MaxPro MPBMS210 Anleitung Seite 10

Press the main switch (3) to turn on the saw.
Important. Place the material for sawing firmly on the machine surface, to prevent it from moving during
the sawing process.
After switching on the saw, wait for the blade (5) to reach its maximum speed.
Press the release lever (1) sideways and, using the handle (2), apply steady and light downward pressure
to move the machine head through the workpiece.
When the cut is completed, return the machine to its top parking position and let go of the On/Off switch.
Caution! A return spring causes the machine head to rise automatically at the end of the cut. Do not let
go of the handle (2) as soon as the cut is completed but steady the machine head and allow it to rise
slowly.
6.2 90° cross-cuts and 0°-45° rotary table (Fig. 10)
The crosscut saw can be used to make right and left angular cuts of 0°- 45° in relation to the stop rail.
Lift the machine head (4) to its top position.
Release the turntable (8) by slackening the locking grip (10).
Using the handle (2), set the turntable (8) to the desired angle, i.e. the marking on the turntable must
coincide with the desired angular setting (17) on the stationary base plate (9).
Re-tighten the locking handle (10) in order to fix the rotary table (8) in position.
Make the cut as described in Section 6.1).
6.3 Mitre cuts 0°-45° and rotary table 0° (Fig. 8/11)
The crosscut saw can be used to make miter cuts of 0° - 45° in relation to the work face.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left until the
pointer (11) coincides with the required angle value (15).
Re-tighten the locking nut (12) and make the cut as described in Section 6.1).
6.4 Mitre cuts 0°-45° and rotary table 0°-45° (Fig. 8/13)
The crosscut saw can be used to make miter cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° in relation to the stop rail (double miter cut).
Lift the machine head (4) to its top position.
Release the turntable (8) by slackening the locking grip (10).
Adjust the rotary table (8) by its handle (2) to the required angle (see also Section 6.2).
Retighten the tightening screw (10) in order to secure the turntable in place.
Undo the tightening screw (12) and use the handle (2) to tilt the machine head (4) to the left until it
coincides with the required angle value (in this connection see also section
Screw the tightening screw (12) back down again.
6.5 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (14) for sawdust and chips.
The debris bag (14) can be emptied by means of a zipper at the bottom.
6.6 Replacing the saw blade (Fig. 1-6)
Before changing the saw blade: Remove the power plug!
Wear work gloves to prevent injury whenchanging the saw blade.
Swing the machine head upwards (4).
Undo the screw (z) on the cover plate (f) of the saw blade.
Pull back the adjustable blade guard (6) and at the same time turn the cover plate to achieve access to
the flange bolt.
Press the saw shaft lock (13) with one hand while positioning the Allen key (d) on the flange bolt (31)
with the other hand. The saw shaft lock (13) engages after no more than one rotation.
Now, using a little more force, slacken the flange screw (31) in the clockwise direction.
Turn the flange screw (31) right out and remove the external flange (32).
Take the blade (5) off the inner flange and pull out downwards.
M M itre Saw MPBMS210 User Manual
10