Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
Do not reach into the input slot.
Do not insert any paper clips or other metallic objects into the input slot.
Persons with long hair must make sure to maintain sufficient distance from
the input slot.
Keep ties, scarfs, loose clothing and long necklaces or bracelets away from
the input slot.
Do not use any spray bottles/cans in the direct vicinity of the product.
Do not operate the product for longer than 2 minutes without interruption to
prevent the motor from overheating.
If the collection container is full before 2 minutes have elapsed, turn the
product off. Empty the collection container before continuing use.
Allow the product to rest for at least 40 minutes before continuing use.
a) Positioning and connection
• Place the product on a stable, even, nonslip surface.
• Make sure that the selection switch is in the middle position OFF.
• Connect the power plug to a common household power outlet.
b) Shredding paper
Insert a maximum of 6 pieces of paper (size DIN A4) with a maximum
grammage of 80 g/m
into the input slot at the same time.
2
Do not shred self-stick notes or paper with residual adhesives.
• Slide the selection switch to the left position AUTO.
• Now carefully insert the paper into the input slot. The paper is pulled in and
shredded automatically.
• When you are finished, slide the selection switch to the middle position OFF.
c) Shredding credit cards
Do not shred more than one credit card at the same time.
• Slide the selection switch to the left position AUTO.
• Now carefully insert a single credit card into the input slot. The credit card is pulled
in and shredded automatically.
• When you are finished, slide the selection switch to the middle position OFF.
d) Removing a paper jam
• Slide the selection switch to the right position REV.
• The shredding unit now runs in the opposite direction and pushes the jammed paper
back out.
• When you are finished, slide the selection switch to the middle position OFF.
Troubleshooting
Problem
Cause
The collection container
In AUTO mode, the
is full. Paper in the
shredding unit runs
shredding unit is not
without interruption.
drawn in.
Some bits of paper are
The bits of paper are
left in the shredding unit
stuck between the
after shredding.
blades.
The automatic paper feed
Some bits of paper are
is not working after the
blocking the automatic
shredding unit was run in
feed.
REV mode.
The paper was inserted
into the input slot at a
The automatic paper feed
slant.
stops even though there
is paper in the input slot.
The paper is too soft, too
thin, damp or crinkled.
The product is not
working even though
The motor is overheated.
there are no bits of paper
left in the shredding unit.
Maintenance and cleaning
• Unplug the device before cleaning.
• There are no components located inside the product you need to maintain. Never
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical
• To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much
• You can easily remove dust using a long-haired, soft and clean brush.
Disposal
Technical data
Operating voltage................................220 – 240 V/AC, 50 Hz
Power consumption............................190 W
Current consumption ..........................0.9 A
Feeding slots width .............................220 mm (paper)
Cutting width ........................................6 mm
Cutting speed .......................................3 m/min
Amount of sheets ................................max. 6 (at 80 g/m
Container volume ................................10 l
Operating time .....................................2 min ON / 40 min OFF
Noise level............................................<70 dB
Safety level...........................................1 (DIN 32757)
Cable length .........................................approx. 1.2 m
Operating conditions ..........................-10 to +55 ºC, 20 – 90 % RH
Storage conditions..............................-10 to +55 ºC, 20 – 90 % RH
Dimensions (W x H x D)......................280 x 330 x 140 mm
Weight ...................................................1.42 kg
Solution
Disconnect the power
plug from the power
outlet and empty the
collection container.
Slide the selection switch
to REV.
Insert the paper into the
input slot straightly.
Fold, dry or smoothen the
paper.
Allow the product to cool
down before continuing
use.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
open/dismantle the product.
solutions as they can cause damage to the housing and malfunctioning.
pressure to the housing as this may cause scratch marks.
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of
the environment.
55 mm (credit card)
)
2
V1_0215_02-ETS-Mkd
Werbung
Inhaltsverzeichnis
