video clip 1.Turn the mode dial to mode and power on the camera.
Setting DPOF DP O F allows you to embed printing information on your memory card. By using DP O F, you can select an image to be printed and then specify how many prints you would like. Take your memory card to a DP O F enabled printer that accepts SD memory cards.
Seite 34
To delete all images/video clips at once: 1. Turn the mode dial to mode and power on the camera. 2. Press the button on the rear side of the camera. 3. Select Delete all by using the button. 4. Press the button.
MOVIE MODE Recording video clips The movie mode allows you to record video clips at the resolution of 320 x 240 pixels. 1. O pen the lens cover, turn the mode dial to the mode, and power on the camera. ■...
Viewing video clips To view the recorded video clips, follow the steps below. 1. Turn the mode dial to mode and power on the camera. 2. Select the video clip that you want to view by using the button. 3. Press OK to start. ■...
TRANSFERRING RECORDED IMAGES TO YOUR COMPUTER You can share recorded images/video clips with your family or friends via e-mail or post them on the Web. First, you need to connect the camera to your com- puter by using the USB cable and then transfer the images/video clips. To transfer images/video clips from the camera to your computer, follow the steps below.
Step 1: Installing the USB driver on Windows computers Installing the The USB driver on the supplied C D-RO M is only needed for Windows 98. USB driver on computers running Windows 2000/ME/XP is not necessary. 1. Insert the C D-RO M packaged with the camera into the C D-RO M drive.
Step 3: Downloading images/video clips When the camera is turned on and connected to your computer, it is considered to be a disk drive. You can download images/video clips by copying them from the “removable disk” (“untitled” disk on a Macintosh) to your hard drive or to another kind of disk.
INSTALLING MGI PHOTOSUITE ® M GI PhotoSuite is a very user-friendly image-editing program. With PhotoSuite, you can easily retouch, compose and organize your images. It contains a variety of templates, such as photo frames, birthday cards, calendars and more. G et your images ready and go explore this amazing program. ®...
INSTALLING MGI PHOTOVISTA ® ® M GI PhotoVista is an easy-to-use program that lets you create spectacular 360° panoramic images in a snap. When you view these panoramas, you get the experience of being totally immersed in a realistic environment. PhotoVista’s powerful engine quickly and automatically stitches images together, and its intuitive interface will let even a novice get great results in minutes.
INSTALLING THE USER’S MANUAL In an effort to conserve energy and preserve our world’s forests and wildlife, this manual is only provided on the C D-Rom in PDF format. suggest you read through the instruction manual and print only those pages you need for future reference.
INSTALLING ACROBAT READER For Windows users: 1. Insert the C D-R O M that came with the camera into your C D-RO M drive. The welcome screen appears. 2. Click “Install Acrobat Reader.” Follow the on- screen instructions to complete the installation. For Mac users: 1.
MENU OPTIONS Record menu You can use the Record menu to select image size, image quality, IS O speed, Quick View or digital zoom. You can also adjust exposure, white balance, or LC D brightness in the Record menu. The Record menu even allows you to enable digital zoom or quick view function.
White balance Your camera adjusts the white balance of each scene automatically. However, the images that your camera captures will appear different under different light- ing conditions (daylight, cloudy, sunset, tungsten, fluorescent lights). Unlike your eyes, which can easily adjust to different lighting conditions (lighting tem- peratures), a digital camera cannot always differentiate between lighting types.
Quick view By enabling quick view, you can temporarily view the image on the LC D moni- tor right after you take a picture. After a temporary preview, the camera returns mode automatically. To enable quick view, first press the button. Then select [On] by using the button and press O K.
Playback menu Use the Playback menu to create an on-camera slide show, configure DP O F settings, or transfer images to a memory card. You can also use the Playback menu to protect an image, delete all images at once, or adjust the LC D brightness.
Setup menu Select between Land & Sea exposure programs and other general camera preferences in the SET-UP mode. Turn the mode dial to SET-UP mode and nav- igate to the option you wish to configure by using the button. LAND & SEA EXPOSURE PROGRAM SETTING ®...
Format This option formats the internal memory (or memory card ) and erases all stored images and data. To perform the format function, first press the button. Then select [Yes] by using the button and press OK. A progress bar displays, showing the progress of formatting.
Reset to default If you wish to restore all camera settings to their original status, select this option and then press the button. Select [Yes] by using the button and then press OK. The table below shows the default setting for each item. Item Description Image size...
