Cerva OS HelmIQ Schnellstartanleitung

otto schachner nordic
Prinsessens Kvarter 2
DK-7000 Fredericia
www.osnordic.dk
(Declaration of Conformity)
PO:42405
GB - INSTRUCTIONS
This industrial and construction protective helmet, model HelmIQ is
subject to the conformity assessment procedure according to PPE
Regulation (EU) 2016/425 and the Standard EN 397:2012+A1:2012.
This safety helmet is made to absorb the energy of a blow by partial
destruction or damage to the shell and harness. Industrial safety helmet
is for general use in industry and construction, intended to offer protection
to the wearer against falling objects consequential brain-injury and skull
fracture.
Read and understand all warnings and information contained in these
instructions. Refer to these User Instructions before and after each use.
Please contact otto schachner nordic if you have any additional
questions regarding the safety and use of this equipment.
WARNINGS
• otto schachner nordic, its affiliates, subsidiaries, importers,
distributors, and dealers will accept no responsibility in the event of an
accident leading to injury or death and shall not be liable for any injury,
death, loss, or damage resulting from improper use of this helmet.
• This helmet is not designed to provide protection from the following
hazards:
Non-ionizing radiation, ionizing radiation, external radiation, or any
condition not expressly stated in this use information.
• This helmet has no electrical insulation rating. DO NOT USE THIS
HELMET IN AN ELECTRICAL HAZARDOUS ENVIRONMENT.
• Compatible components specific to this helmet and approved by the
manufacturer may be added if the safety functions are not compromised.
See the OBSOLESCENCE section for information on those topics.
• The helmet is designed to absorb shock by partial destruction of the
shell and harness. This damage may not be visible. If subject to severe
impact or deterioration, the helmet should be replaced and destroyed,
even if it is apparently undamaged.
• Safety intended to be provided by the helmet can only be ensured when
it is properly assembled and correctly fitted, and that removable parts
shall not be worn separately.
• Use this helmet exclusively for the activities for which it is certified and
in strict accordance with all applicable regulations under the authorities
having jurisdiction in the region where your work is performed.
• No helmet can protect the wearer against all possible impacts. For
maximum protection, the helmet must fit firmly on the head, and all
retention straps must be securely fastened.
• Most performance properties of these products cannot be tested by the
user in the field.
• There are innumerable wrong uses possible, it's not feasible to describe
them all.
• The helmet must be used exclusively in the applications mentioned by
the manufacturer as below.
FITTING & USE
Head sizes between 53- 63 cm will normally be adjustable by rotating the
nape ratchet.
Wearing height adjustment:
The wearing height can be adjusted vertically without removing the
harness from helmet shell follow below instruction:
1) There are 6 adjusting elements to adjust the wearing height, 2 at the
front left and right, 2 at the middle left and right and 2 at the back left and
right.
2) Twist the part A until it releases from the slot. Follow the wearing
height you need to change the slot location. i.e.: from upper to lower, or
from lower to upper. Finish the changes, push in the part A into the slot
and then twist the part A until it can lock safely. (See below picture)
Safety Helmet HelmIQ
Art. 24201010, White
Art. 24201021, Orange
Art. 24201030, Red
Art. 24201040, Blue
Art. 24201060, Yellow
Art. 24201061, Light Yellow
Art. 24201070, Black
Accessories:
Art. 2420001, Visor, Clear PC
Art. 2420002, Visor, Grey PC
Art. 2420003, Reflective labels
Art. 2420004, Chin Strap
Art. 2420005, Sweat Band
The integrity, fit, and proper assembly of the helmet, suspension, and
chinstrap must be checked before each use. Your safety depends upon
the proper fit of your helmet and proper use of all features and
components.
The system included in the harness, plastic cradle straps, chin straps
shall be adjusted so that the helmet perfectly fits the user's head, The
helmet is made to absorb the energy of a blow by partial destruction or
damage to the shell and the harness, and even though such damage may
not be readily apparent, any helmet subjected to severe impact should
be replaced.
HOW TO WEAR & ADJUST IT
Adjusting the Size to Fit Your Head:
Ratchet Adjustment: Rotate clockwise the ratchet control knob on the
back of the helmet for contract and rotate anticlockwise the ratchet
control knob for expand. Make sure the nape strap provides comfortable
fit but not over tighten. A correctly adjusted headband should fit the user's
head securely before adjusting the chinstrap.
Adjusting the Chinstrap:
Insert the buckle into the mating clip until both 'snaps' together with a
'clicking' sound. Pull the free strap at the buckle end to desired tightness.
This is 4-point chinstraps there are 2 nape adjustment strap buckles that
need to be tightened.
SERVICE AND MAINTENANCE
This section identifies the best practices you should use to clean, prevent
damage, prolong the life and maintain high safety standards for your
helmet. Clean and disinfect the safety helmet shell and suspension follow
below CLEANING AND DISINFECTION instruction. Do not use paints
(unless approved in writing by otto schachner Nordic), solvents,
chemicals, adhesives, gasoline or like substances on this helmet. Such
substances may destroy the impact resistance and other protective
properties of the helmet without being apparent or readily detectable by
the user.
CLEANING AND DISINFECTION
Clean and disinfect the protective helmet after each use or whenever the
helmet has become soiled. You may clean and disinfect the helmet with
or without the components.
Choose a utility sink that is specifically used for cleaning and disinfection
the protective helmet; do not use a kitchen sink or other sink used for
personal products.
Loosen the nape strap and chinstraps, cleaning and disinfection using
the instructions provided below.
» Brush off any loose debris.
» Fill the utility sink with warm water no hotter than 40℃.
» Use only mild detergents in the recommended amount on product.
» Scrub the exterior of the helmet gently using a soft bristle brush.
» Inspect the helmet and, where necessary, rewash any portions of the
helmet that do not appear clean, or contact manufacturer for more
information.
» Dry the helmet by air drying it in a well-ventilated area, but not in direct
sunlight. Do not force dry the helmet with a hair dryer or place it over a
heating duct or radiator. Forced drying may cause damage to the helmet
suspension.
DECONTAMINATION
Proper decontamination of your protective helmet will depend on the type
and extent of contamination. If your protective helmet has become
contaminated with blood, body fluids, chemicals, or other hazardous
substances, immediately isolate your helmet and remove it from service,
taking care not to cross-contaminate other clothing items. Immediately
inform your supervisor, department, or organization. Do not wear a
helmet that was contaminated until verification has been provided, that it
is free from contamination.
STORAGE
Use the rear storage hook (where fitted) and if possible, store out of direct
sunlight especially behind glass or in vehicles during high summer
temperatures.
Store the helmet in a clean and dry place at a normal room temperature,
in an uncontaminated area where it is no going to be damaged. When
not in use or during transportation, this helmet should be stored in an
1/10