Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Connect according to mode
Separate switching of two lamps
Fig. 3:
N = neutral wire (blue)
L = phase (black)
^ = lamp 1
v = lamp 2
Blind control
Fig. 4:
N = neutral wire (blue)
L = phase (black)
^ = motor connection "open"
v = motor connection "close"
M = blind motor
Timer for stairway light
Fig. 3:
N = neutral wire (blue)
L = phase (black)
^ = time controlled stairway light
v = other lamp
Choose mode
Important: Choose mode first, than start programming!
Subsequent change of mode deletes all programmings!
Fig. 5:
Separate switching of two lamps
= mode A
Blind timer
= mode B
Timer for stairway light
= mode C
Teaching Fig. 7 / 8
• All receivers must be programmed onto the button to
which it is meant to react.
1. The programming mode is activated for about
1 minute by pushing the „LEARN" button of the product
for about 2 seconds. Thereby the red LED is flashing with
a frequency of 1Hz.
2. Now the device must be chosen on the remote control
and transmitted to the receiver by pushing the „ON"
button or operation the rocker switch.
Group membership
Decide wheter the switch power socket is to react to a
group call (device group 0). (See switch on the backside)
Only in combination with remote control type 84471-B.
Fig. 6:
ON
Must react
OFF
Must not react
Switching
Note: The figures show a key transmitter.
The programming of other transmitters is identical.
Separate switching of two lamps (mode A)
Fig. 14:
Switch lamp 1 (channel 1)
Switch on = push ON
Switch off = push OFF
ANL_84476-B.indd 4
Fig. 15:
Switch lamp 2 (channel 2)
Switch on = push ON
Switch off = push OFF
Blind switching (mode B)
Fig. 16:
Open blind: push ON
Stop blind: push ON again
Close blind: push OFF
Stop blind: push OFF again
Timer for stairway light (mode C)
Fig. 17:
Switch stairway light (channel 1)
Switch on = push ON
Switch off = automatically according to
adjusted time (Fig. 9)
Fig. 18:
Switch other lamp (channel 2)
Switch on = push ON
Technical data
• Range: 100m (free field)
• Supply voltage: 230V~, 50Hz
• Power: 500W
• Inductive load: 1150VA (cos(phi)=0,8)
• Fuse: T6,3A H 250V~
• Frequency: 868MHz
• Own power consumption: <0.5 Watt
• Number of device groups: 2
• Number of devices per device group: 10
• Wiring: solid or standard rigid 1.5mm²
• Pollution degree: IP20
CE Declaration of Conformity
REV Ritter hereby declares that the 84476-B
model is in accordance with the underlying
requirements and other relevant provisions
868MHz
of Directive 1999/5/EC. For the complete CE
Declaration of Conformity please refer to
www.rev.biz under the article in question. This
product is a radio controlled system and should
only be used as this. The buttons of the remote
control could not be used permanently.
WEEE-reference of disposal
In accordance with European defaults used
electrical and electronics devices may no more
be given to the unsorted waste. The symbol of
the waste bin on wheels refers to the necessity
of separate collection. Please help with environ-
mental protection and see to it that this device is
given to the for this purpose designated systems
of waste sorting if you do not use it any longer.
GUIDELINE 2002/96/EG of the EUROPEAN
PARLIAMENT AND the COUNCIL of January 27th
2003 about electrical and electronics old devices.
Warranty
During manufacturing this REV product is passed through
several quality testing stations which are set up with newest
technology. Should nevertheless a defect arise, REV offers a
warranty to the following extent:
1. The duration of the warranty is 24 months after the date
of purchase.
2. The unit is either repaired or replaced by REV free of
charge or if it can be shown that it has become unusable
during the warranty period due to a manufacturing or
material defect.
3. The liability does not cover transport damages or
damaged incurred through defective installation.
4. If REV repudiates the warranty claim and no objection is
made within 6 months, the right to repair becomes
time-barred.
5. In a warranty case the unit must be sent to the dealer or
REV together with the sales slip and a short description of
the defect.
6. If there is no proof for a warranty liability being in place,
any repair carried out will be invoiced.
REV Ritter GmbH • Frankenstr. 1-4 • D-63776 Mömbris
Tel. +49 900 117 1070 • E-Mail: service@rev.biz • www.rev.biz
29.01.2013 11:34:11
Werbung
