Chicago Pneumatic CP7759 Betriebsanleitung Seite 3

EN
English
INSTRUCTION MANUAL
Machine Type:
This product is designed for installing and removing threaded
fasteners in wood, metal and plastic. - No other use is permitted.
For professional use only.
Air Supply Requirements
1. Supply tool with 90 psig (6.2 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes shown
in the diagram below.
Lubrication
1. Use an air line lubricator with SAE #10 oil, adjusted to two(2)
drops per minute. If an air line lubricator cannot be used, add
air motor oil to the inlet once a day.
2. Use 2 oz. (52 ml) of CP Pneu-Lube Synthetic Clutch Grease
8940158455.
Operation
The intended use of this impact wrench is with impact rated
sockets operating upon threaded fasteners. To operate, pull
trigger on handle. To operate in forward rotation, push the
reverse switch to the left. To operate in reverse rotation, push
the reverse switch to the right. This impact wrench includes
a power management system to enable adjustment of output
power in the forward direction. To adjust the power, rotate the
power regulator to #3 for maximum power, to #1 for minimum
power.
Maintenance
1. After first year, disassemble and inspect air motor and
impacting clutch every three (3) months if the tool is used every
day. Replace damaged or worn parts.
2. High wear parts are underlined in the parts list.
3. To keep downtime to a minimum, the following service kits are
recommended:
Tune-Up Kit: 8940168447
Technical Data
1/2" (12.7mm) Sq. Dr. Std.
Air Pressure 90 psi (6.2 bar)
Free speed; 8000 RPM
Original Instructions
Copyright 2010, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents
or part thereof is prohibited. This applies in particular to trademarks,
model denominations, part numbers and drawings. Use only
authorized parts. Any damage or malfunction caused by the use of
unauthorized parts is not covered by Warranty or Product Liability.
Noise & Vibration Declaration*
Sound pressure level, uncertainty 3 dB(A), in accordance with EN
ISO 15744. For sound power, add 11 dB(A).
Impacting sound level dB(A)
Pressure
CP7759
95
CP7759-2
CP7759Q
93
CP7759Q-2
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the
latest information please visit cp.com.
These declared values were obtained by laboratory type testing
in accordance with the stated standards and are suitable for
comparison with the declared values of other tools tested in
accordance with the same standards. These declared values are
not adequate for use in risk assessments and values measured in
individual work places may be higher. The actual exposure values
and risk of harm experienced by an individual user are unique
and depend upon the way the user works, the workpiece and
the workstation design, as well upon the exposure time and the
physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of values
reflecting the actual exposure, in an individual risk assessment in a
work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is
not adequately managed. An EU guide to managing hand-arm
vibration can be found at http://www.humanvibration.com/EU/
VIBGUIDE.htm
We recommend a programme of health surveillance to detect early
symptoms which may relate to noise or vibration exposure, so that
management procedures can be modified to help prevent future
impairment.
MANUFACTURER'S LIMITED WARRANTY
Limited Warranty: The "Products" of the Chicago Pneumatic Tool
Co. LLC ("CP") are warranted to be free from defects in material and
workmanship for one year from the date of purchase. This Warranty
applies only to Products purchased new from CP or its authorized dealers.
Of course, this Warranty does not apply to products which have been
abused, misused, modified, or repaired by someone other than CP or its
Authorized Service Representatives. If a CP Product proves defective in
material or workmanship within one year after purchase, return it to any
CP Factory Service Center or Authorized Service Center for CP tools,
transportation prepaid, enclosing your name and address, adequate
proof of date of purchase, and a short description of the defect. CP will,
at its option, repair or replace defective Products free of charge. Repairs
or replacements are warranted as described above for the remainder of
the original warranty period. CP's sole liability and your exclusive remedy
under this Warranty is limited to repair or replacement of the defective
Product. (There Are No Other Warranties Expressed Or Implied And
CP Shall Not Be Liable For Incidental, Consequential, Or Special
Damages, Or Any Other Damages, Costs Or Expenses Excepting
Only The Cost Or Expense Of Repair Or Replacement As Described
Above.)
CP7759 Series
Impact Wrench
Vibration level
ISO 15744 ISO 28927-2
Power
106
104
m/s
2
a=9.4m/s 2
k=2.3m/s 2
2
a=8.6m/s
2
k=1.4m/s