Date imprint If you set imprint function, your image will be displayed with date on it. To enable this function, first press the button. Then select [Yes] by using the but- ton and press OK. Video out You can view your images on a TV. Remember to select correct video output type according to where you locate.
Underwater Housing Instructions Important: Please carefully read and understand these instructions before using camera and housing underwater. DC300: SeaLife Reefmaster Dive Easy DC300/ Housing (SL113) DC310 • Depth rated and tested to 200ft. (60M) • Fully rubbered armored for water and shock protection.
MUST DO for underwater housing: 1. Read these instructions before using the underwater housing. 2. Do not exceed the depth rating printed on the lens port of the housing. 3. Keep main O-Ring perfectly clean. • Clean main O-ring with cleaning brush provided before every use. Do not remove O-ring.
Seite 56
Open view of housing The housing uses one O-ring to form a waterproof seal C ontact SeaLife Service C enter if O-ring is damaged and requires replacement. Important: C arefully inspect o-ring for salt, sand, hair, cuts, tears or other damage.
Seite 57
Main O-ring and keeping a waterproof seal The SeaLife housing uses one O-ring to form a waterproof seal. Every housing is tested for quality and a waterproof seal. It is your responsibility to maintain the housing and ensure it remains waterproof. Our research and testing shows that 99% of leaks are the result of not cleaning or caring for the O-ring.
Seite 58
SeaLife ReefMaster Underwater Camera Housing Front View...
Seite 59
SeaLife ReefMaster Underwater Camera Housing Rear View of DC300 Dive-Easy housing (item #SL113) Monitor frame for attaching optional sunshade. External Flash Exposure control. When camera is set to External Flash mode, press the LCD button to select between: Macro Flash - for optimal exposure of pictures inside 2’...
SeaLife ReefMaster Underwater Camera Housing Rear View of DC310 Advanced housing (item #SL118) Mode dial Select between Record, Playback, Movie and Set-Up modes. Navigation buttons thumbnails External Flash Exposure control. Right Left Timer When camera is set Flash to External Flash...
How to set-up the Underwater Housing Set up camera 1. Insert 2 fully charged Ni-MH batteries (size AA, capacity at least 1800 mAh). See page 68 for more battery information. Make sure you insert the batteries with the correct + and – polarity. 2.
Seite 62
Do not allow any water droplets to get inside housing. This will cause the inside of the housing to fog. Close housing lid tightly. Make sure there are no obstructions that prevent the housing from closing. Make sure lid is tightly pressed into housing, ( see picture).
6. Never store camera or housing in direct sunlight or in a dark damp area. The airtight, unbreakable SeaLife ReefMaster Dry C ase (Item # SL930) is highly recommended along with 1-oz bags of SeaLife Moisture Muncher Desiccant...
Great Pictures Made Easy Taking underwater pictures is much different that taking land pictures. Here are the most important tips to taking great pictures underwater: 1. Crystal Clear water. Crystal Clear water is essential for good underwater pictures. Remember the human eye can see more detail than a camera.
Seite 65
5.Take several pictures of the same subject. Use different distances and angles. (Allow about 10 seconds between shots for the flash to re-charge). Study and compare the good and bad pictures and you will soon be a master. Never touch any sea creatures. Consult your dive master about approaching dangerous creatures or structures.
Battery Selection Guide: It is important to use only AA batteries designed for high drain electronic devices. Nickel Metal Hydride (Ni-MH) We suggest using SeaLife 1800 mAh Ni-MH rechargeable batteries or higher mAh rated Ni-MH battery. With Ni-MH batteries, you can expect about 2 hours of normal operating usage.
Seite 67
Battery Life We have tested the following batteries under normal and extreme operating conditions. The following operating times are averages and can vary depend- ing on age of battery, temperature and other factors. Normal conditions (designed to simulate operating conditions when scuba diving): 1.
Trouble shooting guide Problem Possible cause Corrective Action No Power Battery power low ... Replace or recharge batteries. Wrong type of batteries..Use only AA designed for high drainage electronics.
Seite 69
Problem Possible cause Corrective Action Grainy picture Dark light conditions..Move closer to subject (2’ to 6’). Use SeaLife External Flash to illuminate subject and improve color and brightness. Overexposed image To close to reflective object..Move farther away from sub- ject (4’...
HINWEISE ZU WARENZEICHEN Microsoft ® und Windows ® sind in den USA eingetragene Warenzeichen der Microsoft Corporation. Pentium ® ist ein eingetragenes Warenzeichen der Intel Corporation. Macintosh ist ein Warenzeichen der Apple Computer, Inc. ist ein Warenzeichen. PhotoSuite, PhotoVista und das MGI-Logo sind Warenzeichen oder eingetragene Warenzeichen der MGI Software Corp.
