Herunterladen Diese Seite drucken

Werbung

B E D I E N U N G S A N L E I T U N G
www.conrad.de
Car Rave CRCS Autolautsprecher
CRCS 1024 II
Best.-Nr. 37 90 72
CRCS 1324 II
Best.-Nr. 37 90 74
CRCS 1624 II
Best.-Nr. 37 90 76
CRCS 2024 II
Best.-Nr. 37 90 78
Bestimmungsgemäße Verwendung
Die Autolautsprecher dienen zur Umwandlung der elektrischen Ausgangssignale von
Autoradios bzw. Autoverstärkern in hörbare Schallwellen und sind nur für den Anschluss an
Lautsprecherausgänge von solchen Geräten zugelassen.
Eine Verwendung ist nur im Kfz bzw. in geschlossenen Räumen, also nicht im Freien erlaubt.
Der Kontakt mit Feuchtigkeit, z.B. im Badezimmer u.ä. Räumen ist unbedingt zu vermeiden.
Eine andere Verwendung, als zuvor beschrieben, führt zur Beschädigung der Autolautsprecher
und ist überdies mit Gefahren, z.B. Kurzschluss, Brand etc. verbunden.
Das gesamte Produkt darf nicht geändert oder umgebaut werden!
Die Sicherheitshinweise sind unbedingt zu befolgen!
Sicherheitshinweise
Bei Schäden, die durch Nichtbeachten dieser Bedienungsanleitung verursacht
werden, erlischt der Garantieanspruch! Für Folgeschäden übernehmen wir
keine Haftung!
Bei Sach- oder Personenschäden, die durch unsachgemäße Handhabung oder
Nichtbeachten der Sicherheitshinweise verursacht werden, übernehmen wir
keine Haftung! In solchen Fällen erlischt jeder Garantieanspruch.
• Aus Sicherheitsgründen ist das eigenmächtige Umbauen und/oder Verändern des Produktes
nicht gestattet.
• Beim Anschluss der Autolautsprecher sind die Sicherheitshinweise des Gerätes, an das sie
angeschlossen werden ebenfalls zu beachten.
• Lagern Sie in der Nähe der Autolautsprecher keine Magnetspeicher, wie z.B. Disketten,
Videocassetten u.s.w., da das Magnetfeld der Lautsprecher die aufgezeichneten
Informationen dieser Speichermedien zerstören kann.
• Musik sollte nicht über einen längeren Zeitraum mit übermäßiger Lautstärke gehört werden.
Hierdurch kann das Gehör geschädigt werden.
• Eine zu hohe Lautstärke im Kfz-Innenraum hat zur Folge, dass akustische Warnsignale nicht
mehr wahrgenommen werden können; dadurch werden Sie und andere Verkehrsteilnehmer
gefährdet. Achten Sie deshalb auf eine angepasste Lautstärke.
• Unachtsamkeit im Straßenverkehr kann zu schwerwiegenden Unfällen führen. Eine
Bedienung der HiFi-Anlage darf deshalb immer nur dann erfolgen, wenn es die
Verkehrssituation erlaubt und Sie durch die Bedienung der Anlage nicht vom
Verkehrsgeschehen abgelenkt werden.
• Vermeiden Sie eine starke mechanische Beanspruchung der Autolautsprecher.
• Setzen Sie die Autolautsprecher keinen hohen Temperaturen, starken Vibrationen oder hoher
Feuchtigkeit aus.
• Lassen Sie das Verpackungsmaterial nicht achtlos liegen, Plastikfolien/-tüten, Styroporteile,
etc., könnten für Kinder zu einem gefährlichen Spielzeug werden.
• Sollten Sie sich über den korrekten Anschluss nicht im Klaren sein oder sollten sich Fragen
ergeben, die nicht im Laufe der Bedienungsanleitung abgeklärt werden, so setzen Sie sich
bitte mit unserer technischen Auskunft oder einem anderen Fachmann in Verbindung.
Montage
Änderungen am Fahrzeug, die durch den Einbau der Autolautsprecher oder
anderer Komponenten nötig sind, müssen immer so ausgeführt werden, dass
dadurch keine Beeinträchtigung der Verkehrssicherheit oder der konstrukti-
ven Stabilität des Kfz entstehen. Bei vielen Kfz erlischt bereits durch das
Aussägen eines Blechteils die Betriebserlaubnis.
Sollten Zweifel über die Auswahl des Einbauplatzes bestehen, informieren Sie
sich bitte bei Ihrem Kfz-Händler.
Vergewissern Sie sich vor der Ausführung von Befestigungsbohrungen, dass
hierdurch keine elektrischen Kabel, Bremsleitungen, der Kraftstofftank o.ä.
beschädigt werden.
Beachten Sie bei der Verwendung von Werkzeugen zum Einbau Ihrer Auto-
HiFi-Komponenten die Sicherheitshinweise der Werkzeughersteller.
Berücksichtigen Sie beim Einbau der Autolautsprecher bzw. Ihrer HiFi-Anlage
die Unfallgefahr, die von losgerissenen Geräten im Falle eines Unfalls ausge-
hen kann. Befestigen Sie deshalb jedes Teil sicher und an einem Platz an dem
es nicht zu einer Gefahr für die Insassen werden kann.
• Die Basslautsprecher sind für den Einbau in genormte Autolautsprecheröffnungen konzi-
piert.
• Stellen Sie sicher, dass der erforderliche Raum hinter der Montagefläche für die Einbautiefe
der Basslautsprecher ausreichend ist. Berücksichtigen Sie beim Türeinbau auch den Raum,
den ein geöffnetes Seitenfenster beansprucht.
• Die Montagefläche muss stabil genug sein um eine sichere Befestigung zu ermöglichen. Evtl.
