Table of Contents Table of Contents Deutsch ..................... 1. Bevor Sie anfangen ................Installation der Hardware ..............Konfiguration des Umschalters ............Troubleshooting ..................Version 04.04.2009...
1. Bevor Sie anfangen Packungsinhalt TEG-S2620is Mehrsprachige Installationsanleitung CD mit Bedienungsanleitung RS-232-Kabel Stromkabel Montagesatz für Gestell Gummifuesse Systemanforderungen Webbrowser: Internet Explorer (6 oder 7) Computer mit korrekt installiertem Netzwerkadapter RJ-45-Netzwerkkabel Optionale Geräte Standardmäßiges 19”-Gestell Mini-GBIC-Modul (z.B. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40, TEG-MGBS80, TEG-MGBS10D3_D5, TEG-MGBS40D3_D5) für Mini- GBIC-Steckplätze...
Hinweis: Die Mini-GBIC Ports sind gemeinsam mit Gigabit Ethernet Ports 25 und 26 verbunden. D.h. bei Einsatz der Mini-GBIC-Ports, werden Ports 25 und 26 deaktiviert. 1. Schließen Sie das Stromkabel an der Rückseite des TEG-S2620is an und stecken Sie es in eine Steckdose. 2. Verbinden Sie den Computer über...
3. Configuration du Switch Hinweis: Es ist zu empfehlen, den Switch von einem verdrahteten Computer aus zu konfigurieren. Bevor Sie den Switch konfigurieren können, müssen Sie dem Netzwerkadapter Ihres Computers eine statische IP-Adresse im Subnetz 192.168.0.x zuweisen. Die standardmäßige IP-Adresse des Switch lautet 192.168.0.1.
Seite 6
HyperTerminal 1. Verbinden Sie einen seriellen Port Ihres Windows-PCs über das RS- 232-Kabel mit dem Konsolenport Ihres Umschalters. 2. Gehen Sie zu Start > Programs (Programme) > Accessories (Zubehör) > Communications (Kommunikation) > HyperTerminal. 3. Geben Sie einen Namen ein, wählen Sie ein Symbol aus und klicken Sie dann auf OK.
Seite 7
4. Wählen Sie den korrekten COM- Port (z.B. COM1, COM2) und klicken Sie dann auf OK. Konfigurieren Sie die folgenden Einstellungen, klicken Sie auf Apply (Übernehmen) und anschließend auf OK: Bits pro Sekunde: 9600 Datenbits: Parität: None (Nein) Stoppbits: Flusssteuerung: None (Nein) 6.
Seite 8
Trendnet unter http://www.trendnet.com. Registrieren Sie Ihr Produkt Nehmen Sie sich bitte einen Moment Zeit und registrieren Sie Ihr Produkt online, so dass Sie unsere umfassenden Support- und Kundendienstleistungen in Anspruch www.trendnet.com/register nehmen können: Vielen Dank für den Kauf eines TRENDnet-Produkts Deutsch...
IP address in the subnet of 192.168.0.x. I typed http://192.168.0.1 in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TEG-S2620is's web configuration page? First, check your hardware settings again by following the instructions in section 2.
Seite 10
HyperTerminal? Bits per Second: 9600; Data bits: 8; Parity: None; Stop bits: 1; Flow control: None. I changed the IP address of the switch, but I forgot it. How do I reset my TEG-S2620is? Follow the instructions below: 1) Connect the RS-232 cable from a serial port on your Windows PC to the console port on your computer.
Seite 11
Return Material Authorization (RMA) number, accompanied by a copy of the dated proof of the purchase. Products returned to TRENDnet must be pre- authorized by TRENDnet with RMA number marked on the outside of the package, and...
Seite 12
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF TRENDNET’S PRODUCTS. TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S...
Seite 13
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.