Seite 71
WARNUNG Benutzen Sie diese Kamera nicht, wenn Rauch entweicht, wenn sie ungewöhnlich heiß wird, wenn sie ungewöhnliche Geräusche oder Gerüche verursacht oder wenn sie in anderer Hinsicht Fehlfunktionen aufweist. Eine weitere Benutzung unter diesen Umständen birgt Brand- und Stromschlaggefahr. Schalten Sie die Kamera sofort aus und unterbrechen die Stromversorgung (entnehmen die Batterien oder den AC-Netzadapter).
Seite 72
VORSICHTSHINWEISE Bewahren Sie die Kamera nicht in einer feuchten oder Staubigen Umgebung auf. Es besteht Brand- und Stromschlaggefahr. Legen Sie die Kamera nicht an einen Ort, an dem Öl- und Wasserdampf entstehen (z.B. in der Nähe eines Kochherdes oder Luftbefeuchters). Es besteht Brand- und Stromschlaggefahr.
Seite 73
INHALT Aufnahmen mit dem digitalen EINFÜHRUNG ....7 Zoom ........19 Überblick ......... 7 Aufnahmen mit dem Packungsinhalt ......7 Selbstauslöser ......20 Optionales Zubehör ....7 Aufnahmen im Makro-Modus .. 21 LERNEN SIE DIE KAMERA Aufnahmen mit dem Blitz ..21 KENNEN ......
Seite 74
Setup-Menü ......41 Installation des USB-Treibers bei Formatieren ........41 Macintosh ........ 33 Signalton ........41 Schritt 2: Schließen Sie die Aus ..........41 Kamera an den Computer an. 33 Standard laden ....... 42 Schritt 3: Laden Sie die Datumstyp ........42 Fotos/Video-Clips herunter.
EINFÜHRUNG Überblick Diese neue Ditigalkamera liefert Ihnen mit einem 3,3-Megapixel CCD-Imager Bilder von sehr hoher Qualität mit einer Auflösung von 2048x1536. Sie können die Aufnahmen entweder durch den optischen Sucher oder auf dem 1,5" TFT-Farbmonitor arrangieren und sie dort bis ins Detail durchgehen. Ein Sensor für den automatischen Blitz mißt die Lichtbedingungen der Aufnahme und entscheidet, ob ein Blitz zugeschaltet werden soll oder nicht.
Modus-Schalter Modus Beschreibung Aufnahme-Modus In diesem werden Fotos aufgenommen. LED-Anzeigen Wiedergabe-Modus In diesem Modus können Sie sich Bilder/Videoclips ansehen und löschen, sich eine Diashow oder die Thumbnail-Bilder ansehen. Film-Modus In diesem Modus werden Videoclips aufgenommen. Setup-Modus In diesem Modus werden die Kameraeinstellungen vorgenommen.
Informationen zum LCD-Monitor Diese Angaben finden Sie auf dem LCD-Monitor bei der Aufnahme von Fotos: 1. Aufnahme-Modus 8. Belichtungskorrektur 2. Batterieladestand 9. Anzahl möglicher Aufnahmen (bei der aktuellen Einstellung Batterie voll von Größe und Qualität) Batterie halbvoll Batterie fast leer 10.
Seite 80
Diese Angaben finden Sie auf dem LCD-Monitor bei der Aufnahme von Videoclips: 1. Film-Modus 2. Batterieladestand Batterie voll Batterie halbvoll Batterie fast leer 3. Mögliche Aufnahmedauer 4. Kartenanzeige 5. Zeit (24-Stunden) 6. Datum (Jahr-Monat-Tag) Diese Angaben finden Sie auf dem LCD-Monitor bei der Wiedergabe von Fotos: 1.
ERSTE SCHRITTE Einsetzen der Batterien Die Kamera kann entweder mit zwei Batterien des Typs AA (Alkali, Ni-MH) oder über einen AC-Netzadapter (optionales Zubehör) mit Strom versorgt werden. Beim Aufnehmen der Bilder und Videoclips ist es praktisch, die Kamera mit Batteriestrom zu versorgen, die Versorgung über den AC-Netzadapter wird empfohlen bei der Datenübertragung auf den Computer.
