Table of Content Practice of sound Introduction Operating EDGE A2-300 Safety Instructions Quick Setup Connecting the speakers Placing the unit Bi-amping AC Power (220V / 110V) 19” rack mounting Connections (Noise issues) Technical Specifications Inputs & Outputs XTZ Values Our basic philosophy is to recreate a balanced and natural sound with an optimum relation between price, performance and quality.
DANGER! No user serviceable parts inside. Service is to be 11. Only attachments/accessories specified performed only by XTZ. manufacturer. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.
ON. If used in „ALWAYS ON“ Mode, the device will always be in ON Mode. 6 Switch the POWER switch on the rear panel to the “ON” setting in order to turn the EDGE A2-300 to stand- by mode. The Standby LED indicator embedded around the bezel of the STANDBY button will illuminate...
In standby mode (220V / 110V) the EDGE A2-300 consumes less than 0,3W. Connections To ensure a safe management of the amplifier and speakers, always only connect and disconnect signal cables and speaker cables when the amplifier is shut off with the main switch on the back side.
Power - AC Powe r inlet AC P o w er in p ut a n d FU S E c om pa rt m e nt . - Fus e Do o nl y re p la ce w i th “ T4 A H 250 V ” r at ed fu se . - Powe r S witch Mai n p o w er s w itch ( t ogg le ) .
Seite 8
Fron t LED - R E D Amplifie r is in Stan db y mod e, w ai tin g fo r a s i gna l t o p ow er up - GR EE N T h e amp lifie r is ON...
Practice of sound / Installation and placement tips The following points contains common information on loudspeaker placement and installation. These are general rules, so there are exceptions. How do i achieve No matter how good the equipment is, in the wrong listening environment it will inevitably sound bad. There are some basic rules concerning a proper loudspeaker installation: the best sound? Reflections...
Seite 10
Speaker To achieve the best results the front speakers should be placed symmetrically in front of the listener. The distance between the front speakers should be about 80% of the distance to the listener. In other words, the Placement recommended angle between the front speakers is 45°. Finally Please remember that good sound is a matter of taste, so you have to experiment to obtain your favorite one.
Operating EDGE A2-300 The EDGE A2-300 is designed to deliver high performance with easy management. Auto On When the unit is set to “Auto On” mode, the amplifier requires a constant signal to stay on. In absence of a signal the amplifier switches to standby mode in ~ 8 minutes.
Technical Specifications EDGE A2-300 Amplification type ICEpower - triple loop feedback CLASS D ® Power 2 x 460 W (1% THD, 2.7 Ω) 2 x 300 W (1% THD, 4 Ω) 2 x 150 W (1% THD, 8 Ω) 2 x 380 W (10% THD, 4 Ω) 2 x 190 W (10% THD, 8 Ω)
Accessories Short Left 19” Bracket EAN: 7340030420212 Article: 20057 Short Right 19” Bracket EAN: 7340030420229 Article: 20058 Middle 19” Bracket EAN: 7340030420236 Article: 20059 Long Right 19” Bracket EAN: 7340030420243 Article: 20060...
Seite 20
Inhaltsverzeichnis Praktische Hinweise zur Akustik Einführung Betriebshinweise EDGE A2-300 Sicherheitshinweise Anschluss der Lautsprecher Quick Setup Bi-amping Positionierung Stromanschluss (220V / 110V) 19” rack mounting Verbindungen (Störungsquellen) 23 Technische Spezifikationen Eingänge & Ausgänge XTZ Philosophie Unser grundlegendes Ziel ist die natürliche und harmonische Ton-Wiedergabe mit optimalem Verhältnis aus Preis, Leistung und Qualität.
• Verwenden Sie keine chemischen Lösungen zur Reinigung der Geräte. Benutzen Sie ein sauberes, trockenes Tuch. • XTZ kann für Schäden, die aus Nichtbeachtung der folgenden Punkte resultieren, nicht haftbar gemacht werden. • Bei starken Temperaturschwankungen kann es zu Kon- dens-niederschlag (Wassertropfen) im Inneren der Lautspre- •...
