INDUSTEX Rotorazer 8 in 1 Bedienungsanleitung Seite 13

3. INSTRUCTIONS FOR USE
How to install batteries
Always be sure that the machine is switched off
before manipulating the battery.
Always hold the machine and the Battery firmly
when installing or removing them.
After charging the Battery (2) with the Charger (3)
for a minimum of 100 minutes, simply align the
Fast Mower by Rotorazer's battery terminals (at
the handle) to the grooves of the Battery. Slide the
Battery through all the way towards the machine
until a click sounds to lock (Image A).
How to remove batteries
Always be sure that the machine is switched off
before manipulating the battery.
Always hold the machine and the Battery firmly
when installing or removing them.
To remove the Battery (2), push down on the red
button of the Battery and pull out by sliding it off
away from the machine (Image B).
How to use
Assembling the Small Baffle
Use the Small Baffle (6) when you don't need to
use the wheels (12). Wheels can only be used with
the Big Baffle (5).
1- Unscrew and take out the top of the cover (13)
(Image C).
2- Align the Small Baffle (6) into the slots with the
same shapes (Image D) and press until the Small
Baffle enters completely into the cover.
3- Once fully entered, rotate the Small Baffle (6)
until the Small Baffle's circle hole stays at the top
(Image E).
4- Put back the top cover (13) over the plate (Image F).
5- To install the blades, please go to the "Assem-
bling Blades" section.
Assembling the Big Baffle & Wheels
Use the Big Baffle (5) when you need to use the wheels
(12). Wheels can only be used with the Big Baffle (5).
1- Unscrew and take out the top cover (13) (Image C).
2- Introduce the long screw on the external side of
each of the wheels (Image G).
3- Place the nut on the inner area of the Big Baffle
(5) and align the long screw of the wheel with it, and
screw them together with the help of the Wrench
(14) (Image H).
Note: There are three holes on each side of the
wheels: please choose the desired hole depending
on desired height for the wheels (Image I).
4- Once the wheels are assembled, align the Big
Baffle (5) into the slots with the same shapes and
press until the Big Baffle enters completely into the
cover. Once fully entered, rotate the Big Baffle (5)
until the circle hole stays at the top (Image J).
5- Place the screw (17), as shown in image U, and
screw it in with the screwdriver (16) so that both
parts are correctly fastened.
6- Put back the top cover (13) over the plate (Image K).
7- To install the blades, please go to the "Assem-
bling Blades" section.
Assembling Blades
All the blades can be assembled on both the Big
baffle (5) and Small baffle (6).
IRON BLADE (7):
Suitable for weeds in complex terrain.
Sizes: 15 x 3,3 cm
Cutting depth: 5 cm
PLASTIC BLADE (8):
Suitable for lawn mowing.
Sizes: 15 x 3,3 cm
Cutting depth: 5 cm
ROUND BLADE (9):
Suitable for cutting crops and shrubs.
Sizes: 15 cm dia.
Cutting depth: 5 cm
GRASS CUTTING ROPE (15)
Suitable for new growth & soft grass
Sizes: 15 x 3,3 cm
Cutting depth: 5 cm
PLASTIC BLADE
1- Align the Plastic blade (8) with the top cover's
hole, and place the screw above of it (Image L).
2- Hold the top cover by hand and tighten the screw
with the Nut driver (10) (Image M). To remove sim-
ply reverse the steps.
IRON BLADE
1- Align the Iron blade (7) with the top cover's hole,
and place the screw above it. Hold the top cover by
hand and tighten the screw with the Nut driver (10)
(Image N). To remove simply reverse the steps.
ROUND BLADE
1- Unscrew and take out the top cover (13) (Image C).
2- Align the Round Blade (9) with the top cover's
hole put the mark side facing yourself and place
the screw above it.
Hold the top cover by hand and tighten the screw
with the Nut driver (10) (Image O). To remove sim-
ply reverse the steps.
GRASS CUTTING ROPE
1- Unscrew and take out the top cover (13) (Image C).
13