Operation - Pentatech DF-120TX Bedienungsanleitung

8. Connection
Connection of the transmitter
!
Connect the AV-input [8] of the transmitter DF-120TX [1] with the AV-
output of the source device using the AV cable [6] (yellow plug=video /
red plug=audio right / white plug= audio left). If required use
cinch/BNC adapters or an cinch/scart adapter (see chapter 15).
!
Connect the DC-plug of the mains adapter cable [10] to the mains adapter
connection [7] of the transmitter.
!
Connect the mains adapter with a suitable mains outlet. The power-LED
[2] and the connection-LED [4] illuminate and after approx. 3 seconds the
connection-LED is extinguished.
Connection of the receiver
!
Connect the AV-output [18] of the receiver DF-120RX [11] with the AV-
input of the source device using the AV cable [16] (yellow plug=video /
red plug=audio right / white plug= audio left).
!
Connect the DC-plug of the mains adapter cable [20] to the mains adapter
connection [17] of the transmitter.
!
Connect the mains adapter with a suitable mains outlet. The power-LED
[12] and the connection-LED [14] illuminate and after approx. 3 seconds
the connection-LED is extinguished. If wireless connection is established,
then the connection-LED will illuminate after approx. 4 seconds.

9. Operation

!
After connection of the power supplies the set is in operation.
!
Switch on the power for the source and display devices.
!
Select the AV input corresponding to the connection (on some TV sets this
may be depicted as VCR, channel 0, or with the
camera is connected through a recorder then select the corresponding AV
channel. You will now see the picture and hear the sound from the source
device.
!
The orientation of the antennas [5 and 15] can be adjusted to achieve the
best possible connection quality.
Note:
#
If there is no wireless connection the connection-LEDs [4 and 14] will not
24 - GB
illuminate and a message "NO SIGNAL" will appear on the display
monitor. In this case relocate the transmitter and receiver, reducing the
distance if possible. If there is still no connection then the transmitter and
receiver must be paired again (see chapter 10.1).
#
If the video stops or does not run smoothly adjust the antennas, change the
positions or reduce the distance between the transmitter and receiver.
#
A visual indication of the connection quality can be obtained after
removing the mains adapter [20] of the receiver from the mains supply
and then reconnecting this. A symbol with 0 to 4 bars will then show for
approx. 10 seconds in the top right hand corner of the picture on the
display monitor.
10. Functions
10.1 Connection pairing
The transmitter [1] and receiver [11] must be paired with each other to
establish the wireless connection. The transmitter delivered in the set is already
paired with the receiver.
If required the wireless connection can be established as follows:
!
Check that the cables are correctly connected, that transmitter and receiver
are powered (power LEDs [2 and 12] illuminate on the receiver DF-120RX)
and that these are located within the wireless range.
!
Hold the "Pairing"-button [19]
LED [14] flashes. On the display monitor the following message appears:
"Please press pairing button of TX device" and a timer counts down from 60
seconds.
!
Within the 60 seconds you have time to establish the connection as
follows. Press and hold the "pairing"-button [9]
symbol). If a
120TX until the connection LED [4] on the transmitter flashes. When
wireless connection is sucessfully established the following message will
appear on the display monitor: "Pairing OK save data". This message will
disappear after approx. 10 seconds and the picture from the AV-source will
appear. The connection LEDs [4 and 14] will illuminate green.
10.2 Using an Infrared Remote Control
If the source device has an infrared remote control this can be used from the
on the receiver pressed until the connection
on the transmitter DF-