Herunterladen Inhalt Inhalt
Teilen
Diese Seite drucken
  1. Anleitungen
  2. Marken
  3. EPIC Board Anleitungen
  4. Mainboards
  5. EPIC-9457
  6. Handbuch

EPIC Board EPIC-9457 Handbuch

Vorschau ausblenden
Inhaltsverzeichnis

Quicklinks

Diese Anleitung herunterladen
E P I C B o a r d
E P I C - 9 4 5 7
EPIC-9457
Intel® Atom™
N270 Processor
DDRII 400/533 Memory
Up to 24-bit Dual-channel LVDS LCD
6 USB 2.0 / 4 COMs / 1 EIDE/
2 SATAII/ 1 CompactFlash/ 1 Digital I/O
EPIC-9457 Manual Rev.A 1st Ed.
July 2009
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für EPIC Board EPIC-9457

  • Seite 1 E P I C - 9 4 5 7 EPIC-9457 Intel® Atom™ N270 Processor DDRII 400/533 Memory Up to 24-bit Dual-channel LVDS LCD 6 USB 2.0 / 4 COMs / 1 EIDE/ 2 SATAII/ 1 CompactFlash/ 1 Digital I/O EPIC-9457 Manual Rev.A 1st Ed. July 2009...
  • Seite 2 E P I C B o a r d E P I C - 9 4 5 7 Copyright Notice This document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
  • Seite 3 E P I C B o a r d E P I C - 9 4 5 7 Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™...

  • Seite 4: Packing List

    • 1709070500 SATA Cable • 1700060152 KB/Mouse Cable • 9657666600 Jumper Cap • Quick Installation Guide • Utility CD • EPIC-9457 w/Heatsink If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.

  • Seite 5: Inhaltsverzeichnis

    E P I C B o a r d E P I C - 9 4 5 7 Contents Chapter 1 General Information 1.1 Introduction ............1-2 1.2 Features ..............1-3 1.3 Specifications ............1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ..........2-2 2.2 Location of Connectors and Jumpers ......2-3 2.3 Mechanical Drawing ..........2-5 2.4 List of Jumpers ............2-7...
  • Seite 6 E P I C B o a r d E P I C - 9 4 5 7 2.18 24-bit LVDS Connector (CN4) .......2-13 2.19 Wide Voltage Power Connector (CN5)....2-14 2.20 Audio Connector (CN6) ........2-14 2.21 18-bit LVDS Connector (CN7) .......2-14 2.22 18-bit Inverter Power Connector (CN9) ....2-15 2.23 TV-out Connector (CN10)........2-15 2.24 USB Connector (CN11) ........2-15...
  • Seite 7 E P I C B o a r d E P I C - 9 4 5 7 A.1 Programming ............ A-2 Appendix B I/O Information B.1 I/O Address Map ..........B-2 B.2 1 MB Memory Address Map ......B-3 B.3 IRQ Mapping Chart ..........

  • Seite 8: Chapter 1 General Information

    E P I C B o a r d E P I C - 9 4 5 7 Chapter General Information 1- 1 Chapter 1 General Information...

  • Seite 9: Introduction

    In addition to the PC/104-Express expansion, EPIC-9457 also features one EIDE, two SATA, one Type II CompactFlash for the storage and six USB 2.0 ports, four COM ports, 8-bit Digital I/O for flexible I/O expansion. EPIC-9457 is an excellent choice for your vital applications. 1- 2...

  • Seite 10: Features

    E P I C B o a r d E P I C - 9 4 5 7 1.2 Features Intel® Atom™ N270 Processor Intel® 945GSE + ICH7M DDRII 400/533 Memory, Max. 2GB Gigabit Ethernet x 2 CRT, DVI or 24-bit Dual-channel LVDS LCD, TV AC97 2.

