Behringer XD8USB Schnellstartanleitung Seite 12

22 XD8USB
XD8USB Getting started
Getting started PLAYING
(EN)
Play the kit and adjust the volume in your headphones
or external sound system to a safe listening level.
Each drum head or cymbal can give diff erent sounds
depending on where it is hit:
1. Assemble the drum kit as shown in the
assembly instructions, and tighten
Crash and Ride
all connections.
Snare
Rim
Toms
2. Connect the cables to the drum pads,
cymbals and foot pedals, as shown in the
hook-up diagram.
3. Connect headphones or make connections to
any external sound equipment such as an
external amplifi er, or active speaker. See the
Hi-Hat
hook-up diagram for some ideas.
Phones
Phones
DC IN
Bow Shot with:
Power
Adapter Pedal Open
Pedal Closed
4. Connect the power supply adapter to the local
mains supply. This universal adapter can accept
mains voltages from 100 VAC to 240 VAC.
Pedal Only: Press down for "Chick"
Connect the DC output to the drum module.
Kick
5. Do not turn on the drum module until all
connections have been made.
6. Turn down the VOLUME control on the drum
module, and turn on the POWER switch.
7. If you are using external sound equipment,
turn it on after the drum module. At the end of
the session, turn any external sound equipment
off fi rst.
KIT
1. Press KIT and the current kit number will
be displayed.
2. Press + or – to select from 10 preset kits, or 5
user kits 11 to 15. Play each kit to hear how
it sounds.
Bow
3. If required, press VOLUME and adjust the kit
volume using + or –.
Head
4. To save this as a new kit, press SAVE/REC and
press + or – to choose from 11 to 15.
Head
5. Press SAVE/REC again to save the new user kit.
Bow
PATTERN
There are 40 diff erent patterns available for practice.
Pattern 41 is reserved for recording your own playing
while in recoding mode.
1. Press START/STOP to start the pattern.
Kick 2. Press PAT to display the current pattern number.
3. Press + or – to select a pattern.
23 Quick Start Guide
4. To adjust the pattern volume, press VOLUME 4. If required, press VOLUME and adjust the voice
and adjust using + or –. (You can hear your volume using + or –.
drum playing better by turning down the
pattern volume.)
5. When you like the way the pads sound,
save this as a new user kit. Press SAVE/REC and
press + or – to choose from 11 to 15.
5. Press TEMPO and the current tempo will be
displayed. Press + or – to adjust.
6. Press SAVE/REC again to save the new user kit.
DRUM OFF
1. Press DRUM OFF to mute/unmute the drum
CLICK
track from the pattern play.
1. Press CLICK to start the metronome and display
the current signature.
VOICE
You can change the sound (voice) of each pad, and
save your settings as a new user kit.
2. Press + or – to change the signature.
1. Press VOICE and the current voice number will
be displayed.
3. Press TEMPO to display the current tempo.
2. Press the pad button of the drum or cymbal
you want to change.
4. Press + or – to adjust the tempo.
5. Press CLICK again to stop the metronome.
3. Press + or – to choose from 123 diff erent
sounds. Press the pad to listen. Note that the
Hi-Hat has four options.
Recording
1. Press-and-hold SAVE/REC to enter
recording mode.
2. If desired, press + or – to select a kit.
3. Press START/STOP and recording will begin in a
few seconds.
4. Play the drum kit, and your playing will be
recorded as pattern 41.
5. Press START/STOP again to stop the recording.
Playback
6. While Pattern 41 is displayed, press START/
STOP to play the recording.
7. To play your recording later, press PAT and
press + or – to select pattern number 41.