klemko HB-PIR-UNI 15M Handbuch

EN
Klemko Techniek B.V. Nieuwegracht 26
Specifications
MANUAL
870464 - HB-PIR-UNI 15M
NOTE: isolate all connection cables
before installation.
Read the instructions for use.
If in doubt, consult a qualified installer!
PROTECTION
• Electrical equipment must be
installed and fitted by a qualified
installer.
• Contact an installer in the event of
faults or defects.
• A fuse (250VAC, 16A) type B ac-
cording to EN60898-1 for load 1 (↑)
should already have been installed
in the installation.
Fuse
Introduction
The HB-PIR-UNI 15M can be used to
switch and control lighting in corridors,
warehouses and other high-ceilinged
USING FOR THE FIRST TIME
areas.
It takes around 60 seconds before the
sensor is fully operational.
The detector has 1 relay output with a
switched phase with zero-crossing con-
troller that is resistant to high switch-on
currents.
A lens mask has been supplied to mask
An external switch block is used. The
the detection zone.
connections and other electronics are
The lens mask has two layers and each
integrated in the sensor head.
layer has a number of sections. Each sec-
tion masks part of the detection zone.
The detection range is a circular area
max. 20 metres in diameter. The inner
core of this area is highly sensitive and
the outer edge has a lower sensitivity
level (bigger movements).
The time and lux threshold settings of the
sensor can be configured as required.
The lux setting can also be automatically
taught in between 10 and 500 lux.
Guarantee: 24 months after production date provided the product is used as instructed and the housing has not been opened.
T +31 (0)88 002 3300
CHOOSING A POSITION
De maximum installation height is 15
Mains voltage 220 - 240 V 50/60Hz
metres. If the sensor is higher, the detec-
Contact NO contact, 10A
tion sensitivity will be reduced.
Zero crossing Yes
The range extends up to a maximum
Load (lighting):
range of 20 metres in diameter (PIR).
Max. 800 VA / 720 W / 27 drivers
LED with driver Determine the location where the
(f pf = 0.9, NOTE: Max. switch-on current)
detector is to be installed, bearing the
Max. 800 VA / 720 W / 25 lamp.
Retrofit LED
(f pf = 0.9, NOTE: Max. switch-on current)
following in mind:
High-voltage halogen Max. 2000 W 1. Air vents: look out for discharge from extractor
Low-voltage halogen Max. 1200VA / 1000 W
2. Objects that could be moved by air currents such as
Incandescent lamps 2000 W AC
3. Do not point the sensor at other light sources.
4. Do not aim the sensor at highly reflective surfaces
HF fluorescent
Max. 800 VA / 600 W
(uncompensated)
HF fluorescent
Max. 1200 VA / 140 μF
5. Consider the approach direction (always try to
(compensated)
Energy-saving lamps Max. 800 VA / 600 W
Other specifications:
6. Do not install the detector on conducting
Detection range 12 metres: Φ20m / 360°
Time setting Pulse, 30 sec - 30 min
10 - ∞ ☼
Lux setting adjustable
When the detection fields are crossed
Temperature -20° C to +45° C
Approx. 20 m at 15 m height, 20 °C.
IP20 when flush-mounted
IP value
When the sensor is approached head-
IP54 with surface-mount housing
on Approx. 8 m at 15 m height, 20 °C.
Own consumption < 0.5 W
Remote control Optional, 870466
Standards CE/TUV
16A IEC/EN 60898 certified,
Type B
flush-mounted: Ø 68
Dimensions
external diameter: 105 mm
LENS MASK
OPTIONAL PULSE SWITCH
An external pushbutton is optionally
available to operate the sensor manually.
Press the button once briefly to switch on
the load. Press the button again briefly to
switch it off.
The lighting will remain on for as long as
presence is detected including the set
NOTE: The lens mask masks the
switch-off delay.
indicated detection range.
NL-3763 LB Soest www.klemko.nl
The springs supplied separately can be
used to install the sensor in a suspended
ceiling.
1.
2.
hoods, heating vents, tumble driers, etc.
3.
plants and curtains.
4.
such as swimming pools (because of rapid tempera-
ture changes)
5.
position the field in such a way that someone
approaching crosses the field instead of moving
straight towards the sensor).
Non-dropping screw
surfaces.
DETECTION RANGE
H 12 m
15m
The sensor can be surface-mounted us-
ing the supplied surface-mount housing.
1.
2.
3.
4.
5.
The Netherlands info@klemko.nl
INSTALLATION
Ceiling flush-mounted
Drill a Ø68 mm hole in the ceiling
board, which should be between 5
and 25 mm thick.
Leave the phase, neutral and switch
wire hanging out of the hole.
Strip between 6 and 8 mm off the
cores.
Connect the wires up to the right
connections
Locate the sensor in the hole and
secure in place using the springs.
68
Distribution junction box mounting
If permitted by the distribution junction box, the
sensor can be installed in the junction box itself
using the distribution junction box adapter.
1. Leave the phase, neutral and switch
wire hanging out of the junction
box.
2. Fit the mounting plate.
3. Strip between 6 and 8 mm off the
cores.
Surface-mounting
4. Connect the wires up to the right
connections.
5. Place the sensor on the mounting
plate.
If necessary, snip the cut-outs for
the wires out of the surface-mount
housing.
Mount the housing on the surface.
Strip between 6 and 8 mm off the
cores.
Connect the wires up to the right
connections
Mount the sensor on the sur-
face-mount housing.
Non-dropping
Non-drop-
screw
ping screw
Distribution
junction box
adapter
V1911