Das Einsetzen einer SD-Speicherkarte (optionales Zubehör) Die Kamera verfügt über einen internen Speicher von 8MB, auf dem die aufgenommenen Fotos und Videoclips gespeichert werden können. Sie können die Speicherkapazität jedoch erhöhen, indem Sie eine optionale SD-Speicherkarte einsetzen. Dann können Sie noch mehr Fotos und Videoclips gespeichert werden.
Auswahl der Sprache Wenn Sie das erste Mal die Kamera einschalten, erscheint das Fenster für die Spracheinstellung. HINWEIS Sie werden aufgefordert eine Sprache für die auf dem LCD-Monitor angezeigten Informationen auszuwählen. Die Sprache des OSD-Menüs (On- Screen Display) wird folgendermaßen eingestellt. 1.
Bildauflösung und Qualität einstellen Die Einstellung von Auflösung und Bildqualität bestimmt die Pixelgröße (Abmessung), die Größe der Bilddatei und das Komprimierungsverhältnis der Bilder. Diese Einstellungen haben einen Einfluß auf die Anzahl der Bilder, die im internen Speicher oder auf einer SD-Speicherkarte gespeichert werden können. Bei einer höheren Auflösung und einer besseren Bildqualität werden bessere fotografische Ergebnisse erzielt, die Dateien verbrauchen aber mehr Speicherplatz.
AUFNAHME-MODUS Fotografieren Die Kamera ist sowohl mit einem optischen Sucher als auch einem 1,5" LCD-Monitor Die Verwendung des Suchers ausgestattet, über die Sie die Bilder arrangieren können. Der Vorteil des optischen Suchers liegt im geringeren Stromverbrauch. Wenn die Batterien fast leer sind, sollten Sie nur noch den optischen Sucher verwenden.
Die Verwendung des LCD-Monitors 1. Öffnen Sie den Objektivschutz. 2. Stellen Sie den Modus-Schalter auf 3. Schalten Sie die Kamera ein, indem Sie auf HINWEIS drücken. 4. Schalten Sie den LCD-Monitor ein, indem Sie drücken. 5. Arrangieren Sie das Bild. 6.
Aufnahmen im Landschafts-Modus Der Landschafts-Modus ist geeignet für die Aufnahme von Landschaften und wenn sich das Fotoobjekt zwischen 1,9 m und unendlich weit von der Kamera entfernt befindet. 1. Öffnen Sie den Objektivschutz und drehen Sie Aufnahmen mit dem digitalen Zoom den Modus-Schalter auf .
Aufnahmen mit dem Selbstauslöser Die Auslöseverzögerung beim Selbstauslöser beträgt 10 Sekunden. Nachdem der Selbstauslöser durch Drücken des Auslösers aktiviert wurde, blinkt die Selbstauslöserlampe sieben Sekunden lang langsam, die restlichen drei Sekunden schnell. Bei dieser Funktion können Sie sich selbst mit auf dem Foto aufnehmen lassen.
Aufnahmen im Makro-Modus Im Makro-Modus werden Nahaufnahmen des Fotoobjekts gemacht wie etwa von Blumen oder Insekten. Der effektive Bereich liegt zwischen 0,55 und 0,9 m. 1. Öffnen Sie den Objektivschutz und drehen Sie den Modus-Schalter auf . Schalten Sie dann die Kamera ein. 2.
Die Kamera verfügt über vier Blitzmodi: Automatischer Blitz (Standardeinstellung), Vorblitz zur Verringerung des Rote-Augen-Effekts, Blitz Ein und Blitz Aus. Wenn Sie wiederholt auf die Taste an der Rückseite der Kamera drücken, erscheinen die Blitzmodi in zyklischer Reihenfolge auf dem LCD-Monitor. Die folgende Tabelle hilft Ihnen dabei, den geeigneten Blitzmodus auszuwählen: Blitz-Modus Beschreibung...
Aufnahmen manuell einstellen Sie können Belichtungskorrektur, Weißabgleich oder die ISO-Empfindlichkeit für die Aufnahmen auch manuell einstellen. Informationen zu Belichtungskorrektur (EV- Kompensation), Weißabgleich und ISO-Empfindlichkeit finden Sie im Aufnahmemenü unter Belichtung, Weißabgleich und ISO. Aufnahmen manuell einstellen: 1. Öffnen Sie den Objektivschutz und drehen Sie den Modus-Schalter auf .