kann sie auch durch ein Holzbrett o.ä. verstärkt werden.
• Montieren Sie die Lautsprecher mit dem beiliegenden Montagematerial.
Version 06/03
• Montieren Sie die Hochtöner gemäß folgender Abbildung in der Nähe der Basslautsprecher:
• Richten Sie die Hochtöner wunschgemäß aus.
Anschluss
Beachten Sie beim Anschluss der Autolautsprecher, dass die Anschlusskabel
nicht gequetscht oder durch scharfe Kanten beschädigt werden.
Ein Anschluss darf nur an geeignete Lautsprecherausgänge von Autoradios/-
verstärkern erfolgen.
Stellen Sie sicher, dass die in den technischen Daten angegebenen Werte für
Impedanz und Belastbarkeit mit den Daten des angeschlossenen Verstärkers
harmonieren. Ansonsten kann es zu Beschädigungen der Autolautsprecher
oder des Verstärkers kommen.
Das Gerät, an das die Autolautsprecher angeschlossen werden, muss wäh-
rend der Anschlussarbeiten ausgeschaltet sein.
• Verbinden Sie die Lautsprecherleitungen vom Autoradio bzw. Verstärker mit den
Steckzungen an den Lautsprechern:
großer Flachsteckverbinder > positiver Lautsprecheranschluss
kleiner Flachsteckverbinder > negativer Lautsprecheranschluss
• Verbinden Sie die Anschlussleitungen der Hochtöner mit den Flachsteckzungen der
Basslautsprecher:
schwarz/weiße Leitung
> große Flachsteckzunge
schwarze Leitung
> kleine Flachsteckzunge
Technische Daten
Modell
CRCS 1024-II
CRCS 1324-II
Impedanz
4 Ohm
4 Ohm
Belastbarkeit
(RMS/max.)
50/100W
50/100W
Frequenzbereich (Hz)
50-20.000
40-20.000
Schalldruck (dB/W/m) 88
89
Basslautsprecher
10cm
13cm
Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic GmbH,
Klaus-Conrad-Straße 1, D-92240 Hirschau.
Diese Bedienungsanleitung entspricht dem technischen Stand bei Druck-
legung. Änderung in Technik und Ausstattung vorbehalten.
© Copyright 2003 by Conrad Electronic GmbH. Printed in Germany.
O P E R A T I N G I N S T R U C T I O N S
Car Rave CRCS Car Loudspeakers
CRCS 1024 II
Item-No. 37 90 72
CRCS 1324 II
Item-No. 37 90 74
CRCS 1624 II
Item-No. 37 90 76
CRCS 2024 II
Item-No. 37 90 78
Prescribed Use
The car loudspeakers are designed to convert electrical output signals of car radios and/or car
audio amplifiers into audible sound waves and are only licensed for the connection to loud-
speaker outputs of such devices.
This product is only authorised for the use in a motor vehicle or indoors, not outdoors. Contact
with dampness e.g., in the bathroom or similar rooms is to be avoided by all means.
Any use other than the one described above damages the car loudspeakers and moreover it
involves dangers, such as e.g., short-circuit, fire, etc.
No part of the product may be modified or rebuilt.
Always observe the safety instructions.
Safety Instructions
In the case of any damages which are caused due to failure to observe these
operating instructions, the guarantee will expire. We do not assume liability
for resulting damages.
Nor do we assume liability for damage to property or personal injury, caused
be improper use or the failure to observe the safety instructions. The guaran-
tee will expire in any such case.
• The unauthorised rebuilding and/or modifying of the product is not permitted, because of
safety and approval reasons.
• When connecting the car loudspeakers, the safety notes of the device to which it is to be con-
nected must also be observed.
• Don't store magnetic memory such as floppy disks, video tapes etc. near the loudspeakers,
since the magnetic field of the loudspeaker can destroy the recorded information on these
memory mediums.
• You should not listen to music at excessive volume over a longer period of time. This can
damage the hearing.
• If the volume is too high inside the vehicle, acoustic warning signals cannot be heard, this is
a danger to you and other road users. This is why you should make sure that the volume is
at a reasonable level.
• Carelessness in traffic can lead to serious accidents. The hi-fi system should only be ope-
rated when the traffic situation permits it and you are not distracted from the traffic by ope-
rating it.
• Avoid strong mechanical use of the car loudspeakers.
• Don't expose the car loudspeakers to high temperatures, strong vibrations or high humidity.
• Do not expose the car loudspeaker to high temperatures, strong vibrations or high humidity.
• Do not leave packing material unattended. Plastic foils or bags, polystyrene parts, etc. could
become dangerous playing material for children.
• When in doubt about how to connect it correctly or should any questions arise that are not