INPUT (Eingang) auf der Rückseite des EDGE A2-300. 3 Stellen Sie den Lautstärkeregler des Vorverstärkers auf die kleinstmögliche Stufe. 4 Schließen Sie das Netzkabel zunächst an den Netzeingang des EDGE A2-300 und dann an die Netz- steckdose an. 5 Stellen Sie die Schalter der CONTROLS Sektion auf die gewünschten Einstellungen. Sofern das Gerät im AUTO ON Modus genutzt wird, erkennt es ein anliegendes Signal und schaltet sich automatisch ein.
Trademarks Die Marke ICEpower ist eine eingetragene Handelsmarke der ICEpower a/s XTZ ist eine Handelsmarke der XTZ Group AB Reinigung des Schalten Sie alle Komponenten Ihres Systems aus, wenn Sie eines der darin enthaltenen Geräte reinigen. Reinigen Sie die Oberflächen nur mit einem weichen Stofftuch.
Strom versorgung - Strom an s c hlu s s Stro man sch lu ss un d S i c her un gsf a ss ung . - Sic heru n g Nu r du rch e in e T 4A H 25 0V S i ch er ung e r set z en. - Ne tz sch a lte r Ha u p tsc ha lte r d es Ne t zt ei l s.
Praktische Hinweise zur Akustik Die folgenden Punkte enthalten hilfreiche Informationen zur Lautsprecherpositionierung und zur Raumakustik. Es handelt sich um allgemeine Regeln, daher kann es Ausnahmen davon geben. Wie erziele ich den Unabhängig davon, wie hochwertig das Equipment ist, kann es in der falschen Umgebung nicht sein gesamtes Potenzial abrufen.
Lautsprecher- Um den bestmöglichen Klang zu erzielen, sollten die Frontlautsprecher symmetrisch zur Hörposition aufgestellt werden. Der Abstand der Lautsprecher von der Hörposition (B) sollte in etwa so groß sein, wie der Abstand Positionierung der Lautsprecher voneinander (A). Wird A gegenüber B zu klein, verringert sich die breite der Stereobühne deutlich.
Betriebshinweise EDGE A2-300 Der EDGE A2-300 wurde konstruiert um höchste Leistungsfähigkeit mit intuitiver Bedienung zu vereinen. Auto On Wenn das Gerät im AUTO ON Modus betrieben wird, benötigt der Verstärker ein konstantes Signal um eingeschaltet zu bleiben. In Abwesenheit eines Signals versetzt sich das Gerät in den Standby-Modus nach etwa acht Minuten.
Bi-Amping Warnung! Warnung! Die Verbindung zwis- Die Verbindung zwis- chen den Lautspre- chen den Lautspre- cherterminals muss cherterminals muss getrennt werden. getrennt werden. Audio-Quelle...
19” Rackmontage Um einen einzelnen EDGE A2-300 zu montieren benötigen Sie: • 1 kurzer linker Winkelträger • 1 langer rechter Winkelträger (Winkelträger sind optionales Zubehör)
Seite 33
Kurzer linker Winkelträger Langer rechter Winkelträger...
Seite 34
Um zwei EDGE A2-300 zu montieren, benötigen Sie: • 1 kurzer linker Winkelträger • 1 kurzer rechter Winkelträger • 1 mittlerer Winkelträger (Winkelträger sind optionales Zubehör)
Seite 35
Kurzer linker Winkelträger Kurzer rechter Winkelträger Mittlerer Winkelträger...
Technische Spezifikationen EDGE A2-300 Verstärkertyp ICEpower® - triple loop feedback CLASS D Leistung 2 x 460 W (1% THD, 2.7 Ω) 2 x 300 W (1% THD, 4 Ω) 2 x 150 W (1% THD, 8 Ω) 2 x 380 W (10% THD, 4 Ω) 2 x 190 W (10% THD, 8 Ω)
Seite 40
XTZ Group AB (Sweden) XTZ Deutschland (Germany) Gamla Nissastigen 17 Höhenstr. 7 31441 Torup / Sweden 75239 Eisingen / Deutschland Phone: +46(0)345-20049 Tel.: 072469131483 Mail: info@xtzsound.eu Mail: kontakt@xtz-deutschland.de...