JB Systems Light iMove 7S Bedienungsanleitung Seite 6

ENGLISH
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color Mode
Normal: only full colors can be selected.
Split colors: you can select full colors and 2 colors that are next to each other on the color wheel.
 Press the MENU button unitl
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Dimmer Inversion
fader closed ( DMX value 000 )  full light output
Standard dimming:
fader open ( DMX value 255 )  blackout
fader closed ( DMX value 000 )  blackout
Inversed dimming:
fader open ( DMX value 255 )  full light output
 Press the MENU button up to when the
 Press the ENTER button so the display starts blinking.
 Use DOWN and UP buttons to select the
 Once the mode has been selected, press the ENTER button to save it. ( or automatically return to the
main functions without any change after 8 seconds )
To go back to the functions without any change press the MENU button again.
JB SYSTEMS®
OPERATION MANUAL
(no blackout) mode.
(split color) mode.
(pan inversion) mode.
(tilt inversion) mode.
is shown on the display.
(normal) or (dimmer inversion) mode.
7/62 iMove 7S
ENGLISH
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button untill
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
stored after 8 seconds. Or press the ENTER button again return to the mode
 To go back to the functions press the MENU button.
Focus Adjust
Used to help you adjusting the focus of the light beam and gobos.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button so the unit goes to the "tilt 90°" position.
 Press the ENTER button so the unit goes to the "pan 0°" position.
 Press the ENTER button so the unit goes to the "pan 90°" position.
 Press the ENTER button so the unit goes to the "pan 180°" position.
 Press the ENTER button so the unit goes to the "pan 270°" position.
In the Previous 5 steps you are able to adjust the focus with the UP/DOWN buttons on the unit (the display
shows the current focus status).
Attention: please note that you can only set an "average focus" for all 5 positions, so it is not possible to set
the focus perfectly sharp for all directions.
 To go back to the functions press the MENU button.
Self-Test
Used to activate the internal "self-test" program which shows all possibilities of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button to start the internal self-test program.
 To go back to the functions press the MENU button.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button.
Reset
Used to force a reset of the unit.
 Press the MENU button untill
is blinking on the display.
 Press the ENTER to reset all channels to their standard position.
 To go back to the functions press the MENU button.
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.
JB SYSTEMS®
OPERATION MANUAL
.
(display off when not used).
(display inversion), the option will be automatically
(normal display).
8/62 iMove 7S