Bailey 139851 Handbuch
Verfügbare Sprachen
Verfügbare Sprachen
Quicklinks
LED Wallpack
Manual - Handleiding
Bedienungsanleitung - Manuel d'instruction
Technical Specifications
Operating voltage / Nom. spanning / Betriebsspannung / Tension nominale
Beam angle / Stralingshoek / Abstrahlwinkel / Angle de diffusion
Operating temperature / Omgevingstemperatuur / Betriebstemperatur / Température ambiante
IP Rating / IP Waarde / Schutzart / Protection IP
B
A
A
B
A – Tapped holes with metal screw cap suitable for TP Watertight connector (Included)
B – Mounting holes
EN
Caution
•
Disconnect power before installation and servicing.
•
Make sure the supply voltage is the same as the rated luminaire voltage.
•
The product may only be assembled and fitted by a qualified electrician.
•
Mounting surface must be specified to properly support the weight of the luminaire.
•
Suitable for both internal and external use.
•
Suitable for wall mounting only.
Installation
1.
Switch off the power supply. Open the luminaire by removing the 2 screws on the side. Line up back plate and mark
mounting holes (B) onto surface. Mount securely (gaskets included) and ensure luminaire is installed tight to mounting
surface. Optional:
- Remove front cover by disconnecting connector
- Use metal bracket for wall mounting (included)
2.
Select a cable entry and remove the screw cap from the desired mounting hole (A), place watertight connector (included)
and connect power cable to luminaire: Blue to N, Brown to L, Green/Yellow to Ground. If using a junction box, bring the
circuit wires through the rear hole into the luminaire.
3.
Close the front cover and tighten the screws securely and make sure wiring is not pinched. Apply silicon sealant (not
provided) to seal all holes in luminaire housing and between housing and mounting surface to weather-proof your outdoor
installation.
Safety – Maintenance - Environment
•
Do not cover the product. Do not attach other items to the product. Store and install the product out of the reach of
children. Only use the product when it is working perfectly.
•
Do not touch the product in the event of a fault or breakdown. Immediately switch off the product and disconnect the
power supply.
A
A
B
B
B
B
AC 100V-240V 50-60Hz
110°
-20 ~
40°
IP65
235mm
190mm
360mm
www.bailey.nl
Verwandte Anleitungen für Bailey 139851
Inhaltszusammenfassung für Bailey 139851
- Seite 1 Do not cover the product. Do not attach other items to the product. Store and install the product out of the reach of children. Only use the product when it is working perfectly. • Do not touch the product in the event of a fault or breakdown. Immediately switch off the product and disconnect the power supply. www.bailey.nl...
- Seite 2 Warranty The warranty period will begin on the day on which the product was purchased from Bailey and will end after 2 years. If a defect occurs within the warranty period as a consequence of material faults and/or manufacturing errors, Bailey will repair or replace the product.
- Seite 3 Garantie De garantieperiode begint op de dag waarop het product bij Bailey is aangekocht en eindigt na 2 jaar. Indien er binnen de garantieperiode een defect optreedt als gevolg van materiaal- en/of fabricagefouten, zal Bailey het product repareren of vervangen. De garantie dekt niet de gevolgschade en tevens worden er geen eventuele voorrijkosten, verplaatsingskosten of installatiekosten vergoed.
- Seite 4 Garantie La garantie commence à la date de facturation du produit chez Bailey et prend fin après 2 ans. En cas de panne pendant la garantie à la suite d’un défaut matériel ou de fabrication, Bailey réparera ou remplacera ce produit. La garantie ne couvre pas les dommages indirects et ne couvre pas les frais de déplacement ou d’installation éventuels.