Frog Avro Lancaster Kurzanleitung

5
6
19
18
2
25
ASSEMBLY INSTRUCTIONS
READ ALL THE INSTRUCTIONS
TO ASSEMBLE THE MODEL.
USE THE SPECIAL FROG
SUPPLIED FOR FIXING THE
USE IT VERY SPARINGLY
ANY ON THE OUTER SURFACES OF THE MODEL,
DO NOT LET IT TOUCH THE
First detach all the parts from the stalks, and lay them on the work
table, to identify them with the sectioned drawing.
part fits before assembling, and trim off any surplus material if necessary.
This precision-moulded Model is made of high quality
Plastic, and care should be taken when cementing the parts together.
The Model is supplied with plug-in undercarriage legs which are nor-
mally cemented into place, but these can be omitted
undercarriage doors fitted in the closed position instead (when the model
is mounted on the stand).
First cement the fuselage halves ( l,) and (2) together after painting
the inside faces pale green.
2. Cement the wing halves (3) and (4), (5) and (6) together, holding
the parts with clothes pegs or spring clips.
fuselage in their respective slots.
3. Cement the tailplane halves (7) and (8) into the slots at the rear
of the fuselage, followed by the fins (9) and (10).
4. Assemble the four spinners (II)
bushes (12a) onto propeller shafts, and cement
these allowing sufficient clearance
these units into place when the nacelle halves ( 14) and (15), (16) and (17)
are cemented together, making sure the propellers run freely.
LANCASTER
1196th PLASTIC
9
24
PAINT TIPS YELLOW.
12
BEFORE STARTING
POLYSTYRENE CEMENT
PARTS TOGETHER.
AND AVOID GETTING
AND
EYES OR CLOTHING.
Make sure that each
if desired and the
Then assemble these to the
to propellers ( 12) then slide
collars ( 13) to the ends of
for the propellers to revolve.
AVRO
SCALE
23
8
22
TRANSFER.
14
3
28
26
PAINT
5. Assemble guns (18) into turret (19), (20) into (II)
(23); Cement these units to the fuselage, followed
front window (25).
Polystyrene 6. Cement wheel halves (26) and (27) together,
Fit wheels onto
legs silver as indicated on drawing.
with struts (29).
and cement them into
7. Cement tailwheel
PAINTING AND
8. The model should be painted camouflage brown and green on the
upper surfaces; refer to 3 view diagram for details of this. Use Frog Special
Plastic Enamel Paint or other good quality enamel.
sufficient if applied evenly using a soft brush.
Spirit if necessary. Do not use Cellulose paint, as this will attack the sur-
face Of Polystyrene, and leave a crackled finish.
9. Affix the transfers in place when the paint has dried, following the
instructions on the back.
damping to fix them.
Cement
10. Assemble the stand pillar into the base and affix the transfer in
place. The top of the pillar fits into the slot in the fuselage.
MODEL
CAT.
21
20
7
32
16
15
12
29
PAINT INSIDE
30 PALE GREEN
31
SILVER.
27 R.S.P.
undercarriage legs (28). Paint small area of undercarriage
Assemble undercarriage into nacelle
Then paint the inside of doors (30) and (31) pale green,
place.
(32) into hole at the end of the fuselage.
FINISHING.
They are waterslide
Separate each part first.
HEAVY
BOMBER
No. 359 P.
10
TRANSFER.
3
17
4
and (22) into
by the cabin (24) and
paint hubs silver.
One coat should be
It can be thinned with White
type, and only require