Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Receiver module
for energy harvesting wireless switches (AFZE)
QUICK START GUIDE
1 Safety guidelines
WARNING: Danger to life
Do not install this product as part of a
safety-relevant, life or health preserving
facility.
Observe the ESD protection.
Prevent liquid from getting inside the
components.
•
Do not use solvents such as benzine or alcohol,
or scouring agent and scourers for cleaning.
2 Area of application
The receiver module for energy harvesting wireless
switches (AFZE) was designed to demonstrate further
application options of the energy harvesting wireless
switch to you.
This quick start guide only covers the basic features of
the AFZE. You can obtain more detailed information in
the operating manual.
3 Starting up
3.1 Mounting the antenna sleeve
The AFZE has a fitted wire antenna. You need to mount
the antenna sleeve for protection and a straight
alignment.
1 Guide the wire antenna straight into the antenna
sleeve.
2 Insert the antenna sleeve into the holder horizontally
and turn it 90 degrees to the left.
The antenna sleeve is mounted.
Revision V03, DE, US, Aug 2017 (KA Empfänger-Modul, AFZE)
3.2 Connecting the power supply
The power is supplied using a USB micro-B plug
which can be connected via a computer or a power
supply unit.
4 Pairing and removing the
transmitter
You can pair 32 transmitters. On the AFZE there are
two buttons with LEDs on the left at the top in a
recess. Press the buttons with a sharp object such as
a ball-point pen.
Reset,
Pairing,
green LED
yellow LED
•
Connect the AFZE to the power supply. The lef
LED flashes green (if a transmitter has not yet
been paired) or lights up green (if a transmitter
has already been paired).
4.1 Pairing a transmitter (Pairing)
Get the transmitter that you want to pair ready. If
you do not touch anything more for than 2 minutes
during the procedure, it stops automatically.
1 Press the right button for 2 seconds (Pairing)
until the right LED flashes yellow.
2 Trigger a signal on the transmitter.
3 Press the right button briefly (Pairing).
The left LED lights up green and the right LED is
off. The transmitter is now paired.
If you trigger the transmitter, the right LED
flashes yellow with each signal and you will hear
the switching noise of the AFZE's relay.
4.2 Deleting the transmitter (Reset)
1 Press the right button (Pairing) and hold it down.
2 Press the left button briefly (Reset) while also
holding down the right button (Pairing).
3 When the right LED starts flashing slowly and
then flashes faster after 4 seconds, release the
right button (Pairing).
The left LED flashes green. All transmitters are
deleted.
5 Technical data
Name
Value
Antenna
External wire antenna
Frequency EU
868.3 MHz (± 15 kHz)
Frequency USA,
915.0 MHz (± 15 kHz)
Canada
Data rate
76.9 kBit/s
Name
Value
Interfaces
USB Micro-B, RS-485,
RS-232, RS-232 TTL,
Niederspannungsrelais
48 V/230 V
Wireless log
ZF Proprietär 2.0
Modulation
2-FSK
Coding
NRZ
Wireless channels
1
Range
300 m outdoors, 30 m
indoors
Operating temperature
–40 °C ... +85 °C
Sensitivity at 23 °C
–98 dBm at 0.1% telegram
error rate
Supply voltage
5.0 VDC ±5 % / 0.5 A (USB)
and / or
7 to 24 VDC / 3 W (power
supply connection)
6 Contact
Europe:
ZF Friedrichshafen AG
Electronic Systems
Cherrystraße
91275 Auerbach
Internet: www.switches-sensors.zf.com
E-Mail: switches-sensors@zf.com
North America:
ZF Electronic Systems
Pleasant Prairie LLC
11200 88th Avenue
Pleasant Prairie, WI 53158
USA
Asia-Pacific:
ZF Electronics Asia Limited
2/F Technology Plaza
29-35 Sha Tsui Road
Tsuen Wan, New Territories
Hong Kong
Internet: switches-sensors.zf.com
E-Mail: switches-sensors@zf.com
7 General user information
We reserve the right to make technical modifications which
serve the development of our products. Improper use and
storage can lead to faults and damage to the product.
The warranty expires completely once unauthorized
modifications to the product have been carried out. Do not
carry out any unauthorized repairs and do not open up the
product. These instructions are only valid for the supplied
product.
The warranty for this product is for commercial customers for
one year from date of purchase. Liability for financial damages
and defects is excluded.
8 Declaration of conformity
These components are CE certified and
comply with the guidelines EN 300-220 SRD,
EN 301-489-1/-3 and EN 60950-1. They
were made and tested for use in Europe and
USA in accordance with the FCC Part 15.249 and 15B.
Observe the local regulations before using in other countries.
9 Disposal
Dispose oft he used components at an official
Werbung
