Gemini PS-828EFX Bedienungshandbuch Seite 5

CONTROLS:
(CONTINUED)
13 CHANNEL ROTARY GAIN
The CHANNEL ROTARY GAIN allows you to boost the signal of each
individual channel depending on how low or high its input level is
14
3 BAND EQUALIZER
The 3 BAND EQUALIZER adjust the tone of each CHANNEL by giv-
ing you a choice 3 frequencies (BANDS) to adjust , from LOW,
MIDRANGE (MID) and HIGH's ,you can use the adjustment knobs to
higher or lower the 3 separate frequencies till the sound of the music
program is appropriate for your listening environment.
15 CHANNEL VOLUME FADER
After you have chosen which input you will use with the INPUT
SELECTOR the corresponding CHANNEL FADER will allow you to
adjust the volume for that particular CHANNEL.
16
CROSSFADER ASSIGNMENT/ADJUSTMENT SWITCHES
The fader assignment push button allows you to assign which two
channel faders will be controlled by the CROSSFADER in the UP po-
sition the CROSSFADER will fade between channels (1) and (2), in
the down or pushed in position the CROSSFADER will fade between
channels (3) and (4). The CURVE ADJUSTMENT selector lets you
choose between two fader CURVE settings, positioning the switch to
the right will give you a gradual CROSSFADE and positioning the
switch to the left will give you a quick CROSSFADE.
CROSS FADER
17
The CROSS FADER allows you to mix evenly from one source to an-
other. On the PS-828EFX The CROSSFADER is assignable between
either channels (1) and (2) or channels (3) and (4) depending on the
position of the fader assignment push button (see above).
The CROSS FADER on the PS-828EFX is also removable and if the
need arises can be replaced.The RG-45 (RAILGLIDE™)
DUAL-RAIL CROSS FADER, which has internal dual stainless steel
rails that allow the slider to ride smoothly and accurately from end to
end can be purchased from your local GEMINI dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE
FADER BACK AND FORTH. PRESSING DOWN ON THE
CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.
CHANNEL AND MASTER VU METERS
18
The PS-828EFX has a VU METER on each channel that allows you to
monitor the decibel levels of its input, you also have a master output
VU METER that lets you monitor the decibel levels of the LEFT and
RIGHT MASTER output.
CUE MASTER SWITCH
19
The VU METER has two display modes, in CUE mode it will display
the level of the channel you are cueing, in MASTER mode it displays
the main MASTER output.
20 MASTER VOLUME ROTARY
The MASTER VOLUME ROTARY knob adjust the volume of the
MAIN output.
21 CUE/PGM ROTARY
The CUE/PGM ROTARY determines the mix between the chosen
CHANNEL CUE SELECTOR and the MAIN OUTPUT mix.
22
CUE VOLUME ROTARY KNOB
The CUE VOLUME ROTARY KNOB adjusts your HEADPHONE
MONITOR OUTPUT'S volume.
CHANNEL CUE SELECTOR SWITCH
19 23
The CHANNEL CUE SELECTOR SWITCH allows you to choose
which channel you wish to monitor in your headphones by pressing
this switch on any channel you will be able to listen to that channels
input in your headphones multiple CHANNEL SWITCHES can be
pressed to monitor more than on input at a a time.
EFFECTS:
19 24
EFX CONTROLS
The PS-828EFX has three effects and any one effect can be chosen
by pressing its respective button, once an effect is chosen a red LED
light will illuminate indicating the effect is engaged you may then
change its parameters with the EFX PARAMETER jog wheel.
Each effect only engages momentarily then defaults back to (0)
effect, you can keep the effect from defaulting by pressing the HOLD
button located above the effects buttons, the HOLD button will hold
the effect indefinitely until you either disengage the button or engage
a new effect. The HOLD LED will illuminate when HOLD is engaged.
25
EFX PARAMETER JOG WHEEL
The EFX PARAMETER JOG WHEEL allows you to adjust either the
depth and speed of an effect like with the FLANGER and TRANS
or what the effect does like with the FILTER.
FILTER
With the FILTER the EFX PARAMETER JOG WHEEL controls how
much the filter will cut, for example if you spin the JOG WHEEL all
the way to the left the filter will cut off all the HIGH frequencies
leaving only the LOW'S, and if you spin it all the way to the right, the
filter will cut off all the LOW'S leaving just the HIGH end frequencies.
FLANGER
With the FLANGER the EFX PARAMETER WHEEL controls how
deep the flanger will sound. Turn the wheel either way just a little
and the FLANGER is barely audible, the more you turn the wheel in
either direction, the FLANGER will get deeper sounding and give
you the tunnel or jet plane sound effect.
TRANS
Or TRANSFORMER effect will turn the volume of the track off and
on fast or slow depending where the EFX PARAMETER WHEEL is,
giving you a TRANSFORMER sounding effect. Turn the wheel in
either direction just a little and the effect will cut the music volume up
and down slowly, keep turning the wheel in either direction and the
effect will cut the music volume up and down quickly, you can then
adjust the speed of the transfom effect to match the tempo of your
music.
26
EFFECTS ASSIGN
The PS-828EFX has an EFX SEND on each channel that allows you
to SEND that channels signal individually to the effect section of the
mixer, any combination of the four can be applied and all can send at
once.
PS-828EFX
5