answered in these operating instructions, contact our Technical Advisory Service or another
expert.
Installation
Changes on the vehicle which are necessary because of the installation of the
CRCS 1624-II
CRCS 2024-II
car loudspeakers or other components, will always have to be carried out in a
4 Ohm
4 Ohm
way so that traffic safety or the constructive stability of the vehicle is not
affected. For many vehicles the sawing out of a metal part means that the
70/150W
80/200W
operating license will expire.
30-20.000
25–20.000
If you are in doubt about the choice of the mounting place please get the nec-
90
91
essary information at a vehicle dealer.
Before you carry out the installation make sure that the fastening drillings that
16cm
20cm
may be necessary don't damage any electrical cables, brake air conduit, fuel
tank or similar.
When using tools for fastening your car hi-fi components, pay attention to the
safety notes of the tool manufacturer.
When installing the car loudspeakers and/or your hi-fi system, please pay
attention to the risks of accidents that can be caused by torn off devices. This
is why you should fasten each part securely and in a place where it cannot
become a danger to the passengers.
• The bass loudspeakers are designed for the installation into standardized car loudspeaker
openings.
• Make sure that the necessary space behind the installation area is sufficient for the installa-
tion depth of the bass loudspeaker. When installing it in the door, also take the room into
account that an opened side window takes up.
• The mounting area needs to be sufficiently stabile to allow a secure fixation. It might be pos-
sible to reinforce it with a wooden board.
• Mount the loudspeakers with the installation material included.
www.conrad.de
• Install the high-range horns in accordance with the illustration, near the bass loudspeaker:
Version 06/03
• Adjust the high-range horns to your liking.
Connection
When connecting the car loudspeakers, make sure that the connecting cables
are not crushed or damaged by sharp edges.
A connection may only be carried out to suitable loudspeaker outputs of car
radios/amplifiers.
Make sure that the values for impedance and current carrying capacity given
in the technical specifications harmonises with the specifications of the con-
nected amplifier. Otherwise the car loudspeakers or the amplifier might get
damaged.
The device to which the car loudspeakers are connected, has to be switched
off during connection.
• Connect the loudspeaker wires of the car radio or amplifier with the plug-in contact stud to
the loudspeakers:
large flat pin-and-socket connector >
small flat pin-and-socket connector >
• Connect the connecting wires of the high-range horns with the flat plug-in contact studs of
the bass loudspeakers:
black/white wire
>
black wire
>
Technical Specification
Model
CRCS 1024-II CRCS 1324-II CRCS 1624-II CRCS 2024-II
Impedance
4 Ohm
load capacity
(RMS/max.)
50/100W
Frequency range (Hz)
50-20.000
Sound pressure (dB/W/m) 88
Bass loudspeaker
10cm
These operating instructions are published by Conrad Electronic GmbH,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
The operating instructions reflect the current technical specifications at time
of print. We reserve the right to change the technical or physical specifications.
© Copyright 2003 by Conrad Electronic GmbH. Printed in Germany.
positive loudspeaker connection
negative loudspeaker connection
large plug-in contact stud
small plug-in contact stud
4 Ohm
4 Ohm
4 Ohm
50/100W
70/150W
80/200W
40-20.000
30-20.000
25–20.000
89
90
91
13cm
16cm
20cm

Werbung

loading

Inhaltszusammenfassung für Conrad CRCS 1324-II

  • Seite 1 We reserve the right to change the technical or physical specifications. • The mounting area needs to be sufficiently stabile to allow a secure fixation. It might be pos- © Copyright 2003 by Conrad Electronic GmbH. Printed in Germany. © Copyright 2003 by Conrad Electronic GmbH. Printed in Germany.
  • Seite 2 • De basluidsprekers zijn geschikt voor de inbouw in genormeerde openingen voor autoluid- chaîne Hi-fi des risques de blessure que pourraient causer des appareils mal Cette notice est une publication de la société Conrad Electronic GmbH, Deze gebruiksaanwijzing is een publicatie van Conrad Electronic GmbH, sprekers.
  • Seite 3 Einbau ∅ = 120 mm Gesamt ∅ = 155 mm Lochabstand = 138 mm Magnet ∅ = 70 mm 379074 Einbautiefe = 55 mm Gesamttiefe = 64 mm...

Diese Anleitung auch für:

Crcs 1024-iiCrcs 1624-iiCrcs 2024-ii