Factory-Default Setting - CombiSteel 7455.1660 Gebrauchsanweisung

13. Stage Cooking Programming
This allows the user to cook food items at manual cook mode and programming mode.
1) Three stages can be set at most under cooking mode or programming mode. After setting the power and time
for the first stage, press " Time Entry " to set the second stage. And the same step to set the third stage.
2) When setting the second, third stage, press " Time Entry", "STAGE 2","STAGE 3" displays.
3) Press " " button to start cooking.
Example: In programming mode, press number buttons "3" to set two stages cooking. The first stage is PL 7 and
time is 1 minute 25 seconds. The second stage is PL5 and 5 minutes and 40 seconds. The steps are as follows:
a. Open the door, press number button "1" for 5 seconds, "PROGRAM" displays.
b. Press number button "3", the screen will display "P:03", after two seconds, the screen will display the related
time " :30".
c. Press "1","2","5" to input the cooking time. "1:25" displays.
d. Press "Med-Hi 70%", "1:25 70" displays. The first stage is finished.
e. Press " Time Entry", "STAGE 2" displays.
f. Press "5", "4","0" button, "5:40" displays.
g. Press "Medium 50%", "5:40 50 " displays. The second stage is finished.
h. Press " " button to start cooking.
i. The total time counts down.
14. Use Option Mode
This allows the user choose between various ways for the oven to operate.
1) Open the oven door and press "2" pad for 5 seconds. The buzzer sounds once and enters this mode.
2) The screen displays "OP: - -".
3) Press any number button to enter related mode setting. For example: to set the voice of the buzzer to medium.
Press " 2 ", "OP:22" displays. If you want to change, keep pressing "2", displays "OP:20", "OP:21","OP:22",
"OP:23", "OP:20" .....in cycle.
4) Press " " to save the current setting. After saved, "OP: - -" display again.
5) During setting process, press " " to enter Door Open Mode. Close the door will enter Ready Mode.
6) If " " button not pressed at the last step, the program cannot be saved but stay at previous way.
15. Service Mode
1) Open the oven door and press "3" pad for 5 seconds to enter service mode.
2) The screen displays "SERVICE".
3) To check the times of closing or opening the door, just press number button "3", the screen will display the
times.
4) Press " 1 " pad for Tube Hours.
Press " 2 " pad for Tube Cycles.
Press " 3 " pad for Door Cycles..
Press " 4 " pad to Clear service information.
Only for some models:
Press " 5 " pad to run Top Mag. Oven displays amps.
Press " 6 " pad to run Bottom Mag. Oven displays amps.
5) Press " " to enter Door Open Mode. Close the door will enter Ready Mode.

16. Factory-default setting

In the Ready Mode, pressing "
1) Press " " and " 0 ", the buzzer sounds once, and the screen will display "CHECK". If it is factory-default
setting, will display 11 ,after three seconds, the oven turn to the ready mode Press"
and back to ready back in the process of display. If not in the factory-default setting, the screen will display "00",
press " " to the factory-default setting, the screen will display "11" or"00".
2) Do not press " " when the display " 00 ",the setting will cancel.
Note: Be careful in the operation as it will restore all configure to factory-default setting.
" and " 0 " to factory-default setting.
www.combisteel.com
". to cancel the display
13