Technical Data; Maintenance And Cleaning - Conrad 43 01 80 Bedienungsanleitung

b) Connecting transmitter and receiver
• Plug an RJ45 plug of a Cat 5e or Cat 6 cable into the HDBaseT socket of the transmitter and receiver.
c) Connecting IR transmitter/receiver
• Connect the infrared transmitter (IE) to the transmitter's circular connector (IR Emitter). Position the
infrared transmitter (IE) in such a way that it is placed in front of or close to the IR receiver of your HDMI
source, such a Blu-Ray player or SAT receiver.
• Connect the infrared receiver (IR) to the receiver's circular connector (IR Receiver). Position the infrared
receiver (IR) in such a way that it is within the transmitting range of the IR remote control used by you.
d) Connecting HDMI / Ethernet sources to the transmitter
• Connect an HDMI source (e.g. Blu-Ray player, SAT receiver) with an HDMI cable to the transmitter's HDMI
socket (HDMI IN).
• Connect network devices with an Ethernet cable to the RJ45 ports (Ethernet ports). Two network devices
can be connected.
e) Connecting HDMI / Ethernet output devices to the receiver
• Connect an HDMI output device (e.g. TV set) with an HDMI cable to the receiver's HDMI socket (HDMI
OUT).
• Connect network devices with an Ethernet cable to the RJ45 ports (Ethernet ports). Two network devices
can be connected.
f) Connecting power adaptors
• Connect one power adaptor each with the circular sockets (5 V/DC, 2A) to the transmitter and receiver.
Startup
• Connect all devices to the mains voltage. The Power LED lights up once you connect transmitter and
receiver to the mains voltage.
• The Active LED starts flashing once the transmitter and receiver have been started up.
• The Link LED lights up when the data connection between transmitter and receiver is active (this can
take a few seconds).
• The connected network devices are now connected via Ethernet.
• Start playback of the HDMI source (e.g. Blu-Ray player, SAT receiver) with the remote control of the HDMI
source, or directly on the device.
• The output is done via the HDMI output device (e.g. TV set). The HDCP LED lights up when a signal with
HDCP is being transmitted. The HDCP LED flashes when a signal without HDCP is being transmitted.

Maintenance and cleaning

• Before cleaning, disconnect the transmitter and receiver from the connected devices and unplug the power
adaptors from the mains outlets.
• There are no components located inside the product you need to maintain. Never open/dismantle the
product.
• Use a soft, anti-static and lint-free cloth.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

a) General information
Extension ....................................................via Cat5e or Cat6 cable, max. 100 m
Bandwidth per channel ...............................3.4 Gbps
Resolution ...................................................up to 1080p
Operating conditions ...................................0 to +50 °C, 10 – 85 % RH (non-condensing)
Storage conditions ......................................-10 to +80 °C, 5 – 90 % RH (non-condensing)
b) Transmitter (Sender)
Input............................................................1x HDMI; 2x RJ45
Output .........................................................1x RJ45
Current consumption ..................................max. 550 mA
Dimensions (W x H x D) .............................75 x 25 x 110 mm
Weight ........................................................212 g
c) Receiver
Input............................................................1x RJ45
Output .........................................................1x HDMI; 2x RJ45
Current consumption ..................................max. 1500 mA
Dimensions (W x H x D) .............................75 x 25 x 110 mm
Weight ........................................................218 g
d) Power adaptors
Input voltage / current .................................100 – 240 V/AC, 50/60 Hz, 0.35 A
Output voltage / current ..............................5 V/DC, 2000 mA
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
V1_0813_02-ETS_KV