  • Seite 11: Specifications

    E P I C B o a r d E P I C - 9 4 5 7 1.3 Specifications System Form Factor EPIC Express Board Processor Onboard Intel® Atom™ N270 Processor 1.6GHz, FSB: 400/533MHz System Memory 200-pin DDRII SODIMM x1, Max. 2GB (DDRII 400/533) Chipset Intel®...
  • Seite 12 E P I C B o a r d E P I C - 9 4 5 7 Board Size 4.5" x 6.5" (115mm x 165mm) Gross Weight 1.1 lb (0.5KG) Operation Temperature 32° F ~ 140° F (0° C ~ 60° C) Storage Temperature -40°...
  • Seite 13 E P I C B o a r d E P I C - 9 4 5 7 USB2.0 x 6 PS/2 Port Keyboard+Mouse x 1 Digital I/O Supports 8-bit (programmable) Audio Line-in, Line-out, Mic-in & CD-in Touch Screen Optional 1- 6 Chapter 1 General Information...

  • Seite 14: Chapter 2 Quick Installation Guide

    E P I C B o a r d E P I C - 9 4 5 7 Chapter Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters further installation instructions, please refer to the user manual CD-ROM that came with the product.

  • Seite 15: Safety Precautions

    E P I C B o a r d E P I C - 9 4 5 7 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components.

  • Seite 16: Location Of Connectors And Jumpers

    E P I C B o a r d E P I C - 9 4 5 7 2.2 Location of Connectors and Jumpers Component Side Chapter 2 Quick Installation Guide...
  • Seite 17 E P I C B o a r d E P I C - 9 4 5 7 Solder Side Chapter 2 Quick Installation Guide...

  • Seite 18: Mechanical Drawing

    E P I C B o a r d E P I C - 9 4 5 7 2.3 Mechanical Drawing Component Side Chapter 2 Quick Installation Guide...
  • Seite 19 E P I C B o a r d E P I C - 9 4 5 7 Solder Side Chapter 2 Quick Installation Guide...
  • Seite 20 E P I C B o a r d E P I C - 9 4 5 7 Chapter 2 Quick Installation Guide...

  • Seite 21: List Of Jumpers

    E P I C B o a r d E P I C - 9 4 5 7 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Jumpers Label...

  • Seite 22: List Of Connectors

    E P I C B o a r d E P I C - 9 4 5 7 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: Connectors Label...
  • Seite 23 E P I C B o a r d E P I C - 9 4 5 7 CN21 COM4 Connector CN22, CN23 GIGA Ethernet Connector CN24 COM1, COM2 Connector CN25 VGA + DVI Display Connector CN26 Compact Flash Disk Connector CN27 Stand by power output Connector CN28...

  • Seite 24: Setting Jumpers

    E P I C B o a r d E P I C - 9 4 5 7 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.

  • Seite 25: Vio Voltage Selection (Jp1)

    E P I C B o a r d E P I C - 9 4 5 7 2.7 VIO Voltage Selection (JP1) Function +3.3V (Default) 2.8 24-bit LVDS Operating Voltage Selection (JP2) Function +3.3V (Default) 2.9 Clear CMOS (JP3) Function Protected (Default) Clear...

  • Seite 26: Touch Screen 4, 5, 8 Wire Selection (Jp7)

    E P I C B o a r d E P I C - 9 4 5 7 +12V 2.13 Touch Screen 4, 5, 8 Wire Selection (JP7) Function 4, 8 wire (Default) Open 5 wire 2.14 COM2 Ring/ +5V/ +12V Selection (JP8) Function +12V Ring (Default)

  • Seite 27: 24-Bit Inverter Power Connector (Cn2)

    E P I C B o a r d E P I C - 9 4 5 7 IDE LED (+) IDE LED (-) Power LED (+) Power LED (-) Reset Switch (+) Reset Switch (-) 2.17 24-bit Inverter Power Connector (CN2) Signal Signal LCD Inverter Power...

  • Seite 28: Wide Voltage Power Connector (Cn5)

    E P I C B o a r d E P I C - 9 4 5 7 2.19 Wide Voltage Power Connector (CN5) Signal Signal PGND PGND DC In DC In The minimum power consumption for booting is 25Watts without any connecting device.