WIEDERGABE-MODUS Wiedergabe von Bildern -Modus können Sie sich die Bilder anzeigen lassen, sie vergrößern oder löschen, Videoclips wiedergeben oder eine Diashow starten. Im Wiedergabe-Modus können Sie sich die Bilder auch als Thumbnails anzeigen lassen, mit denen Sie die Bilder schnell überfliegen können. Da das Objektiv nicht für die Wiedergabe der Bilder benötigt wird, müssen Sie dazu das Objektiv nicht öffnen.
Wiedergabe mit Zoom Während der Wiedergabe der Bilder können Sie einen bestimmten Bereich vergrößern. Dadurch können Sie auch Details der Aufnahme sehen. 1. Drehen Sie den Modus-Schalter auf schalten Sie die Kamera ein. 2. Mit der Taste wählen Sie das Bild aus, das Sie sich ansehen möchten.
Anzeige von Thumbnail-Bildern Mit dieser Funktion können Sie auf dem LCD-Monitor neun Thumbnail-Bilder gleichzeitig anzeigen lassen, so daß sie einfacher nach einem Bild suchen können. 1. D re h e n S i e d e n M o d u s - S c h a l t e r d e n entsprechenden Modus und schalten Sie die Kamera ein.
Löschschutz eines Bilds/Videoclips Löschschutz eines Bilds/Videoclips Sie können ein beliebiges Bild/Videoclip mit der Löschschutz-Funktion im Wiedergabe- Menü vor dem versehentlichen Löschen schützen. Gehen Sie dazu so vor: 1. Drehen Sie den Modus-Schalter auf schalten Sie die Kamera ein. Dei zuletzt gemachte Aufnahme eines Fotos/Videoclips wird auf dem LCD-Moni- tor angezeigt.
DPOF-Einstellungen Mit der DPOF-Funktion können Sie Druckinformationen auf der Speicherkarte speichern. Mit DPOF können Sie festlegen, welches Bild in welcher Anzahl gedruckt werden soll. Stecken Sie die Speicherkarte in einem Drucker mit DPOF-Funktion, der SD-Speicherkarten unterstützt. Der DPOF-/Kartenkompatible Drucker liest die auf der Speicherkarte gespeicherten Informationen und druckt die Bilder wie festgelegt aus.
Löschen von Bildern/Video-Clips Ein einzelnes Bild/einen einzelnen Videoclip löschen: Wenn Sie ein einzelnes Bild/Videoclip löschen möchten, verwenden Sie die Taste die sich an der Rückseite der Kamera befindet. Wenn Sie alle Bilder/Videoclips gleichzeitig löschen möchten, gehen Sie zur Option Alle löschen im Wiedergabe-Menü. 1.
FILM-MODUS Aufnahme von Videoclips Bei der Videofunktion können Sie kurze Videosequenzen mit einer Auflösung von 320 x 240 Pixeln aufnehmen. 1. Öffnen Sie den Objektivschutz und drehen Sie den Modus-Schalter auf . Schalten Sie dann die Kamera ein. Auf dem LCD-Monitor wird die mögliche Aufnahmedauer angezeigt.
Wiedergabe von Videoclips Wenn Sie sich einen gespeicherten Videoclip ansehen möchten, gehen Sie so vor: 1. Drehen Sie den Modus-Schalter auf und schalten Sie die Kamera ein. 2. Mit den Tasten wählen Sie den Videoclip aus, den Sie sich ansehen möchten. 3.
ÜBERTRAGUNG DER AUFNAHMEN AUF DEN COMPUTER Schauen Sie sich Ihre Bilder/Videoclips zusammen mit Ihrer Familie an, versenden Sie sie als E-Mail oder stellen Sie sie ins Internet. Zuvor müssen Sie jedoch die Kamera mit einem USB-Kabel mit einem Computer verbinden und die Fotos/Videoclips auf den Computer übertragen.
Schritt 1: Installation des USB-Treibers bei Windows Der auf der CD-ROM mitgelieferte USB-Treiber ist nur für Windows 98 vorgesehen. Bei Windows 2000/ME/XP ist keine Treiberinstallation notwendig. 1. Legen Sie die mit der Kamera mitgelieferte CD-ROM in das CD-ROM-Laufwerk ein. Das Installation des USB-Treibers bei Macintosh Willkommen-Fenster erscheint.
Schritt 3: Laden Sie die Fotos/Video-Clips herunter. Bei Computern, die mit Windows arbeiten Wenn die Kamera eingeschaltet und mit dem Computer verbunden ist, wird sie wie ein Laufwerk behandelt. Sie können die Fotos/Videoclips herunterladen, indem Sie sie vom "austauschbaren Datenträger" (bei Macintosh “Unbenannt”) auf die Festplatte oder ein anderes Speichermedium kopieren.
