Superrollo TA70-CSG Bedienungsanleitung Seite 2

Instructions for
EN
Radio code switch TA70-CSG
Item no: SR40082
BA40082-A (07.13)
7. CE Mark and EC Conformity
The present product complies with the requirements of the current
European and national directives.
1999/5/EC
R&TTE directive
Conformity has been verified. The corresponding declarations and
documentation are available on file at the manufacturer's premises.
Please send equipment for repair to:
DPD GeoPost
superrollo Hausautomatisierung GmbH
Werrastraße 12
45768 Marl (Germany)
superrollo Hausautomatisierung GmbH
Gewerbepark 1
01156 Dresden (Deutschland)
www.superrollo-online.de
Service:
Hotline 01807 001655*
* 30 Sec. free of charge, subsequently 14 cents/minute from german fixed line
networks and max 42 cents/minute from German cellular networks.
1. General view
1
2
3
4
7
5
6
1. Button panel
2. Upper housing
3. Button sheet
4. Control board
5. Battery
6. Base housing
7. (*)-key
8. (#)-key
2. Installation
1. Remove the button panel with a screw driver.
2. Screw out the screws and remove the upper housing
and the button sheet.
3. Put the base housing against the selected location on
the wall and make marks on the wall though the
installation holes with a pencil. Drill holes of 3 mm
for wood or 5 mm for masonry.
4. Install the base housing to the wall. Reinstall the but-
ton sheet and the upper housing, and screw it securely
to the base housing. To avoid cracking the plastic
housing, do not over tighten.
5. Reinstall the button panel to the upper housing.
3. Battery
2 × 3 V battery, maxell CR2032
The power of the 2 pieces 3 V battery should last at least 1 year. As
long as the power is adequate, the keypad will light up and will active
the operator when the code and button „#" or „*" -button are pressed.
Replace the battery when the light is dim.
Replacing battery:
1. Repeat Step 1 & 2 of installation procedure.
2. Remove the screws on the control board and take it out
of the base housing.
8
3. Replace the batteries behind the control board with
2 new ones.
NOTE
Please take notice to the polarity.
4. Programming
4.1 Code
The original code is „0000".
It can be reset to be any code with minimum 1 figure and maximum
8 figures. For example, the code can be „8", or „55667788". There
can be more than 100 million possible combinations.
4.2 Code resetting
1. Press both key „ *" and key „ #" for about 5 seconds till the
red light flashes slowly.
2. Input the former code and press key „ #", the red light will
flash quickly.
3. Now input the new code and press key"#", the red light
will be on for 2 seconds and then go off. Now the code
has been reset.
4. Programming
4.3 Programming to the RolloPort garage door
opener.
1. Switch the RolloPort in to the registered mode
(please refer the RolloPort instructions).
2. Input the code figures on the keypad and press key „ #" or
key „ *". Now the opener has learned the keypad's code.
5. Operating
5.1 Enter your code and then press key „ #" or key „ *".
5.2 The door will now move.
6. Warranty conditions
Superrollo Hausautomatisierung GmbH provides a24-month war-
ranty for new systems that have been installed in compliance with the
installation instructions. All construction faults, material defects and
manufacturing defects are covered by the warranty.
The following are not covered by the warranty:
◆ Incorrect fitting or installation
◆ Non-observance of the installation and operating instructions
◆ Improper operation or wear and tear
◆ External influences, such as impacts, knocks or weathering
◆ Repairs and modifications by third party, unauthorised persons
◆ Use of unsuitable accessories
◆ Damage caused by unacceptable excess voltage (e.g. stroke of
lightning)
◆ Operational malfunctions caused by radio frequency overlapping
and other such radio interference
Superrollo shall remedy any defects wich occur within the war-
ranty period free of charge either by repair or by replacement of the
affected parts or by supply of a new replacement unit or one to the same
value. There is no general extension of the original warranty period by
delivery of a replacement or by repair as per the terms of the warranty.