Megaman LT0132 Bedienungsanleitung

SPECIFICATION
Item Number :
MM5400x
:
Model Number LT0118
Length :
1212mm
Voltage :
220-240V~
:
Frequency
50/60Hz
:
Rated Current 110mA
:
Wattage
18W
CAUTIONS
·Read the entire manual carefully before installation and operation.
·It is recommended that the installation be performed by a licensed and qualified electrician.
·Switch off the power source before installation or replacement.
·Before replacement of lamp, turn off and allow the lamp to cool down. Heat-resistant gloves are mandatory when handling the tube.
· To replace the fluorescent T8 tube ,the existing starter has to be removed together with the tube.A MEGAMAN® starter is provided to work with MEGAMAN® LED T
·MEGAMAN® LED T
8 Tube cannot work with electronic ballast.
·The minimum safety distance from the illuminated object is 0.1m
·Any constructive change of the luminaire in case of applying retrofit LED lamp shall not be permitted.
·In case of discrepancy in the weight of the lamp that you intend to replace, it is recommended to check the maximum loading of the luminaire before installation to avoid any
unstable mechanical function caused to the luminarie.
·The manufacture accepts no liability for any damages resulting from the misuse of the lamp or when it is used with inappropriate equipment.
·Consult your dealer for any enquiries about this product.
·This lamp is not suitable to be used in emergency luminaires designed for double-copped fluorescent lamp(s).
ATTENTION
·Instant restart is allowed.
·The LED T8 Tube is designed for indoor application.
·Declared operating temperature range is -30° C to +40° C.
·The overall energy efficiency and light distribution of any installation that uses such lamps are determined by the design of the installation.
PARTS LIST
LED tube x1 MEGAMAN® Starter x1
INSTALLATION
Step 1: Switch off the power source
Step 4: Remove the existing starter
2
Step 6: Install MEGAMAN® LED T8 Tube into the lamp holder
Step 7: Secure the lamp by turning 90
WIRING DIAGRAM
If magnetic ballast and starter are not available, an alternative wiring
method is shown below:
L
N
MEGAMAN®
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device,please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental safe recycling.
IDV GmbH
Birkenweiherstr. 2
D-63505 Langenselbold
Germany
www.megaman.de
LED Tube T8
MM5410x MM5403x
LT0132 LT0225
1212mm 1513mm
220-240V~ 220-240V~
50/60Hz 50/60Hz
170mA 155mA
32W 25W
0.1
---------
1
°
。
90
Existing magnetic ballast
L
N
MEGAMAN® LED T8 Tube
LED T8 tube
MM5403x MM5413x MM5404x
LT0225CS LT0242 LT0316
1513mm 1513mm 602mm
220-240V~
220-240V~ 220-240V~
50/60Hz 50/60Hz 50/60Hz
155mA 240mA 95mA
25W 42W 16W
m
Step 2 & 3: Remove the conventional lamp by turning 90
90
Step 5: Plug the MEGAMAN® starter into the starter holder.
Only MEGAMAN® starter can be used.
Step 8: Switch on the power source
Step 9. After the installation, it is recommended that there is an indicator for
identifying a MEGAMAN® LED T8 Tube is installed to prevent mixing up during
future maintenance.
MEGAMAN® starter
WARNING!
Risk of fire or electric shock. If magnetic ballast and starter are not available,
the LED T8 tube cannot wire as below method:
L
N
LT0118,
LT0225,
LT0242,
°
。
1
2
indicator
MEGAMAN® LED T8 tube
8010LT005C
LT0132,
LT225CS,
LT0316
8
Tube.
GB