FireClass FC430SAM Schnellstartanleitung Seite 2

1. INTRODUCTION
The Sounder Base Ad dress Mod ules (FC430SAM/FC430SAB) are de signed to
con trol a loop pow ered sounder base for use with the FCsystem, one vari ant
(FC430SAB) has an in te gral bea con. They may also be used to drive a re lay base.
The units are used to sup ply the ad dress de cod ing in place of a de tec tor, thus pro -
vid ing a loop pow ered sounder when used in con junc tion with an FC430SAB. The
mod ules are col our matched to the sounder bases. The FC430SAM/FC430SAB is
locked into the base us ing the lock ing de vice in te gral to the sounder base.
Note: To en su re that the so un der base me ets the Access re qui re ments of
EN54-3, the SAM/SAB must be se cu red to the so un der base by a loc king pin at -
ta ched to the 5" Uni ver sle Base.
1.1 FC430SAM
The FC430SAM is suit able for wall or ceil ing mount ing as stan dard, but it has no in -
te gral LED or re mote LED drive.
1.2 FC430SAB
The FC430SAB Sounder Ad dress able Bea con has a flash ing bea con in cor po -
rated into the front with a red lens ar range ment. It is de signed for wall mount ing ei -
ther on a sounder base or on a con ven tional base. When mounted 2 to 2.2m above
ground level the bea con pro vides a high uni form in ten sity wide an gle light out put.
The base ori en ta tion is not crit i cal to the view ing of the SAB bea con.
2. TECHNICAL SPECIFICATION
2.1 MECHANICAL
:
Di men sions
Ma te ri als
Body,cover, and clo sure:
Weight
FC430SAM:
FC430SAB:
2.2 ENVIRONMENTAL
Tem per a ture
Op er at ing Tem per a ture:
Stor age Tem per a ture:
Rel a tive Hu mid ity:
:
Pres sure
:
Vi bra tion
:
Cor ro sion
2.3 ELECTRICAL CHARACTERISTICS
Sup ply Volt age
Ad dress able loop volt age:
Cur rent Con sump tion
:
Stand-by
FC430SAB:
FC430SAM:
There is no ad di tional cur rent surge when FC430SAB goes be tween non-flash ing
and flash ing states.
Elec tro mag netic Com pat i bil ity
The FC430SAM/FC430SAB com ply with the fol low ing:
Prod uct fam ily stan dard EN50130-4 in re spect of Con ducted Dis tur bances, Ra di -
ated Im mu nity, Elec tro static Dis charge, Fast Tran sients and Slow High En ergy;
EN61000-6-3 for Emis sions.
Each of the FC430SAM/FC430SAB and so un der cir cu its are po we red using po -
wer sup plied from the FC Di gi tal de tec tion loop, via the L (-ve) and L1 (+ve) ter mi -
nals. The L2 ter mi nal is used to pro vi de the con trol si gnals from the FC430SAM or
FC430SAB to the So un der Base.
The over all di men sions are shown in
Fig.3 and 4.
FR110 'BAYBLEND' flame re tar dant.
0.068kg
0.070kg
o o
-10 C to +55 C
o o
-25 C to +70 C
Up to 96% RH (non-con dens ing)
(Not pres sure sen si tive but Sounder
out put is quoted for at mo spheric pres -
sure of 1000mBar).
De signed to meet the re quire ments of
EN 54-3.
The sounder ad dress mod ules pass the
SO cor ro sion test from EN 54-3.
2
20V - 40V dc po lar ity con scious
250µA typ i cal
3.25mA flash ing or con tin u ous
250µA (+ as so ci ated Sounder/Re lay
cur rent)
ENGLISH
3. MECHANICAL CONSTRUCTION
3.1 OVERALL
The FC430SAM mo du les uti li se the exi sting FC de tec tor body mo ul ding with a si -
mi lar PCB and PCB mo un ting ar ran ge ment uti li sing the same de tec tor ter mi nals
and sur fa ce mo unt PCB con tact clips as the FC Di gi tal de tec tors. The co ver is of a
low pro fi le de sign, but re ta ins the same ove rall fa mily ap pe a ran ce.
4. OPERATION
Com mu ni ca tions bet we en the con trol ler and de tec tor uses the Fre quency Shift
Ke ying ( FSK ) met hod. The 'Di scri mi na tion Cir cu it' fil ters the FSK si gnal from the
+ve line vol ta ge and con verts it to a di gi tal squa re wave in put for the 'Com mu ni ca -
tions ASIC'. The 'Com mu ni ca tions ASIC' de co des the si gnal and when its own ad -
dress is de co ded, when re qui red, dri ves the fun ctio nal base in ter fa ce cir cu it and/or
the be a con con trol line via the con stant cur rent so ur ce.
5. OPTICAL
5.1 FLASHER OPTIONS
With the FC430SAB, two fla sher op tions are made ava i la ble.
Con ti nu o usly on.
1 Hz flash (FC430SAB) - Free run ning, no synchro ni sa tion bet we en fla sher units.
The se op tions may be se lec ted in Fire Class 500.
5.2 FLASHER TIMING
The fla sher is set so that it ap pe ars to pul se at a rate of 1 pul se every se cond
FC430SAB. This is achie ved by using a short du ra tion high cur rent pul se to in cre a -
se the ap pa rent in ten sity, whilst en su ring that cur rent le vels are ma na ge a ble.
6. SAM/SAB ADDRESS
The loop ad dress of the FC430SAM/FC430SAB is held in in ter nal E
pro gram med from the FC490ST Loop Ser vi ce Tool.
7. ADDRESS FLAG
Re fer to Fig.6 .The ad dress flag is used to iden tify the ad dress and zone of the base. The
ad dress flags are sup plied in one of two packs (ad dress 1 - 127 or 128 - 255, with a dif fe -
rent co lo ur for each loop) and are or de red se pa ra tely from the FC430SAM/FC430SAB.
The ad dress flag is fit ted to the bot tom of the FC430SAM/FC430SAB. When the
FC430SAM/FC430SAB is fit ted to the base and tur ned un til fully lo ca ted the ad dress flag
is then tran sfer red to the base. If the FC430SAM/FC430SAB is re mo ved from the base,
the ad dress flag re ma ins with the base.
8. FIRECLASS 500 CONSOLE CONFIGURATION
The FC430SAM and FC430SAB de vi ces are ava i la ble as de vi ces on Fi re class di -
gi tal lo ops. The con fi gu ra tion of a fun ctio nal base, both so un der or re lay, is ava i la -
ble from the page con fi gu ra tion po int. It is pos si ble to use the FC430SAB with or
wit ho ut a fun ctio nal base.
9. ORDERING INFORMATION
FC430SAM So un der Address Mo du le.
FC430SAB So un der Address Be a con.
10. RECYCLING INFORMATION
Cus tom ers are rec om mended to dis pose of their used equipments (pan els, de tec -
tors, si rens, and other de vices) in an en vi ron men tally sound man ner. Po ten tial
meth ods in clude re use of parts or whole prod ucts and re cy cling of prod ucts, com -
po nents, and/or ma te ri als.
11. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
In the Eu ro pean Un ion, this la bel in di cates that this prod uct should
NOT be dis posed of with house hold waste. It should be de pos ited at an
ap pro pri ate fa cil ity to en able re cov ery and re cy cling.
The ma nu fac tu rer re ser ves the right to chan ge the tec hni cal spe ci fi ca tions of this
pro duct wit ho ut prior no ti ce.
2
PROM which is