Commissioning The Device - Clatronic WSU 7026 RC Bedienungsanleitung

Outdoor Sensor (without Illustration)
Operating buttons in the battery compartment
• CH button
• C / F button
Display for temperature, air humidity (% RH) and channel

Commissioning the Device

Sensitive surfaces may be protected by plastic foil. Remove
this foil.
1) Inserting the Batteries (Batteries not Supplied)
1. Open the battery compartment lid on the back.
2. Match the polarities correctly (see the inside of the
battery compartment).
Outdoor sensor:
Insert 2 1,5 V, Type R6 / AA batteries.
Weather station:
Insert 3 1,5 V, Type R6 / AA batteries.
3. Close the battery compartment.
WARNING:
The batteries shall not be exposed to excessive
heat such as sunshine, fire or the like. Danger of
explosion!
CAUTION:
• Batteries can leak battery acid. If the device is out of
use for a long period of time, remove the batteries.
• Different battery types or new and used batteries
must not be used together.
• Batteries are not to be disposed of together with
domestic wastes. Dispose of the used batteries at
the relevant collection bin or at your dealer's.
NOTE:
A battery symbol in the display indicates that the bat­
teries need to be replaced.
2) Adjust Altitude Meter
After you have inserted the batteries, the altitude meter
indicator (M) will begin flashing.
1. Use the UP / DOWN buttons to adjust the altitude
of your location. By holding down the UP or DOWN
button, you activate the quick­scroll.
2. The appliance will wait approximate 30 seconds
following input before it switches to the search mode
for the outdoor sensor.
Please consult the internet for the correct information for
the altitude meter for your location.
You can also change this setting later. To do this, follow
the steps below:
1. Hold the HISTORY button down for approximately
2 seconds. The air humidity unit will begin flashing.
20
WSU7026RC_IM_CTC
2. Press the HISTORY button down briefly, the altitude
meter (M) will flash.
3. Adjust the setting using the UP / DOWN button. Con­
firm your entry with the HISTORY button.
3) Setting the Clock
Automatic
The appliance will now spend several minutes searching
for the current time data from transmitter DCF 77.
Symbol Meaning
flashing No radio signal available
Radio signal available, search for
flashing
current time in progress
Radio settings completed suc­
lights up
cessfully
NOTE:
• You can make the device search again for a station
signal at any time. To do this, keep the DOWN
button depressed, the symbol for the radio signal
will begin flashing again. You can also deactivate
the automatic search with the DOWN button. For
this, press the DOWN button during the radio signal
search. The symbol for the radio signal goes out.
• The signal can be received without problems within
a radius of approx. 2000 km around Frankfurt / Main,
but interference may occur, depending on local
conditions. This may occur especially in buildings
containing a high percentage of metal, as well as in
proximity to TV sets, PCs, mobile phones etc. which
are switched on! If the reception cannot be auto­
matically adjusted after 10 minutes in spite of the
alignment of the integrated antenna, the reception
in the respective location is too weak. In this case,
set the time manually or change location.
Manual
The time cannot be set manually whilst the device is
searching for a radio signal.
• In each case, confirm the input with the SET button.
The current indication to be set flashes on the display.
1. Hold the SET button down for approximately 3 sec­
onds until the display of the seconds flashes in the
display.
2. Now, you can use the UP and DOWN buttons to
adjust the settings for the seconds, the hours, the
minutes, the display format for the date (D / M or
M / D), the year (YEAR), the month (M), the day (D),
the language of the display for the weekday, the time
display format (24 H or 12 H ).
For the weekday language you can choose from the
following languages: GE = German, IT = Italian, FR =
French, NE = Dutch, ES = Spanish, DA = Danish,
EN = English.
05.03.18