Controls And Functions - Audison Millennium Power 5 Bedienungsanleitung

CONTROLS AND FUNCTIONS

INDICATOR LIGHTS
ON
Lit when the amplifier is on.
SAFE
When lit, it indicates the intervention of protection circuits: in case of
overheating (temperature exceeding 80°C/176°F) or output anomalies
(presence of continuous current, short circuit or dangerously low load
impedance). When protection circuits intervene, the amplifier shuts down. Turn
the amplifier off. When the problem is corrected, turn the amplifier back on.
1
MODE
FREQUENCY CONTROLS
F/R F1 F2
Front/Rear Lo pass cut- Hi pass cut-
In this off frequency off frequency
configuration, of SUB of FRONT
the amplifier channel. channels.
allows the (50Hz-150Hz (50Hz-150Hz
realisation of 24dB/Oct.) 12 dB/Oct.)
a Hi Pass
FRONT + Hi
Pass REAR +
SUB system.
MULTICH. F1 F2
Multichannel Lo pass cut- Hi pass cut-
In this off frequency off frequency
configuratio, of SUB of WOOFER
the amplifier channel. channels.
allows the (50Hz-150Hz (50Hz-150Hz
realisation of 24dB/Oct.) 12dB/Oct.)
a two -way
FRONT +
SUB system.
CONTROLS
V1 - V2 - V3
Level adjustments for SUB,
FRONT/WOOFER and
REAR/MID-TW channels
(channels vary according
to the MODE switch
configuration).
1
AUXILIARY
OUTPUT/INPUT
F3 F4 IN REAR
Hi pass cut- N o t Input used to
off frequency active. drive REAR
of REAR channels.
channels.
(50Hz-150Hz
12dB/Oct.)
F3 F4 OUT MID-TW
N o t Lo pass cut- H i - p a s s
active. off frequency p r e a m p l i f i e d
for WOOFER output of MID-
channels, and TW filter for a
Hi-pass for supplementary
M I D - T W amplifier.
channels. Signal level:
(150Hz-850Hz 0 dB.
12dB/Oct.)
10
LEVEL
MODE
F/R
Front/Rear
In this
c o n f i g u r a t i o n ,
the amplifier
allows the
realisation of a
Hi Pass FRONT +
Hi Pass REAR +
SUB system.
MULTICH.
Multichannel
In this
c o n f i g u r a t i o n ,
the amplifier
allows the
realisation of a
two-way FRONT
+ SUB system.
1
GENERAL
INPUT
IN FRONT
General input
to drive SUB
and FRONT Hi
Pass channels.
IN FRONT
General input to
drive SUB, IN
WOOFER and Turn on control for the
M I D - T W
amplifier coming from radio-
channels.
cassette player (or from any
sources provided with remote
control for amplifiers).
Applied voltage must be
between 7 and 15 VDC.
CONFIGURATION OF CONNECTING CLAMPS
OUTPUT CLAMPS
SUB FRONT
Power output for
Left and Right power outputs for
SUB channels. It is
FRONT channels. They are Hi Pass
Lo Pass filtered, in a
filtered, in a range of frequencies
range of frequencies
between 50Hz and 150Hz
between 50Hz and
(12dB/Oct.), adjustable through
150Hz (24dB/Oct.),
F2. The available signal is
adjustable through
STEREO. (Bridge configuration is
F1. The available
not possible).
signal is MONO.
(Mix L + R).
WOOFER
Left and Right power outputs for
SUB
WOOFER channels. They are Hi
Power output for
Pass filtered, in a range of
SUB channels. It is
frequencies between 50Hz and
Lo Pass filtered, in a
150Hz (12dB/Oct.), adjustable
range of frequencies
through F2,and Lo Pass filtered, in
between 50Hz and
a range of frequencies between
150Hz(24dB/Oct.),
150Hz and 850Hz (12dB/Oct.),
adjustable through
adjustable through F4. The
F1. The available
available signal is STEREO. (Bridge
signal is MONO.
configuration is not possible).
(Mix L + R).
REMOTE
OUT
Output leading to other
amplifiers of the sound
system. It has to be
connected to the REMOTE
IN of the following amplifier
to allow the simultaneous
turning on of the whole
system. Available voltage
equal to REMOTE IN.
11
REAR
Left and Right power
outputs for REAR channels.
They are Hi Pass filtered, in
a range of frequencies
between 50Hz and
150Hz (12dB/Oct.),
adjustable through F3. The
available signal is STEREO.
(Bridge configuration is not
possible).
MID-TW
Left and Right power outputs
for MID-TW channels. They
are Hi Pass filtered, in a
range of frequencies
between 150Hz and
850Hz (12dB/Oct.),
adjustable through F4. The
available signal is STEREO.
(Bridge configuration is not
possible).
SUB VOL. POWER SUPPLY
CONTROL CLAMPS
VCR01 POWER
C o n n e c t i o n Input clamps for the
clamps for amplifier power supply.
the remote Connect the battery
v o l u m e positive and negative
c o n t r o l , according to indicated
V C R 0 1 polarities.
(optional). Applied voltage must be
between 11 and 15 VDC.