Fujitsu MCD3130SS Installationsanleitung

MCD3130SS
Magneto-Optical Disk Drive
Installation Guide
Installationsanleitung
Guide d'installation
© COPYRIGHT FUJITSU LIMITED
JAN. 1999 C156-E096-01XA
This guide is prepared to instruct the user on the switch and jumper
settings in the MCD3130SS when you install your MCD3130SS.
Note; Factory default settings are marked with .
Layout of PCA SCSI ID Setting
Table 1
SCSI ID SW1-01 SW1-02 SW1-03
Not
used 0 Off Off Off
1 Off Off On
GND
+5V 2 Off On Off
DC
3 Off On On
SCSI
4 On Off Off
Pin 50
5 On Off On
6 On On Off
7 On On On
SCSI
Pin 2
SW1 AND CNH2 SETTINGS
Switch 1 sets the SCSI ID and some drive functions and CNH2 sets
additional drive functions.
SW1
Key# Function Key on Key off
01
———— ————
02 SCSI ID (see table 1 above)
03
04 SCSI data bus parity check Enabled Disabled
05 Write cache mode Enabled Disabled
06 Device type mode MO Fixed Disk
07 Spindle automatic stop mode Enabled Disabled
08 Factory test (Not to be set by user) Enabled Disabled
CNH1 (TERMINATING POWER AND SCSI TERMINATION)
Terminal CNH1 uses shorting bars to set the power source and to
enable or disable SCSI termination.
Pin# Function Short Open Power supplied by 1–2 3–4
1–2 Power supplied by Supplied Not Drive Short Open
drive supplied
Host controller Open Short
3–4 Power supplied by Supplied Not
Drive and Host Short Short
host controller supplied
controller
5–6 SCSI termination Enabled Disabled
enabled
CNH2 (EXTERNAL SWITCH OPERATOR PANEL
SETTING)
1
TTL-IC
2
3
Pin# Function Open Short
4
— —
1 Cartridge-in detection
5
2 SCSI ID 4 — —
3 LED source (+5 V) — — 6
4 SCSI ID2 — —
7
5 LED source (–) — —
8
6 SCSI ID1 — —
9
7 Signal to eject cartridge — —
10
8 Ground — —
11
9 Device type mode Fixed disk MO
12
10 SCAM mode Disabled Enabled
11 Write verify mode Enabled Disabled 13
— —
12 Ground 14
13 Macintosh mode Disabled Enabled
15
14 SCSI type 0 SCSI 2 SCSI 1
16
15 Terminating resister mode Disabled Enabled
0V
— —
16 Ground
Note: The cable length must not exceed 30cm.
Device Driver
You need to install Fujitsu's device driver to avoid the 2KB sector
problem in Windows9x and the OS-timeout-problem in Windows9x and
NT3.51/4.0.
MCD3130SS HANDLING AND MAINTENANCE
Orientation Cleaning lens and media
The drive can be installed in one recommendation
of three orientations; either PCA Clean the lens on the drive head
up or on either side edge. and the disk media once every
three months. More frequent
Ejecting cartridge
cleaning may be required in a
Cartridges can be ejected by
dirty environment. Use the
pressing the eject key or by a
Fujitsu head cleaning kit and
SCSI eject command. Never
media cleaning kit. Head
eject a cartridge mechanically
Cleaning kits from other vendors
except in an emergency.
will not work.
WORLD WIDE WEB SITE
Corporate http://www.fujitsu.co.jp/ SINGAPORE http://www.fujitsu-computers.com.sg/
USA http://www.fcpa.com/ CANADA http://www.fujitsu.ca/
EUROPE http://www.fujitsu-europe.com/ AUSTRALIA http://www.fujitsu.com.au/