indexa DVT40M Bedienungsanleitung Seite 11

!
Do not place the equipment and the batteries near fire, heat or in
areas of high temperature.
!
Protect the equipment and the cables against strong magnetic or
electrical fields and against strong mechanical loads and
vibrations.
!
Only use the equipment with the supplied original parts or original
accessories.
!
Before assembly and use check that all parts are included and that
they are undamaged.
!
Do not connect any damaged device (e.g. damage in transit).
Repairs to the equipment must only be performed by specialists.
!
Remove the mains adapter from the mains outlet when the device is
not required for a longer time.
!
This system transmits and receives radio-frequency signals. If the
system is not installed and used according to the instructions it may
cause interference with other apparatus and just as other apparatus
may interfere with the system. Interference can be reduced by
repositioning the system.
7. Positioning
Observe the following points:
!
The charging station must be placed on a solid and level surface,
ideally approx. 1-1.5 m above the ground and not directly next to a
wall (optimal reception).
!
Place the charging station in a central position in the dwelling, eg.
in the hallway. Make sure that the chime can be heard throughout
the dwelling.
!
Note that there must be a suitable power outlet within reach of
the mains adapter cable.
Wireless range
By free line of sight between a maximum wireless range of up to 100 -
150 m is possible, within buildings this is reduced to maybe 20 m.
The range cannot be guaranteed as it is dependent on the local conditions.
In order to avoid malfunctions, only one wireless system should be fitted for
each monitoring location/building/home.
A reduction of the range will be caused by:
#
Walls and Floors, in particular those of metal or with metal
reinforcement
#
Sheet metal surfaces e.g. refrigerator, metal shelves
#
Coated windows (eg. those with Insulating glass), radiators, and metal
surfaces
#
Strong electric fields and other radio equipment, eg. microwave ovens,
radio telephones, mobile phones, radio equipment in the 2.4 GHz
range, electric motors and power cables
#
Devices using the same or similar frequency (eg. WLAN-systems)
8. Connection
!
Connect the low voltage plug on the power supply unit [17]
provided to the power supply unit connection [13] on the charging
station [14].
!
Plug the power supply into a suitable power socket; the power
indicator [15] turns blue.
!
Open the battery compartment [11] on the mobile unit.
!
Insert the lithium battery provided with the terminals in the correct
position.
!
Close the battery compartment again.
!
Remove the protective film from the screen [6].
!
Place the mobile unit on the charging station. Charging of the
lithium battery begins automatically when the mobile unit is place
on the charger.
Note: Before using for the first time, allow the mobile unit to
charge up fully for 5 hours.
9. Pairing with the door intercom
The additional mobile unit and the door intercom DVT40T must be
paired in order to establish a radio connection.
To connect the additional mobile unit (max. 1 additional mobile unit) to
the door intercom, proceed as follows:
!
The door intercom must be connected to a power supply.
!
To switch on, press and hold the on/off button
unit until the start screen appears.
!
To change to the screen language of your choice:
!
—
press the left button
!
press the button [2] five times until the menu item
highlighted,
!
confirm with the left button
!
set the language by pressing buttons
English and
!
confirm again with the left button
!
—
Press the left button [3 - "Menu"] to open the menu.
!
Scroll through the menu with the
reach "Register" and press the left button
Channel no. 1 and no. 2 appear, the hash # indicates which
channel is currently selected.
!
Move the hash # to channel No. 2 by pressing [2]:
!
—
Press the left button
you now have approx. 20 seconds to complete pairing.
!
Press and hold the pairing button [28] on the door intercom until
you hear three short beeps on the intercom as confirmation that
pairing has been successful; the mobile unit then makes a "plop"
sound and the start screen appears again.
Note:
If the pairing was not successful, a short double tone can be heard and
the start screen reappears. In this case, position the door intercom
further away from the mobile unit if it was previously too close to the
mobile unit or position the door intercom to the monitor if it was too far
away from the mobile unit before.
[8] on the mobile
[3],
—
,
and [2] "0" for
—
["Select"].
and [2] buttons until you
—
[3 - "Select"].
[3 - " "]. The mobile unit beeps and
is
11