Werbung
Quicklinks
Radio control model
R/C Flugmodell
INSTRUCTION MANUAL
MONTAGEANLEITUNG
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
TECHNISCHE DATEN
Spannweite
Lange
Elektroantrieb
(siehe nächste Seite)
Verbrennerantrieb
7.5cc 2-T / 8.5cc 4-T
Fernsteuerung
5 Kanal / 4 -5 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
SPECIFICATIONS
Wingspan
1620mm
Length
1250mm
Electric Motor
Glow Engine
Radio
(.46-.52 class glow conversion optional)
(7,5 -8,5cc Glühzündermotor Einbau möglich)
(See next page)
.46 2Stroke / .52 4-Stroke
5 Channel / 4 -5 Servos
63.7in.
49.2 in.
Werbung
Verwandte Anleitungen für VQ Model U.S.Army L4A Grasshopper
Inhaltszusammenfassung für VQ Model U.S.Army L4A Grasshopper
- Seite 1 Radio control model R/C Flugmodell INSTRUCTION MANUAL MONTAGEANLEITUNG Designed for brushless electric motors (.46-.52 class glow conversion optional) Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich) TECHNISCHE DATEN SPECIFICATIONS Wingspan 63.7in. Spannweite 1620mm Length 49.2 in. Lange 1250mm Electric Motor (See next page) Elektroantrieb...
-
Seite 2: Required For Operation (Purchase Separately) Benotigte Komponenten (Nicht Im Lieferumfang Enthalten)
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten) Propeller 11x8 for electric motor / 11x6 for glow engine Luftschraube 11x8 fur Elektromotor / 11x6 fur Verbrennungsmotor Extension cord Servoverlangerungskabel Brushless Motor Minimum 5 channel radio PICHLER BOOST 40 for airplane Brushless ESC Minimum 5 Kanal... - Seite 3 Align the mark on both Securely attach the engine mount to the mounts with the center fire-wall using the four 4x25mm screws. mark on the fire-wall Note the side thrust for motor! Sturz und Zug beachten! Set the engine on the engine mounting beams.
- Seite 4 Using a plywood motor mounting plate as a template, mark the fire wall where the four holes are to be drilled . 13/64” Remove the plywood motor mounting plate and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked above.
- Seite 5 2.5x8mm screw ....3 2.mm 2.mm 2.mm Cut two slots (3x7mm and 3mm deep) along the trailing edge of the horizontal stabilizer. TOP VIEW / Draufsicht HORIZONTAL STABILIZER TOP VIEW / Draufsicht 85mm 85mm Full the elevator out of the horizontal stabilizer. Cut away only the film both side...
- Seite 6 When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage. Cut away only the covering both side Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above.
- Seite 7 10mm Cut a slots (3x7mm and through both the covering and balsa wood) along the trailing edge of the vertical stabilizer. Cut away only the covering FRONT-VIEW Trial fit the vertical stabilizer in place. Check the alignment of the vertical stabilizer. If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps.
- Seite 8 Collar 0.5~0.6in. 1/8(3mm) screw 12~15mm 0.3in. 1/16 1.5mm Cut away the covering and balsa wood BOTTOM - VIEW / Unteransicht 3x12..2 1/16 1.5mm ......1 ......1 4X20mm screw ....4 Cut away only the covering * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement.
- Seite 9 3mm connector Connector 3mm connector ..4 3mm connector Aluminum landing gear Hauptfahrwerk BOTTOM - VIEW / Unteransicht 4X50mm screw ....2 4mm nut-washer 4mm nut 4mm nut 4x30mm 4x30mm screw screw 3mm connector Aluminum landing Aluminum landing gear Hauptfahrwerk gear Hauptfahrwerk FUSELAGE...
- Seite 10 ...1 Servo tray TOP VIEW Servo tray Elevator servo FRONT Elevator pushrod Throttle servo Throttle pushrod Rudder servo...
- Seite 11 Magnetic seating (front seating only) Magnetic piece.
- Seite 12 B’ Aluminum tube Aluminum tube B=B’ Note: check the length (B=B’) of the aluminum tube with the fuselage before glue. Aileron extension Aileron pushrod cord 1.2mm O Alenk-Gestange Trial fit the control horn into the slot. If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps.
- Seite 13 Note: The hole on the surface of the top of the 2.mm drill bit wing are pre-drilledat factory. Secure the wing in place using 3x15mm screw. Aluminum 3x15mm screw tube inside 3x15mm screw ..2...
- Seite 14 IN CASE OF FLOATING USING Rear landing gear mount Note: The rear landing gear mount is pre-installed at factory Rear landing gear not included 220mm BOTTOM - VIEW / Unteransicht 3x15mm screw ..6 Cut away only the covering ..4 Cut away the covering...
- Seite 15 0.5mm dia. Cable ...1 roll 2mm metal tube .....4 VQA086 FUEL 12 US. GALS 100 OCTANE US.ARMY LK4A AIRFORCE SERIAL NO 44 74298 Masking tape 5 min. Epoxy...
- Seite 16 Aileron 10mm 10mm Querruderausschlag 20mm Rudder 10mm Elevator 20mm Seitenruderausschlag 10mm Hohenruderausschlag 65 ~ 70mm Do not try to fly an out-of balance model! Uberprufen Sie vor dem Flug den Schwerpunkt. IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.