Technical Data; Care And Cleaning - Renkforce 1590178 Bedienungsanleitung

• Plug the power adapter into a standard mains socket.
• When the connected devices have finished charging, turn off the corresponding port using
the on/off switch (4) and unplug the power adapter from the mains socket.
b) Connecting and charging USB devices
• Connect the USB cable on your device to a USB port (2) on the USB hub.
Refer to the technical data of the mobile device that you are going to charge and
note output power of the corresponding port. You can connect up to four mobile
devices to the USB port, which are charged with the total available power.
• To start the charging process, press the on/off switch (4) for the corresponding port. The
USB port will start to deliver a charging current and the corresponding LED indicator (1) will
turn green.
The USB hub features smart control. It automatically detects the charging current
and specifications for the connected device. For example, Apple
automatically recognized and charged with the native Apple
• Monitor the charging process. Use the on/off switch (4) to pause or end charging.
• Alternatively, you can also pause the charging process by disconnecting the USB cable from
the USB hub and the mobile device(s).
• When the device has finished charging, disconnect the USB cable from the product and the
connected device.
It is recommended to switch off USB ports that are not in use (use the on/off
switch (4)).
c) Capacity of the USB ports
Ports 1 and 3
• These two ports each provide an output voltage of 5 V/DC and output current of max 4.0 A.
Ports 2 and 4
• These two ports each provide an output voltage of 5 V/DC and output current of max 4.0 A.
The total maximum output current of all the ports is 7 A.
d) Short circuit and overload protection
All four ports feature built-in short circuit and overload protection.
• Each USB port is connected to another port to protect against overload. For safety reasons,
the device switches off automatically in the event of a combined overload (over 4 A) on the
first and second or third and fourth ports.
• Disconnect the load and power supply. Restart the device by reconnecting the power supply
and load.
When charging a device with a Y-cable, the connected ports will switch off if the
total current exceeds 4 A. To prevent the USB ports from switching off, the Y-cable
should be connected to the first and third or second and fourth ports. This enables
the charging device to use the full charging power of the USB hub (more than 4 A)
without triggering the overload protection feature.

Care and cleaning

• Before cleaning the product, switch it off and disconnect it from the mains.
• Before cleaning the product, unplug the USB cable and disconnect any connected mobile
devices from the power supply.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• This product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
• A dry, soft and clean cloth is sufficient for cleaning. Do not press too hard on the housing, as
this can lead to scratch marks.
• Do not immerse the product in water.
• Dust can be easily removed using a soft and clean long-haired brush.
Disposal
You thus fulfil your statutory obligations and contribute to protection of the environment.

Technical data

a) USB hub
Input voltage / current ................... 12 V/DC, 3 A
Output voltage/current, ports 1–4 .. 5 V/DC, max. 7 A (total)
Number of ports ............................ 4
Operating conditions ..................... 0 to +50 °C, 20–95 % relative humidity (non-condensing)
devices are
®
Storage conditions ........................ -20 to +60 °C, 20–95 % relative humidity (non-condensing)
charging specifications.
®
Dimensions (W x H x D) ............... 126 x 55 x 31 mm
Weight .......................................... 340 g (with power adapter)
b) Power adapter
Input voltage ................................. 100–240 V/AC, 50/60 Hz
Output voltage/current .................. 12 V/DC, 3 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
*1590178_v1_0318_02_DS_m_4L_(1)