INSTALLATION VON MGI PHOTOSUITE MGI PhotoSuite ist einn sehr benutzerfreundliches Bildbearbeitungsprogramm. Mit PhotoSuite können Sie die Bilder ganz einfach retouchieren, neu zusammenstellen und sortieren. Dieses Programm enthält eine Reihe von Schablonen für Bilderrahmen, Geburtstagskarten, Kalender und vieles mehr. Machen Sie Ihre Aufnahmen und probieren Sie dieses erstaunliche Programm aus.
INSTALLATION VON MGI PHOTOVISTA MGI PhotoVista ist ein benutzerfreundliches Programm, mit dem Sie im Handumdrehen spektakuläre 360°-Panoramabilder erstellen. Wenn Sie sich diese Panoramas ansehen, haben Sie das Gefühl, in eine absolut realistische Welt einzutauchen. PhotoVista fügt schnell und automatisch die Bilder zusammen, und mit der bedienungsfreundlichen Benutzeroberfläche können selbst Neulinge innerhalb weniger Minuten großartige Ergebnisse erzeugen.
MENÜ-OPTIONEN Aufnahme-Menü Bildgrösse Im Aufnahme-Menü können Sie eine Bildgröße, Bildqualität und die ISO- Empfindlichkeit einstellen. Ebenso können Sie hier die Belichtung, den Weißabgleich oder die LCD-Helligkeit einstellen. Aktivieren Sie hier auch den digitalen Zoom oder die Vorschau-Funktion. Um das Aufnahme-Menü zu öffnen, drehen Sie den Modus- Schalter auf und drücken dann auf die Taste .
Weissabgl. Der Weißabgleich wird für jede Aufnahme von der Kamera automatisch eingestellt. Die Aufnahmen fallen aber bei unterschiedlichen Lichtbedingungen (Tageslicht, bewölkter Himmel, Sonnenuntergang, Glühlicht, Neonlicht) immer anders aus. Die Kamera kann nicht wie das menschliche Auge die verschiedenen Lichtarten unterscheiden und sich entsprechend anpassen (Lichttemperaturen). Bei bestimmten Lichtverhältnissen können auf den Aufnahmen ungewollte Schattenbildungen auftreten.
Vorschau LCD helligkeit Wenn Sie die Vorschau-Funktion aktiviert haben, können Sie sich ein Bild gleich nach der Aufnahme als Vorschau ansehen. Nach der kurzen Vorschau kehrt die Kamera automatisch wieder in den -Modus zurück. Um die Vorschau zu aktivieren, müssen Film-Menü...
Wiedergabe-Menü Löschschutz Im Wiedergabe-Menü können Sie mit der Kamera eine Diaschau präsentieren oder die Bilder vom internen Speicher auf eine Speicherkarte laden. Hier können Sie die Bilder auch mit einem Löschschutz versehen und einzeln oder insgesamt löschen und die LCD-Helligkeit einstellen. Um das Wiedergabe-Menü zu öffnen, drehen Sie den Modus-Schalter auf und drücken dann auf die Taste .
Setup-Menü Formatieren Sie können die Kameraeinstellungen im SET-UP-Modus auswählen. Stellen Sie den Modus-Schalter auf SET-UP, und wählen Sie mit Hilfe der Taste eine Option aus. Mit dieser Funktion wird der interne Speicher (oder d i e S p e i c h e r k a r t e ) f o r m a t i e r t u n d a l l e Signalton gespeicherten Daten gelöscht.
Standard laden Wenn alle Kameraeinstellungen auf die ursprünglichen Standardwerte zurückgesetzt werden sollen, wählen Sie diese Option. Drücken Sie dann auf die Taste . Wählen die Option [Ja], und drücken Sie dann auf OK. Sie mit der Taste In der nachfolgenden Tabelle finden Sie für jedes Merkmal die Standardeinstellung. Merkmal Beschreibung Bildgröße...
Datendruck Videoausgang Wenn diese Funktion eingestellt ist, werden die Bilder mit dem Aufnahmedatum angezeigt. Um diese Funktion zu aktivieren, drücken Sie zunächst auf . Wählen Sie die Option [Ja], und drücken Sie dann auf OK. mit der Taste Sie können sich die Bilder auch auf einem TV-Bildschirm ansehen. Wählen Sie den geeigneten Videoausgang.