Collingwood Lighting WC2820WH Anweisungen

WALL MOUNTED REMOTE CONTROL | TÉLÉCOMMANDE MURALE |
GLAS TOUCHPANEL
Instructions / Anleitung
ZONE NUMBERS
SAVED POSITION NUMBERS
ON/OFF ALL ZONES
INCREASE/DECREASE
MAX BRIGHTNESS
SAVE
COLOUR WHEEL
220/240V AC, 50/60 Hz
24V INPUT
LEARNING SWITCH
t +44 (0) 1604 495 151 f +44 (0) 1604 495 095
EN
e sales@collingwoodgroup.com w collingwoodlighting.com
Collingwood Lighting WC2820WH / 5055351501428
LED INDICATOR
START/STOP CYCLE
INCREASE/DECREASE CYCLE SPEED
RED/GREEN/BLUE/WHITE ON/OFF
DIM UP/DOWN
SEPARATE FRONT PLATE FROM BACK
PLATE HERE
CWL 2409 V1
PRI:
Uin=24VDC
lin=4A
Learning
Switch SEC:
Uout=4x(24)VDC
Iout=4x1A
TEMP RANGE:-20°C-+50C
0.5-2.5mm 2
6-7mm
xxxxxx
t +33 (0) 4 816 816 10 f +33 (0) 4 816 816 11
FR
e ventes@collingwoodgroup.com w collingwoodlighting.com
EN
This unit requires 220-240V AC 50/60 Hz mains power and fits a standard single pattress box of minimum 25mm depth.
1. Separate the front plate from the back plate by levering them apart with a small flat screwdriver (see illustration).
2. Connect the live and neutral mains power to the back plate terminals. No earth is needed.
3. Fix the back plate to the pattress box.
4. Carefully line up the connector pins, then push the front plate on to the back plate until it clips into place.
5. Switch on the mains power.
An LED indicator is above the colour wheel. Blue = on, red = standby. If on red, press the ON/OFF button before any other
operation, and the LED will change to blue.
Up to 8 wall mounted remote controls can be set to operate a C100924 controller. A wall mounted remote control will not operate
a controller until they are set up as a pair.
SET UP FOR SINGLE ZONE OPERATION
1. Switch on the power to the controller and power repeaters.
2. Remove the terminal cover from the C100924 controller to access the learning switch (next to the 24V DC input).
3. Press the learning switch on the controller.
4. Press 1 on the remote control to allocate Zone 1.
5. Run a finger around the colour wheel until the LEDs start to change colour.
6. The wall mounted remote control can now be used to change colours, select cycles etc.
NOTE – If the set up does not work first time, repeat steps 3, 4, and 5.
SET UP – Multiple Zones (up to 4)
To set a controller to Zone 2, follow the above process, but press 2 in step 4.
To set a controller to Zone 3 or 4, follow the above process, but press the appropriate zone number in step 4.
To delete a Zone setting, e.g. so it can be re-set to another zone, press the learning switch until the LEDs flash (approximately 5
seconds).
OPERATION
ZONE NUMBERS: Press 1 to select Zone 1, and the remote control will operate all LEDs in Zone 1.
Similarly, press 2 for to operate LEDs in Zone 2 etc.
Press and hold 1 to switch off LEDs in Zone 1. Press and hold to switch on.
Similarly for Zones 2-4.
OPTIONS
For all operation options, select the Zone number first, then the following operations will be actioned in that zone.
RGBW: Press R to switch on red LEDs. Press again to switch off red LEDs. Press and hold dims LEDs up/down.
Operation method for blue, green and white is the same.
Note – if for example red LEDs are on and blue is switched on, the output colour will be purple. To go from red to blue,
switch off red, then switch on blue.
White can be used in a colour mix to achieve pastel colours. For vivid colour mix, switch off or dim white.
COLOUR WHEEL: Touch to activate colour.
CYCLE: There are ten pre-set cycles. Press the start/stop cycle button to activate a cycle, press again to stop the cycle, press
again to go to cycle 2, etc.
Press and hold the button to increase/decrease cycle speed.
ON/OFF: Press to switch ON/OFF all zones.
INCREASE/DECREASE MAX BRIGHTNESS: A maximum brightness level can be set, e.g. if 50% is set, LEDs will not exceed 50%
brightness. Press and hold to increase/decrease maximum brightness.
SAVE: To save a colour or cycle in Zone 1, press 1, then the colour or cycle required.
Press and hold the save button until the LED indicator shows blue. Immediately press 1.
The LEDs will flash to confirm a successful save.
The colour or cycle is saved in Zone 1, position 1.
To recall the colour/cycle, press 1 (to select zone), press S (to access the saved ones) then 1.
Save up to 4 colours or cycles in each Zone.
t +49 (0)89 411123 777 f +49 (0)89 411123 778
DE
e verkauf@collingwoodgroup.com w collingwoodlighting.com
CWI 8077 V1