Care And Cleaning - Speaka Professional 1680331 Bedienungsanleitung

Operation
a) Connection diagram
• Connect all components according to the connection diagram in section b ("Connection diagram").
• Connect the power supply.
• Ensure that the infrared receiver (connected to "IR IN") is positioned so that it is within direct view of your
remote control.
• The infrared transmitter (connected to "IR OUT") must be positioned so that it can transmit signals to the
IR receiver without obstacles.
• Only connect or disconnect cables when there is no signal.
b) Connection diagram
DC
TX Transmitter
Use shielded cables for optimal transmission. Poor quality cables may impair transmission and
prevent the signal from being transmitted at the maximum cable length. An HDMI 4K@60 Hz
signal can only be transmitted over a length of less than 5 m.

Care and cleaning

• Always disconnect the product from the power supply before cleaning it.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
housing or stop the product from functioning properly.
• Use a dry, lint-free cloth to clean the product.
DC
RX Receiver
Disposal
Electronic devices are recyclable waste and must not be placed in household waste. At the end
of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to protection of the environment.
Technical data
a) Transmitter/receiver
Input voltage/current ............................. 5 V/DC, 1 A
Power consumption .............................. 2.5 W (transmitter), 3 W (receiver)
Material ................................................. Aluminium alloy
Colour ................................................... Black
Compatible remote controls .................. 20 to 60 kHz operating frequency
Transmission cable ............................... CAT6/6A/7
Range ................................................... Up to 60 m (4K, 30 Hz) and up to 30 m (4K, 60 Hz)
Transmission speed.............................. Max. 10.2 G/Bits
HDMI standard ..................................... HDMI2.0, compatible with HDCP2.2
Resolution ............................................. 480i@60 Hz, 480p@60 Hz, 576i@50 Hz, 576p@50 Hz,
720p@50/60 Hz,1080i@50/60 Hz, 1080p@50/60 Hz,
max. 4Kx2K 24/25/30/60/ Hz
Supported audio formats ...................... PCM
TMDS interface ..................................... 0.5 to 1.5 V p-p (input/output)
Digital down converter .......................... 5 Vp-p (TTL) (input/output)
Input cable ............................................ ≤8 m (AWG24)
Output cable ......................................... ≤8 m (AWG24)
ESD Protection ..................................... ±6 kV (contact)
±8 kV (air gap) according to IEC61000-4-2 standards
Mean time between
failures (MTBF) ..................................... > 3000 hours
Operating conditions ............................. 0 to +50 ºC, 0–90 % relative humidity (non-condensing)
Storage conditions ................................ -10 to +70 ºC, 0–90 % relative humidity (non-condensing)
Dimensions (L x W x H) ........................ 77.5 x 56.15 x 22.66 mm
Weight .................................................. 160 g
b) PSUs
Input voltage/current ............................. 100 - 240 V/AC, 50/60 Hz, 0.2 A
Output voltage / current ........................ 5 V/DC, 1.0 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1680331_v1_0618_02_DS_m_4L_(1)