  • Seite 29: 18-Bit Inverter Power Connector (Cn9)

    E P I C B o a r d E P I C - 9 4 5 7 LVDS1_TX1- LVDS1_TX1+ LVDS1_TX2- LVDS1_TX2+ LVDS2_TX0- LVDS2_TX0+ LVDS2_TX1- LVDS2_TX1+ LVDS2_TX2- LVDS2_TX2+ PPVCC LVDS2_TXCLK- LVDS2_TXCLK+ 2.22 18-bit Inverter Power Connector (CN9) Signal Signal LCD Inverter Power Backlight Control Backlight Enable 2.23 TV-out Connector (CN10)
  • Seite 30 E P I C B o a r d E P I C - 9 4 5 7 USBD5+ USBD6+ USBD6- 2-17 Chapter 2 Quick Installation Guide...

  • Seite 31: Lpt Port Connector (Cn12)

    E P I C B o a r d E P I C - 9 4 5 7 2.25 LPT Port Connector (CN12) Signal Signal #STROBE #AFD DATA0 #ERROR DATA1 #INIT DATA2 #SLIN DATA3 DATA4 DATA5 DATA6 DATA7 #ACK BUSY SELECT 2.26 System Fan Connector (CN13) Signal...

  • Seite 32: Power Output Connector (Cn15)

    E P I C B o a r d E P I C - 9 4 5 7 Port7 Port8 Mapping Table: BIOS Connector IT8781 GPIO Address Setting Definition Setting Port 8 @684h CN14 Pin 8 GPIO Set 5 / Bit 2 U26 Pin 9 (GPIO 52) Port 7 @684h CN14 Pin 7 GPIO Set 5 / Bit 1...

  • Seite 33: Touch Screen Connector (Cn18)

    E P I C B o a r d E P I C - 9 4 5 7 2.30 Touch Screen Connector (CN18) 8-wire Signal 4-wire Signal 5-wire Signal Ground Ground Ground Top Excite UL(Y) Bottom Excite Bottom UR(H) Left Excite Left LL(L) Right Excite...

  • Seite 34: Onboard Bios Programming I/F (Cn28)

    E P I C B o a r d E P I C - 9 4 5 7 2.33 Onboard BIOS Programming I/F (CN28) Signal Signal +3.3 Volt. Ground SPI_CE# SPI_CLK SPI_SO SPI_SI 2.34 Primary EIDE Connector (IDE1) Signal Signal IDE RESET DATA7 DATA8...
  • Seite 35 E P I C B o a r d E P I C - 9 4 5 7 CS#1 CS#3 2-22 Chapter 2 Quick Installation Guide...
  • Seite 36 E P I C B o a r d E P I C - 9 4 5 7 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Main Board/ Daughter Board/ Backplane 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI))

  • Seite 37: Chapter 3 Award Bios Setup

    E P I C B o a r d E P I C - 9 4 5 7 Chapter Award BIOS Setup Chapter 3 Award BIOS Setup 3-1...

  • Seite 38: System Test And Initialization

    3. The CMOS memory has lost power and the configuration information has been erased. The EPIC-9457 CMOS memory has an integral lithium battery backup for data retention. However, you will need to replace the complete unit when it finally runs down.

  • Seite 39: Award Bios Setup

    E P I C B o a r d E P I C - 9 4 5 7 3.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off.
  • Seite 40 E P I C B o a r d E P I C - 9 4 5 7 PnP/PCI Configurations This entry appears if your system supports PnP/PCI. PC Health Status Use this menu to set PC Health Status. Frequency/Voltage Control Use this menu to specify your settings for auto detect DIMM/PCI clock and spread spectrum.

