Installation; Operation - SLV 470671 Betriebsanleitung

ENGLISH
OPERATING MANUAL FOR
COLOR CONTROL 470671 / 470672
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
 Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
 The product may not be modified or converted.
 In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be used with a suitable power supply unit, output voltage: 12V/DC or
24V/DC (e.g. SLV art.-no. 470548).
 only be installed according to safety class III (three).
 only be used in dry condition,
 not in damp or dirt-endangered rooms.
 not in areas of high air humidity.
 not be exposed to strong mechanical loads or to strong contamination.
INTEGRATION INTO THE COLOR CONTROL SYSTEM
Please read the system manual – www.slv.com/colorcontrolmanual.pdf

OPERATION

Please read the operating manual – www.slv.com/colorcontrolmanual.pdf
STORAGE AND DISPOSAL
Storage
 The product must be stored in a dry and clean environment. Do not
strain the product mechanically during storage.
After a damp or soiling storage the product may only be installed
after checking its condition by an approved electrician.
Disposal (European Union)
 Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2003/108) on electrical and electronic devices at local collection points for
such devices!

INSTALLATION

Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Unpacking
 Carefully take the product out of the packaging removing any transport
safeguards.
 Before disposal of the packaging material make sure that all components of
the product are removed.
 Electrical Connection
 Prepare the power supply. Use only a suitable power supply unit, output
voltage: 12V/DC constant or 24V/DC constant (e.g. SLV art.-no.
470548).
 RGB and RGBW products with an operation voltage of 12VDC or 24VDC may
be connected.
 Note that the voltage of the LED illumination is the same as the voltage of the
power supply of the controller.
 Note that the wattage of the connected LED illumination does not exceed the
wattage of the controller or the power supply.
 Establish the installation according to the installation diagram.
Hereby, SLV GmbH declares that the radio equipment described here is in
compliance with Directive 1999/5/EC. The full text of the EU declaration of
.
conformity is available at the following internet address:
www.slv.com/jump/470671
www.slv.com/jump/470672
This radio equipment may be distributed in all countries of the EU.
art.-no. 470671 / 470672 © 13.11.2015 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
12V/DC
15m
24V/DC
max.
FHSS
2.4GHz
7dBm
max.
W
433.92
W
ALL
MODE SPEED
MHz ZONE
1 2 3
9dBm
ZONE ZONE ZONE
A L L
M O D E SP EED
Z O N E
WHITE WHITE
max.
1 2 3
Z O N E ZO N E Z O N E ONLY OFF
W HI T E W HI T E
O N LY O FF
-
+
12VDC
24VDC
-
+
2x 1,5V
LR03
(AAA)
+
-
B
R
G
W
+
12V: 4x 18W
24V: 4x 36W