Werbung
Verfügbare Sprachen
Verfügbare Sprachen
User Manual
Art.Nr. 193 1xx2 / 194 1MS2
IR-EASY / IR-EASY USB
General
IR-EASY is available in two models.
P/N 193 1xx2 Infrared to Easywave converter in a straight
through power socket. Power supply 230V.
The power outlet cannot be switched on/off.
P/N 193 9xx1 Additional IR receiver with mounting set.
P/N 194 1MS2 Infrared to Easywave converter in a small infra-
red penetrable box with USB power supply.
There are 4 IR device addresses possible which allows to
operate up to 4 IR-EASY devices in the same room.
With IR-address 1 you can also use the signals from the IR
power socket to control the first 8 radio signals (1 A/B to 4 A/B).
New in version 3.1:
In the first 10 Sec. the IR-address is set automatically with a
valid signal. Blue LED stays on while this time and blinks x times
( x = IR address) after that.
Technical Specs
Power Supply:
230V AC or 5V DC (USB)
Channels:
8 x Easywave A/B, 16 Signals
Dimensions:
120x48x65mm or 51x82x14mm (USB)
Weight:
170g or 70g (USB)
2
green: IR-Receiver
blue: Prog.-Time / valid IR Signal
1
red: Radio Transmitter
3
1: Straight through power outlet
2: IR receiver and LEDs
3: Socket for external IR receiver
How to use
- As soon as IR-EASY receives an IR signal the green LED inside
starts flashing. It also flashes if any IR signal is received.
- If a valid signal is received (correct IR-EASY address) the internal
red and blue LED lights up additionally. The red LED shows an
Easywave signal being transmitted.
- If only the green LED flashes please make sure the IR-EASY is
set to the correct address.
English
2
Sybility GmbH, Kreuzweg 15, 91781 Weißenburg, T: 09141-9131689, F: 09141-9132855
Setting the Device Address
If you are planning to use more than one IR-EASY in the same
room, each one must be set to a different IR address.
The setting can be done by sending an IR signal from the remote
control to the IR-EASY within the first 10 sec. after the IR-EASY is
plugged in (blue LED is on).
After the 10 sec or if an IR signal was received the blue LED
flashes x times (x = IR address).
1. First select the address
on the remote control
regarding this table:
2. Send any signal from the
remote to change the address in the IR-EASY infrared
receiver. IR-EASY will now work with the signals of that IR
device address.
Please make sure that only one IR-EASY is powered when
setting the device address.
Remote Control
Safety and Mounting Instructions
-
IR-EASY may only be used in dry rooms.
-
Cleaning only when not connected to power supply and only
with a clammy cloth.
-
If there is a LED / LCD TV in the same room make sure to test
the functionality of IR-Easy when the TV is running. These
devices can transmit infrared light which can interfere with
the reception of IR-EASY.
-
Position IR-EASY so that it is not directly under synthetic
light or in sunlight, this can lower the reception of the IR
receiver.
Scope of Delivery
IR-EASY:
Additional IR Receiver for IR-Easy:
IR-EASY USB:
Select IR Address
Key
Signal
Easywave
1 :
1
2 :
2
3 :
3
4 :
4
5 :
5
6 :
6
7 :
7
8 :
8
9 :
9
0 :
10
:
11
:
12
:
13
:
14
:
15
:
16
IR-EASY
User manual
IR-Receiver
Mounting Set
IR-EASY USB
User Manual
Stand 11/2017
1A
1B
2A
2B
3A
3B
4A
4B
5A
5B
6A
6B
7A
7B
8A
8B
Werbung