  • Seite 41: Chapter 4 Driver Installation

    E P I C B o a r d E P I C - 9 4 5 7 Chapter Driver Installation 4 - 1 Chapter 4 Driver Installation...
  • Seite 42 E P I C B oa r d E P I C - 9 4 5 7 The EPIC-9457 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 –...
  • Seite 43 E P I C - 9 4 5 7 4.1 Installation: Insert the EPIC-9457 CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 5 in order. Step 1 – Install INF Update Utility v8.2.0.1014 Driver 1.
  • Seite 44 E P I C B oa r d E P I C - 9 4 5 7 2. Double click on the setup.exe file in the OS folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically Step 5 –...

  • Seite 45: Appendix A Programming The Watchdog Timer

    E P I C B o a r d E P I C - 9 4 5 7 Appendix Programming the Watchdog Timer Appendix A Programming the Watchdog Timer A-1...

  • Seite 46: Programming

    E P I C B o a r d E P I C - 9 4 5 7 A.1 Programming EPIC-9457 utilizes 8781 chipset watchdog timer controller. Below are the procedures to complete its configuration and AAEON initial watchdog timer...
  • Seite 47 E P I C B o a r d E P I C - 9 4 5 7 There are three steps to complete the configuration setup: (1) Enter the MB PnP Mode; (2) Modify the data of configuration registers; (3) Exit the MB PnP Mode.
  • Seite 48 E P I C B o a r d E P I C - 9 4 5 7 WatchDog Timer Configuration Registers Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.
  • Seite 49 E P I C B o a r d E P I C - 9 4 5 7 Watch Dog Timer 1, 2, 3 Configuration Register (Index=72h, 82h, 92h Default=001s0000b) Watch Dog Timer 1,2,3 Time-Out Value (LSB) Register (Index=73h,83h,93h, Default=38h) Watch Dog Timer 1,2,3 Time-Out Value (MSB) Register (Index=74h,84h,94h Default=00h) Appendix A Programming the Watchdog Timer A-5...
  • Seite 50 E P I C B o a r d E P I C - 9 4 5 7 A.2 ITE8781 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting...
  • Seite 51 E P I C B o a r d E P I C - 9 4 5 7 call Superio_Set_Reg ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1:...
  • Seite 52 E P I C B o a r d E P I C - 9 4 5 7 CALL Write_Configuration_Data Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,81h JNE Not_Initial Need_Initial: Not_Initial: Check_Chip ENDP...
  • Seite 53 E P I C B o a r d E P I C - 9 4 5 7 OUT DX,AL MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL Write_Configuration_Data ENDP Superio_Set_Reg proc near...
  • Seite 54 E P I C B o a r d E P I C - 9 4 5 7 Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main...

  • Seite 55: Appendix B I/O Information

    E P I C B o a r d E P I C - 9 4 5 7 Appendix I/O Information Appendix B I/O Information...

  • Seite 56: I/O Address Map

    E P I C B o a r d E P I C - 9 4 5 7 B.1 I/O Address Map Appendix B I/O Information...
  • Seite 57 E P I C B o a r d E P I C - 9 4 5 7 B.2 1 MB Memory Address Map B - 3 Appendix B I/O Information...

  • Seite 58: Irq Mapping Chart

    E P I C B o a r d E P I C - 9 4 5 7 B.3 IRQ Mapping Chart B.4 DMA Channel Assignments Appendix B I/O Information...

  • Seite 59: Appendix C Mating Connector

    E P I C B o a r d E P I C - 9 4 5 7 Appendix Mating Connecotor C - 1 Appendix C Mating Connector...

  • Seite 60: List Of Mating Connectors And Cables

    E P I C B o a r d E P I C - 9 4 5 7 C.1 List of Mating Connectors and Cables The table notes mating connectors and available cables. Connector Function Mating Connector Available Cable P/N Label Cable Vendor Model no...
  • Seite 61 E P I C B o a r d E P I C - 9 4 5 7 compatible) 2.00mm Pitch 26 LPT port pins ( CATCH CN12 LPT cable 1701260308 CATCH Connector H754-2x13 or compatible) (HoBase System Fan CPU fan 2543-WS-3 or CN13 HoBase...

Inhaltsverzeichnis