Kontroik JIVE Pro 80+ HV Bedienungsanleitung Seite 20

Using different batteries with equal number of
cells leads to steady RPM even when changing
the between batteries of differing performance
levels.
Governor Store is not able to compensate for
packs with different cell counts.
Therefore, in mode 4 with governor store
activated, it is not possible, for example, to
program with a 10S battery and expect the same
RPM with a 12S battery afterwards.
When changing the set-up (battery cell
!
count, motor, gearing, rotor blades, etc.)
mode 4 must be reprogrammed when
governor store is activated!
Autorotation (bail out) is an integral part of mode
4. It cannot be selectively programmed with or
without AR.
Low voltage slow
protection) is active, therefore the motor's RPM is
slowed, when the adjusted battery discharge
!
voltage is reached (see 3.4).
Smooth start is at 12 s on default, but can adjust
with the programming unit form 8 up to 60 s.
Also, the BEC voltage is adjustable via the
programming unit from 5 V up to 8 V in 0.1 V
steps (see 4.3).
Preparing the transmitter
Using a flight mode switch, you may chose among
several different head speeds. In each mode, you
may set a different straight line throttle value.
Some values for example:
Example Set-up for Heli mode:
Start / motor off:
Hover (Idle 1):
Scenic flight (Idle 2):
3D-flight
The JIVE Pro should not be used with a
!
throttle value higher than 80 % in Heli Mode,
as it needs at least 20 % head room for
proper governing.
For the AR (bail out) (mode 4 only), throttle hold
must be set to 25 % (30% for Futaba).
By setting this value the AR function is activated
automatically, no further settings are necessary
for using AR in mode 4.For further information of
transmitter programming,
!
transmitter's manual.
20
down (deep discharge
0 %
45 %
60 %
80 %
please see
Programming mode 4:
For AR mode, use there is in addition to 100 %
(full throttle) and 0 % (motor off) position a third,
the AR-on-position necessary. It is recommended
to set the AR-on-position to exact 25% (30% for
Futaba).
For the following mode-programming only two
positions on this previously prepared switch are
needed:
Before beginning, set all throttle trims and sub
1.
trims to zero, set throttle travel adjust to 100 /
100, and set your beginning throttle curve for
programming from 0-100 % (see also from 3.1
on).
Turn on the transmitter and move the throttle
2.
stick to the 0 % position.
Connect the BEC cable to the receiver's port
3.
(throttle function) and the other side into the
JIVE Pro's port that is marked Master. Then
switch on the transmitter.
Connect the motor cables to the motor (pay
4.
attention to the motor's direction of rotation, e.g.
exchange two of the motor cables or exchange
via programming unit.
Connect the main battery to the JIVE Pro.
5.
LED flashes. You will hear a three ascending
6.
tones, acknowledging the activation. Next, you
will hear single tones for the recognized
number of cells (see 4.1).
After hearing the cell count, pull the Jumper
7.
cable out on the ESC (see 5 / sketch - No. 7),
you will hear three descending tones and the
mode. Next, the JIVE Pro begins counting the
modes, for each mode there is the equal
the
number of single beeps (mode 1 - one beep,
mode 2 - two beeps, etc), the LED also flashes
in correspondence with the beep number.
After 4 single beeps mode 4 is reached, move
8.
the throttle stick to the full throttle position (100
%). The LED lights and the ESC confirm first
the throttle position with three ascending
tones, then the mode with 4 single beeps.
Position 1 = 0 %
Position 2 = 100 % full throttle
2
2
1
1
Check programming
afterwards!
motor off