RHEINTACHO RT STROBE 3000 Bedienungsanleitung Seite 2

These operating instructions form part of the appliance. They
must be kept ready to hand and passed on to subsequent users.
Ask your supplier if you do not understand something. The
manufacturer reserves the right to make further improvements
to this appliance without documenting this in every case. Your
supplier will be happy to give you information on how up-to-
date these operating instructions are.
1. Proper use
This appliance is used for checking the movement of rotating and
vibrating objects. It must only be used in accordance with these
operating instructions. The appliance must not be altered in any way.
The manufacturer will not be liable for any damage resulting from
incorrect or improper use. This will also render the guarantee null
and void.
2. Safety information
 CAUTION HIGH VOLTAGE! The appliance must not be opened,
except to replace the flashbulb (see Section 5).
 WARNING! Under strobe lighting, moving objects appear stationary
or in slow motion. The objects should never be touched.
 WARNING! The appliance must not be used in explosion hazard
areas.
WARNING! Store the appliance in a dry place. It must not be

exposed to water (dripping or splashing). No objects filled with liquids
(e.g. vases) should be placed on the appliance.
 WARNING! Strobe lighting can trigger epileptic fits in those who are
susceptible.
CAUTION! Repairs to the stroboscope should only be carried out by
the manufacturer or supplier.
CAUTION! The stroboscope's electronic components and the flash
tubes contain environmentally harmful substances. They must be
disposed of in accordance with the relevant national environmental
guidelines.
CAUTION! While operating the appliance with the front screen
facing upwards, the screen can heat up.
3. Assembly and connection
Point the stroboscope at the object to be observed. On the bottom of
the stroboscope are 3 threaded holes, which allow you to fix it to the
equipment to be observed or a stand (available as an option):
• Centre = 1 x 1/4" threaded hole
• Right and left, with a total distance of
60mm = 2 x M5 threaded holes
The stationary stroboscope has two identical assigned sockets for the
combined input of trigger signal and supply voltage. The assignment
of plug contacts is shown in (Fig. 1).
CAUTION! Please make the connections in accordance with the
wiring diagram (Fig. 1). The trigger input is potential-free. The
potential-free input is suitable for PNP and NPN signals. A matching
plug for these input sockets is included with the appliance.
 RECOMMENDATION! Use a shielded cable to connect the trigger
signal.
CAUTION! Do not trigger the appliance with signals above 12,500 FPM.
Typical connection examples:
Please take connection examples from Figures 2 to 5. Please note
that you will need optional accessories for some of the examples
(stationary stroboscope, AC Adapter, sensor)
a) Trigger signal and supply voltage from external equipment (Fig. 2)
b) Trigger signal from external equipment (Fig. 3),
supply voltage from optional AC Adapter
c) Trigger signal from optional sensor (Fig. 4), supply voltage
for appliance and sensor from optional AC Adapter
d) Trigger signal from optional stroboscope control unit,
supply voltage from optional AC Adapter (Fig. 5)
The voltage is either supplied by the appliance power supply unit
(available as an option) or the equipment being observed.
The appliance requires an external trigger source. Possible trigger
sources include a stroboscope control unit, an external machine or
a sensor.
NOTE! When using the stationary stroboscope without stroboscope

control unit, the stroboscope flashes with the trigger signal of the
connected equipment. This signal cannot be influenced without a
stroboscope control unit.
4. Operation
• Point the stationary stroboscope at a moving object and switch
it on. The red LED indicates that it is ready for use.
• As soon as the trigger signal is applied, the appliance will
start to flash with the trigger frequency.
• If the flashing frequency coincides with the movement frequency,
a stationary image will appear.
PLEASE NOTE: A stationary image will not only appear with an

identical flashing frequency, but also with multiples and fractions
thereof.
5. Replacing the flashbulb

CAUTION HIGH VOLTAGE! CAUTION!
• Only use the original flashbulbs from the manufacturer.
• Never the touch the flashbulb with your bare hand.
• Ensure that the flashbulb is correctly positioned in the socket.
If it is not, this will reduce the luminous efficiency of the reflector.
• Never operate the appliance without a front screen or
with a defective front screen.
Operational steps:
• Switch off appliance and remove the power supply plug.
• Loosen T10-TORX screws on the front side of the appliance
with the safety labels.
• Pull front screen out laterally.
• Remove old flashbulb.
• Pick up new flashbulb with a clean cloth (free of dust and
grease) and insert in socket with the mark facing up.
• Insert front screen.
6. Equipment supplied
• stationary stroboscope
• Operating instructions
• (1) connector for trigger input and supply
7. Accessories, optional
• Spare flashbulb
• Stand/wall mount
• AC Adapter
• Connector for trigger signal/supply connection
• Connecting cable with plug for connection to the
stationary stroboscope, with open cable for connection
to external equipment.
• stroboscope control unit, handheld device for stroboscope
control and regulation.
Figure 1
1
4 2
1 +24V
1
2 ID-Pin
3 GND
4 +Trigger
5 -Trigger
DIN 41 524
(EN 60130-9)
1 +24V
2 ID-Pin
3 GND
4 +Trigger
5 -Trigger
1 2 3 4 5
Plug
Figure 2
2
1
+24V
3
GND
4
+Trigger
5
- Trigger
Machine Plug
Figure 3
3
1
+24V
3
GND
AC Adapter Plug
4
+ Trigger
5
- Trigger
Machine Plug
Figure 4
4
1
+24V
3
GND
AC Adapter Plug
1
+24V
4
5
- Trigg.
3
GND
Sensor Plug
Figure 5
Printed CE-Conformity on request
We reserve the right to make technical changes without
prior notice. We have taken the utmost care to prevent errors.
Liability in the event of any errors shall be excluded.
8. Technical Data
5
General Parameters
Range
3
Power Input
External Trigger Input
Flash Tube Parameters
Lifetime
Flash Duration
Light Emission flash
Light Emission
Illumination area
Flash Colour
Flash Energy
1 2 3 4 5
Plug
Housing
Material
Size
Weight
Ambient Conditions
Ambient Temp
Storage Temp
Humidity
Certifications
Operating Instructions
Stationary stroboscope
for industrial use
5
1
+24V
3
GND
AC Adapter Plug
1
+24V
4
+ Trigger
5
- Trigger
2
ID-Pin
3
GND
StroboControl Plug
0...12,500 FPM (flashes per minute)
15...28 V DC / 12 W
DIN 41524 5pin standard connector
Universal power supply available
3...30 V / max. 2 mA (potential free
optocoupler)
DIN 41524 5pin standard connector
Uout = 24 V max. 200 mA
> 200,000,000 flashes (@ 6,000 FPM)
< 5 µs
10 Mega-Lux / 30 cm / 12"
500 Lux / 30 cm / 12" (@ 6,000 FPM)
20x30 cm
6,000...6,500 K
600 mJ @ ≤ 1,200 FPM
Aluminium
150x130x112 mm / 6.0x5.1x4.4 inch
870 g
0°...40° C (32°...104° F)
-25°...70° C (-13°...158° F)
Max. 95 % not condensed
EMV / EMC 2004/108/EC
EN 61010:2001
2006/95/EC